Avalon 2005-12 :: Check Engine Light On And Code Is P0327 (Knock Sensor)
So, I have my check engine light and the code is p0327 (knock sensor). Clear cose but it returns. Going on for 3 days now. I was suspicious that something else is going on. I also remembered I've been using a little more antifreeze in the reservoir. So, today I needed to watch the coolant. I ran the car for an hr and I found a lot. Red coolant on my belt, the back passenger side of my engine and it was caked on with coolant. I think the water pump is going up.
I was concerned that coolant was also leaking from the intake manifold but it's only the right side, so I'm pretty sure the coolant is being slung around from the belt. I rinsed the engine down and the knock sensor code went away. Temporarily, until more coolant got back there. Do you think I will need to replace the knock sensor along with the water pump or should the sensor work ok after some intense cleaning after the water pump replacement?
Subaru - Forester :: 2002 - Check Engine Code For Knock Sensor - Motor Mounts?
2002 Subaru Forester I took my car to the Auto Zone to read a check engine code. It came back as being a "knock sensor". Besides that I needed a battery, and when the guy was putting it in he said my engine was moving too much and that I probably needed motor mounts.
I was looking at a discussion back in 2010 and the Subaru specialist told the person needing motor mounts is rare for a Subaru, is that true? I'm taking it to a mechanic, what should I expect? how many motor mounts does a subaru have?
Passat (B6) :: Knock Sensor Code After Valve Carbon Scrubbing Service
I have a '07 Passat Wagon 2.0T with 80K miles. I just had the carbon scrubbed off the valves (looked like black popcorn stuck in there!) and now I'm getting a "P0327 Knock Sensor 1" light. The motor seems to run just fine (actually much better now without the carbon build-up). I'll clear the code but it will show up again the next day.
What could cause the code? Could it be related to the recent scrubbing (fully removed and replaced the valve cover in the process), perhaps a chunk of carbon floating around in the tubes somewhere? I want to go back to the guys that performed the service but I want to have a good idea of what could be the problem and the fix before I get there.
Passat (B5) :: 2002 - Cat Warm Up Threshold Low Code / O2 Sensor
I have a 2002 GLX Wagon 2.8 30v, and was getting Cat warm up threshold low code, on the driver side due to the cat being bad. As a temp fix I decided to use spark plug haulers to gap the sensor. When I removed the O2 sensor I wiped the dirt off with a paper towel, which was clean and dry. I put the sensor back on, but now I am getting 4 codes which won't go away. p0036 p0056 p0141 p0161. These are O2 heater circuit codes both bank 1 and 2. I did not touch bank 2 so I don't know how I could have caused this error. I tried to take off bank 2 sensor but it is really stuck on there.
View 3 RepliesSanta FE SM (2001-06) :: Code P0325 Knock Sensor
What is the possible, or most likely, cause of a Knock Sensor No 1 Circuit Malfunction reading??
View 1 RepliesPassat (B5) :: 2002 - CEL Code For Bank 1 Sensor 2 Heater Circuit Fault
Got the CEL Bank 1 Sensor 2 heater circuit fault. Is that the rear right post-cat oxygen sensor? What is correct part number or possibly a link? 2002 2.8l Passat V6...
View 3 RepliesAccent RB (2012+) :: Code PO326 - Faulty Knock Sensor
2012 Hyundai Accent. I am getting a po326 code. Wondering if it may be a faulty knock sensor. And po463 fuel level sensor code when I fill up with gas.
View 2 RepliesHyundai - Accent :: Check Engine Light Came On - Knock Sensor Code
I have a 2012 hyundai accent. The check engine light came on. The code read knock sensor. Before I could get it into a shop, it went off. It didn't come back for 11 months. When it did come back, the same code was read. Again, it went off the following day before it could be looked at and hasn't been seen since. The shop says that even though there is a history code, it would be hard to diagnose since it isn't an active code. I noticed absolutely no difference in performance when the code was active. Both times it went on, the car was idling for several minutes with the ac on, and it came on as i accelerated onto a highway immediately afterwards. However, it has idled like that many other times without the light coming on as well.
View 11 RepliesLexus GS 2006-11 :: Check Engine / VSC Lights On - P0333 Knock Sensor Code
I just purchased a 2006 GS300 AWD w/115k. Started car on lunch hour to find check engine / check VSC lights on. Ran codes to find P0333 Knock Sensor code. Vehicle seem to run perfectly fine, but now that the light is on, it is definity spark knocking under acceleration. This is my first Lexus / Toyota product, so I am unfamiliar with the common problems or fixes. Are knock sensor replacements common?
View 6 RepliesAccent LC (2000-05) :: Code P0326 - Can A Knock Sensor Be Influenced By Heavy Bass?
I have upgraded my sound system in my car and sometimes i get a P0326 check engine light.
Now i was wondering if its possible that the Heavy bass ( 25/40 Hz, 1200 Watt RMS and 2500 watt Max) Subwoofers could cause the car to vibrate so much that it sets of the knock sensor?
I have read some things about it but i only found that several "Old" cars with OBDII would have this problem? Is that the same on this hyundai accent?
It only comes once in a while after long cruises and bumping.
Jetta - Volkswagen :: 2006 - CEL Code P0332 / Knock Sensor 2 In Bank 2 Faulty
I have a 2006 VW Jetta with 92K miles and just a couple of days ago my check engine late came on and when i took to an auto store to check the code, it came as P0332, Knock sensor 2 in bank 2 is faulty. Three things have happened all around the same time and I am not sure if they are related and are just coincidence.1.Check engine light came on.2. I have noticed after that, my car RPM has dropped, idles at about 600-700RPM and when trying to accelerate, it tops at 3000 RPM and feels like the motor cuts off at that point and I have to step off the gas and the car runs ok again, but cant go over 3000.
Had trouble getting on the interstate due to this and thought the car was going to stall, but it didn't. just had to back off the gas and let it run, It did go up to the speed that I wanted, but seems like it wont go past the 3000 RPM point.3. My fuel gauge, drops to empty when it reaches the half way mark on the meter. It stays at the correct level when I start and keep the car in idle, but when I start moving, it drops to empty. When I fill up the tank, it goes all the way to F, and after the car goes the usually of about 190-210 miles, when It reaches the half full level, the meter drops to zero, so have been using my trip odometer to drive after that.
Golf IV / Jetta IV :: Slight Vibration - Knock Sensor 2 (G66) Signal Too Low (code P0332)
I got my car in November and I just did a scan and got this code. I don't have a CEL on. I do feel a slight vibration from time to time. It's very light.
Should I clear all DTCs and then run a scan a couple of days later to see what codes I truly have? Or should I address this code?
If yes, what should I do about this code? Do I need to buy a new knock sensor or should I check the wiring first with a voltmeter?
Ford Super Duty (1999-2016) :: Code Showing For Knock Sensor?
Code was showing for the knock and climbed under the truck and checked to see if it was plugged in grabbed the wire and to my surprise the wire kept coming and so did a piece of the knock sensor, is this going to affect my truck badly?? worst case?? 97 f250 4.6 standard
View 4 RepliesAvalon 2005-12 :: Check Engine Light Remains On With Code P0327
I replaced the water pump. Huge problem. I will get rid of the car before I replace that again. But, it is replaced and the car is functioning.
Unfortunately, the check engine light remains on and I still get p0327(knock sensor) code and car has a slight ruff run.I have the Actron code reader(fairly cheap, but effective) and it will clear the vsc but not the check engine. Upon restart, the check engine light reappears in 7 seconds followed by the vsc symbol. This has been for a week now. So I have been dreading tackling this project next. But I figure if I'm doing this, I better change the rear plugs and maybe the rear coil packs as well.
Don't want to do this, but whether I do it or send it to the dealership, once is all I'm gonna do. I say all of this and yesterday, the check engine light goes away on its own and full power is back and ruff run gone.
I still plan to go into the engine this year because my car just hit 120,000 miles and i have to change my plugs. If it recurs, I will change it all. I will just wait. Only going in once.
Accent LC (2000-05) :: 2002 - Code P0106 / Map Sensor Code
Ok had a check engine light. It directed me to replace the IAT sensor.. After some research I found it was integrated into the MAP sensor. Purchased a new sensor and replaced. Drive about 15 miles CEL throws another code. P0106 (sensor i just replaced) faulty Map sensor.
Followed procedure to replace sensor.. unhook battery cable reset ecm. After reset engine is hard to start. Followed by RPM changes (assuming its the ECM re-adjusting). Then CEL flashes 5-6 times and goes out, Drive 15 miles. Map sensor code reappears. (note i only purchased one sensor But repeated install 2 times).
My thought is against wiring. since the codes refer to different signal wires one for IAT one for MAP sensor. Faulty replacement sensor?
2002 Accent 1.6L
Golf IV / Jetta IV :: 5 Engine Fault Codes - Cam Position Sensor / Knock Sensor / Secondary Injection Pump And Mass Air Flow
I recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..
View 9 RepliesGolf IV / Jetta IV :: 2002 GLX V6 Misfiring When Cold - CEL With Cam Sensor Code
I just got this car it a 2002 jetta glx vr6 12v 5 spleed. It has a miss new plugs wires gas and used coil pack. It misses especially when cold check engine light on says cam sensor changed it and still same thing if I clear the code it comes right back.
View 1 RepliesCamry :: V6 2002 Throwing Code P1130 And P1135 - A/F Sensor?
So my 02 Camry V6 has the check engine light on. I had them scan at AutoZone. the codes that came up were P1130 and P1135. After reading some threads here, seems like it's the A/F sensor?
Just to confirm, there are two A/F sensors in the V6 model? I can see the front one easily but not the rear one. Need to identify which sensor needs replacement?
Elantra XD (2001-06) :: 2002 - Cam Sensor Fault Code P0340
I recently took my car to the Hyundai dealer who told me that my engine light was from a bad cam sensor (Fault Code = P0340). I bought the sensor from the Hyundai parts dealer and replaced it myself. After having the code erased, the check engine light comes back on (with the same code) when I turn the car off and turn it back on, after driving it for a while (30 minutes or more).
View 5 Replies