Passat (B7) :: MAP Sensor Is Going Haywire - Got P0106 Code?
So, the MAP sensor in my car is going haywire. Interesting effect. Some days it is a bit low on power. Other days, I feel like I need to tackle the 'Ring! I will be replacing it but, it would be nice to have that extra spunk. Should I assume a tune will do this?
View 8 RepliesAccent LC (2000-05) :: P0501 Speed Sensor Code Lit Up
The MIL light up and I got the P0501 Code. (Speed Sensor. I use a Scangauge II and the Speed is 0 KM/H at any speed. (was working before). But the in dash Speedometer work no problem. I look on the HMAservice web page and did not found where is located the Speed Sensor.
View 9 RepliesAccent LC (2000-05) :: Recurring Cam Sensor Input Low Code
About 3 weeks ago, I purchased a 2001 Accent GL 4dr 5spd from a friend of mine. A few days later, the CEL came on. I went to O'Reilly and got the code pulled, it was for a cam sensor input LOW. I replaced the sensor and was on my way.
Yesterday after starting the car for the first time for a few days (I wasn't driving because it needed a clutch), the light came on. Has it gone bad again or is something causing the signal to be low? Maybe a low output on the alternator or low battery? The interior lights dim slightly when the brake pedal is applied while the car is running.
Accent LC (2000-05) :: Camshaft Position Sensor Code P0342
So my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 RepliesAccent LC (2000-05) :: Code P0342 - Camshaft Position Sensor
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 RepliesAccent LC (2000-05) :: Code P0335 / Replaced Crank Sensor / Still No Spark
Like the title says...'02 Accent,1.6 dohc.Won't start.No spark.
Pulled code p0335-crank sensor circuit A.
Replaced sensor...still nothing.
Is there something else that commonly goes with these symptoms?...or did I just get a bum sensor?
Also,once I try starting or turn key on,I hear a buzzing coming from throttle body area for about 10 seconds even after key is off. Not sure if its related or normal.
Accent LC (2000-05) :: Transmission Temperature Sensor Location / P0711 Code
Wife's car threw a p0711 code. It says temp sensor failure or whatever. I found the part on rockauto for 22 bucks but that's not the issue. I've tried searching about this and I seem to find some stuff about elantras and sonatas. I can't seem to find anything specific to a accent. I've read that it's inside the transmission which is fine I've changed valves before and such on old rwd transmissions. But some things I find say it's on the bottom and some say the side. Also wiring is mentioned pretty often with service bulletins.
View 28 RepliesAccent LC (2000-05) :: Code For Output Shaft Speed Sensor - Transmission Rebuild
I had a rebuild done on my 2002 Accent. My question is now we get a code for the output shaft speed sensor. Would this have been replaced as part of the transmission rebuild?
View 2 RepliesAccent LC (2000-05) :: Code P0326 - Can A Knock Sensor Be Influenced By Heavy Bass?
I have upgraded my sound system in my car and sometimes i get a P0326 check engine light.
Now i was wondering if its possible that the Heavy bass ( 25/40 Hz, 1200 Watt RMS and 2500 watt Max) Subwoofers could cause the car to vibrate so much that it sets of the knock sensor?
I have read some things about it but i only found that several "Old" cars with OBDII would have this problem? Is that the same on this hyundai accent?
It only comes once in a while after long cruises and bumping.
Accent LC (2000-05) :: 2002 - Idle Varying Between 600 And 2500 RPM / Code P0507
Granddaughter showed up with her '02 Accent idle varying between 600 and 2500 rpm. Disconnected Idle Speed Control Actuator and engine runs at very high idle so apparently the ECM is unsuccessfully attempting to manage the idle and the ISC is functioning. Reading P0507 code. Checked for vacuum leaks beyond throttle body, found none.
The car was involved in a fender bender accident a couple days before the idle issue. No CEL until a couple days after the accident. The varying idle started many days after the CEL.
The wreak cut a half dozen wires in the area outside of the battery. She repaired them and I just finished redoing with solder and shrink wrap. Found no faults with her twist and tape repairs or any other damage to wiring. Varying idle still there.
Accent LC (2000-05) :: 2002 - Code P0121 / Idle Surging Between 1500 - 2500 Rpm
I have a 2002 Accent 1.6L 72K miles, idle surging between 1500 - 2500 rpm after stopping from 50 mph, (with Code P0121) replaced TPS - No Luck . I reset the DTS error codes, ran it with a new TPS and same exact problem, Code P0121 came back, and surging continued, this happens when I decelerate from high speed- 50 mph or so and it will not go to normal idle, surges between 1500 and 2500 rpm when in park.
If I give the throttle pedal a good kick, the problem goes away, and it idles fine, nice and smooth and at normal rpm, the DTS code will clear, and stays cleared, mil light goes out. It almost seems like something is sticking, I know its not the throttle itself because when I do a live data, the TPS shows "0", if I manually push the throttle shaft closed at the throttle body, it is fully seated shut, so I know its not a sticking cable or anything. Can a sticking MAF sensor cause this? Maybe what I'll try tomorrow is rapping the throttle body with a rubber mallet while its surging, maybe something is not returning to its normal position in there.
Passat (B7) :: 2012, 2.5l - Diagnosed CEL With P0106 Code
Had CEL light come on with the code P0106 barometric pressure sensor.
View 2 RepliesJetta - Volkswagen :: Check Engine Code P0106 / Clean Throttle Valve
VW Jetta SE 2.5L... Took my car to the dealer for a check engine light, the code came back P0106 which states I need my throttle valve cleaned and the dealer also said I need my brake vacuum pump replaced.. Do these go hand in hand? How should I proceed with the dealer? I have only 60,000 miles on my vehicle was there a recall on this issue? The dealer already updated the software in the technical bulletin.
View 2 RepliesSonata NF (2006-10) :: Throttle Body Cleaning Due To Rough Idle Occasionally / Code P0106
Trying to clean the throttle body on my 09 sonata 2.4L due to rough idle occasionally (throwing P0106, replaced MAF sensor still same problem), one quick question, is it okay to force the valve open (with connector disconnected of course), and is "re-learning" necessary and what's the proper way to do it?
View 2 RepliesAccent RB (2012+) :: Code PO326 - Faulty Knock Sensor
2012 Hyundai Accent. I am getting a po326 code. Wondering if it may be a faulty knock sensor. And po463 fuel level sensor code when I fill up with gas.
View 2 RepliesHyundai - Accent :: Check Engine Light Came On - Knock Sensor Code
I have a 2012 hyundai accent. The check engine light came on. The code read knock sensor. Before I could get it into a shop, it went off. It didn't come back for 11 months. When it did come back, the same code was read. Again, it went off the following day before it could be looked at and hasn't been seen since. The shop says that even though there is a history code, it would be hard to diagnose since it isn't an active code. I noticed absolutely no difference in performance when the code was active. Both times it went on, the car was idling for several minutes with the ac on, and it came on as i accelerated onto a highway immediately afterwards. However, it has idled like that many other times without the light coming on as well.
View 11 RepliesAccent MC (2006-11) :: CEL / OBDII Code P0141 - O2 Sensor Heater Circuit Malfunction
CEL/OBDII code P0141 - O2 Sensor Heater Circuit Malfunction
So I just bought this car 64k well maintained but cant get rid of the check engine light. Replaced downstream O2 sensor with no luck. As soon as I get home I'll check voltage @ connector. Lets test the O2 sensor connection and test the pins to make sure there is no break in the wires.
Accent MC (2006-11) :: Code P0707 - Transmission Range Sensor Circuit Low Input
The MIL light came on and I noticed the shifting P-D or P-R was hard. Checked the Transmission Fluid and noticed it was low. Topped it up, but still MIL is on and shifting hard still. I bought a OBD2 Scanner and it returns P0707 "Transmission Range Sensor Circuit Low Input". Should I try clearing the DTC? It's a drag because it's my wife's car and she's driving mine.
View 1 RepliesPassat (B5) :: 2002 - Cat Warm Up Threshold Low Code / O2 Sensor
I have a 2002 GLX Wagon 2.8 30v, and was getting Cat warm up threshold low code, on the driver side due to the cat being bad. As a temp fix I decided to use spark plug haulers to gap the sensor. When I removed the O2 sensor I wiped the dirt off with a paper towel, which was clean and dry. I put the sensor back on, but now I am getting 4 codes which won't go away. p0036 p0056 p0141 p0161. These are O2 heater circuit codes both bank 1 and 2. I did not touch bank 2 so I don't know how I could have caused this error. I tried to take off bank 2 sensor but it is really stuck on there.
View 3 Replies