Passat (B5) :: Can't Remove Sway Bar Link Bolt Out
Car: 02 Passat GLX 4motion V6 AWD
I'm in process of replacing the rear strut and I can't remove the way bar link bolt out. It is really tight into the inner rubber and it won't buzz. The bolt sits in a way that I can't use a hammer.
Golf IV / Jetta IV :: Coil Pack Sparking When Try And Remove Hex Bolt
I'm in the middle of replacing my VC gasket and while I was removing one of the hex bolts that holds it in it started sparking like crazy and turned the tip of the hex wrench glowing red. It didn't do this for the first bolt I took out. I also forgot to disconnect the battery before I started, could that have had anything to do with it?
View 6 RepliesFord Excursion :: Changing Rotor - Can't Remove Broken Bolt?
I was in the process of changing out rotor and pads and my caliper bracket bolts while loosening them. The weird part is the bolt was turning in the process. The passenger side was easy as pie. The drivers side has me stuck. I have tried to drill out the broken bolt but noting is working. I don't know where to go from here. I have already purchased a new caliper and the bracket that goes with it. I just need to get this old one off so I can move on.
View 14 RepliesFord F-150 - 1997-2003 :: 1999 - Ratchet Extension To Remove The Bottom Bolt?
My 1999 Ford F-150 failed inspection for frayed driver-side seatbelt (a common problem according several parts sellers). I have obtained a used shoulder harness assembly from a salvage yard but I have two questions:
What is size of the Torx bolts? (the star shaped ones) Looks like T55 but I don't have any to compare. I'll need to buy the socket and I assume a generic version will fit my ratchet.
The top part of the harness looks simple enough to remove but do you need a ratchet extension to remove the bottom bolt?
Ford Super Duty (1999-2016) :: 2002 F350 - How To Remove Spark Plug Wire Bolt
Went to change the plugs on an 02 f350, the bolt holding the plug wire boot on doesn't seem to fit any standard size socket. 7 is too big, 6 is too small. 1/4 is too small, 9/32 is too big.
View 14 RepliesPassat (B5) :: Bolt Loose On The Tie Rod
Have 2001 B5 2.8 4Mo. I have the bolt loose on the tie rod. I have the nut loose on the pinch bolt. I have the lock nut loose on the linkage. The tie rod will slip out 1/4 inch but will not come out of the way. I have hammered the crap out of it. Still no go.
View 6 RepliesPassat (B5) :: What Should Be The Bolt Pattern For 99 1.8t
What bolt pattern the wheels are on my 99 passat. Fairly new to the game. and can I put on the audi phat fives or the S4 wheels also what problems are run into when you put on 17's. does it mess up the on board computer that computes mpg and all that good stuff?
View 4 RepliesPassat (B5) :: Changing Sway Bar - Can't Get The Bolt Out
I did change my motor mounts this weekend but when I tried to remove the sway bar,one of the nuts jammed on the bolt. Let me explain:The nut unscrewed well until the lasts mm, and then, the bolt head came loose, so it was spining freely with no way to remove it but cutting it, the bolt seems to be BUILT IN the alum. bracket that supports the engine mount. Question: can I change this bolt or is it really built in the bracket? I searched on ETKA but it just shows the nut and I can't find the bolt that I need.
View 1 RepliesPassat (B6) :: Bolt Failure On Oil Pump Assembly?
Bolt failure on oil pump assembly in 2.0t FSI engine
View 9 RepliesPassat (B6) :: What Is The Part Number For Torque Insert Stretch Bolt
As the title implies I need the part # for the OEM VW Stretch bolt that holds the Torque Arm insert in place. I've had the mount on my car for a few months now and I've grown tired of it.
I re-used the OEM bolt the first time and I think I'm better off replacing it as it may not be wise to unbolt it and re-torque it for a third time. Looking for the part # for the stretch bolt? I believe it's 21mm.
Passat (B6) :: Replacing Brake Lines - Banjo Bolt Torque Setting
Going to replace brake lines tomorrow and would like to confirm the torque spec on the actual banjo bolt as not to break them but also don't want to leave them too loose...
View 3 RepliesPassat (B5) :: How To Get Passenger Side Engine Mount Bolt To Stop Spinning
So I just replaced my oil pump and i am reassembling my front end and I just cant get my passenger side engine mount bolt to stop spinning so i can get the nut on (the mount underneath the car) , I have no clue how to stop the spinning
View 1 RepliesPassat (B6) :: Changing Lower Control Arms / Driver Side Bolt Is Hitting Transmission Oil Pan
I changed the Passenger side with no problem , the driver side bolt is hitting the transmission oil pan. I am thinking of loosening the mounts and try to jack the pan up to get that 1 clearance or worst case drain the transmission take the pan off remove the bolt and put in fluid in. If I drop the the transmission pan is there a filter in there? also how much transmission fluid does it hold.
[IMG] ....
Passat (B6) :: How To Remove DRL
Without vagcom?
View 8 RepliesPassat (B6) :: How To Remove The Air Vents
How to remove the air vents?? Center along with Drivers/passanger side. Bentley shows to use a trim tool/wedge and looks like they just pop out.
View 1 RepliesPassat (B5) :: 1.8T - How To Remove The Shifter
I wanted to know how to remove the shift knob from the 1.8t and yes its a 5 speed!..
View 2 RepliesPassat (B6) :: How To Remove Trunk
Removed the trnk emblem from passer sedan? I'm looking to spray it....
View 17 RepliesPassat (B5) :: How To Remove Outside Door Handle
I have to remove the outside door handle in order to make a repair on the door. I did remove the torx screw from the side of the door but still doesnt come out.
View 3 RepliesPassat (B5) :: Can't Remove Cv Joint Boot
I have a 2004 1.8T 4Motion (automatic) that blew a CV joint boot. After inspection of the other side, I decided to replace both (just the outer boots). Got the axles out without much trouble but now I cannot drive the joints from the axles. I've tried both and neither is cooperating, I've knocked out off them with a mallet but they aren't budging. Is there something to do besides just driving them off?
Axles are tubes (hollow) p/n's 8D0 407 271 (& 272) ED.