Prius C :: Mileage Off On Dash And Scan Tool Is Different
question to the smart people out here in prius land. Plug in my scan tool and it shows the mileage as 4219 mile but yet the dash in the car show 4334 miles why would they both not be the same.
View 12 RepliesGolf IV / Jetta IV :: 2001 - Getting Check Engine Code P0343 And P0321?
I just got a 2001 VW Jetta. I got it with the Check Engine light on. Went to my local AutoZone to get a OBDII reading, got codes P0343 & P0321. P0343 Camshaft Position Sensor A Circuit High Input B1. P0321 Ignition/Distributer Engine Speed Input Circuit Range/Performance. So for P0343 I got the Camshaft Position Sensor for $70 and for P0321 got Crankshaft or Speed Position Sensor for $110 ( FYI, Crankshaft Position Sensor & Speed Sensor are the same ). Paid $160 to get both sensors replaced. I know both sensors are easy to replace but it was easier to pay..
View 3 RepliesAccent MC (2006-11) :: No Power To Scan Tool When Connected To OBD Port
Nothing is happening when I plug in my scan tool that I've used a million times before. I'm assuming it's a fuse but nothing listed on the fuse panel. Checked a few vague ones with no luck.
View 5 RepliesCamry :: 2003 XLE I4 Would Crank But Doesn't Start - Scan Tool Not Connecting To ECU
Car in question is a 2003 Camry XLE I4. On rare occasion when I try to start up the car, it would crank but doesn't start. Sometimes two or three hours later and it would start right up with no problem. This has been going on for months now.
Well today the car all of a sudden died on the freeway. It was running like usually and next thing I know, it just died. In all cases no check engine light pops up at all. I got it towed back to the shop and the mechanic tried to hook up a scan tool but it couldn't connect to the ECU. Also when the key is turn over to the "on" position before starting, no CEL pops up at all. All fuses and relays are good.
ETA : It turns out the wiring under the fuse box was bad. The fuse box and wiring were either replace or repair. Since this is an intermittent problems, we will see if this is indeed the fix after a couple of months.
Ford Excursion :: 1989 - Changing Brake Lines - Need Scan Tool?
Next on my list of needed repairs is new brake lines. The ones running along the frame are rusted pretty bad. I had a 89 F-150 bust a line once and it got real interesting so I would like to change these before that happens.
I have searched and still not gotten a clear answer as to whether I need to get a scan tool and do something with the ABS pump. I would like to know if the scan tool is necessary.
Passat (B5) :: OBD Scan Giving Error Codes P1136 And P0441?
Shop said o2 sensor and they just want to replace one. I can get universals for around 80 each, will they work if this is in fact the problem?
View 1 RepliesAccent MC (2006-11) :: 2007 - Code P0343 / Car Not Starting Cannot Hear Fuel Pump
It was acting rough and was a little loud. Like a low deep loud, the engine light came on. I tried to start it, it would crank but no start.
Code came up P0340 (Cam sensor) So i replaced it, reseted and scanned again, now it says P0343 To much input sensor 1 bank 1. When i turn the key over to "ON" I don't hear the fuel pump, is this normal?
I don't understand what to do I am so lost, I am ready to do the timing. Is there something cutting my fuel pump out or is it done? Do i do the timing, or replace the pump ...
Ford Aerostar :: Truck Does Not Accelerate Properly - Scan Error 128
I have a problem I could not solve. 1994 Ford Aerostar my truck does not accelerate properly, the scan shows:
VID 20150624 235001 - YouTube ....
On my list reads. I cannot find how to solve this.
Avalon 2005-12 :: CEL Error Code P0440 Error Code / Charcoal Canister Replacement
So of course it has to happen 3 weeks after my warranty expires. My CEL comes on and I have it read and the result is P0440. I find out that my wife has a habit of topping off the gas tank and so I am thinking that she has probably ruined the charcoal canister. It is something easy to replace?
I have an 06 limited edition... Yes, she will not be topping off any gas tank anymore.
Ford :: Can A Faulty Injector Cause P0301 Scan Code?
The vehicle is a 2002 Ford Windstar van with a 3.8L V-6 engine. It has a constant miss on the #1 cylinder. That's the one on the backside of the V-6 on the passenger end of the engine. I have changed the plug(s) and still had the miss and P0301 code. The plug's wire has about 7500 Ohms, so it's not the problem. I hear no snapping of a high voltage short to ground. A friend suggested that the injector might be the issue, but I am of the opinion that the scan code shows only a high tension or secondary ignition system issue, and not fuel injection issues. I'm thinking the problem is more likely to be the coil pack.
View 19 RepliesSanta FE SM (2001-06) :: Error Code P0446 Came On
I've checked the lines from the Purge Valve on the Passenger side of the Intake Manifold, Check OK
I've Checked that Valve OK
I've Replaced the Canister Close Valve
I've got the Gas Cap tight.
I've removed the rubber bushing holding the CCV to the Evap Canister, hoping to isolate the Filter and point the blame on it, no luck there!!
I'm thinking next is to drop the Tank and check over all the Goodies on top.... as much as I hate the thought of that, the two access holes under the seats, just don't allow access to enough of the tank!
any thing there that I could suspect, I see there's a check valve!
There's also the Fuel Tank Pressure Sensor, which may be at fault.
Prius (2001-03) :: Keep Getting Error Code P1437
keep on getting this error code....I think I have exhaust leak , Would that trigger this code ?....is an Exhaust leak is considered a Vacuum leak??
View 1 RepliesFord F-150 - 1997-2003 :: CEL Came On - Diagnostic Tool Reads Code 401 / EGR Insufficient Flow
I just bought a 1997 ford f-150 4x4 with 4.6 motor. the check engine light came on. My diagnostic tool reads code 401 (egr insufficient flow). I've replaced on the parts on the egr side of engine. light still on. could it be a leak in the vacuum lines. I don't see any wear.
View 4 RepliesPassat (B5) :: CEL And Error Code P1476
I have this error code on my VW 1999 passat 1.8T automatic car. How to resolve it. My friend reset it and CEL went off for few days and now it came back again. How to resolve it??
View 2 RepliesPassat (B5) :: Getting Error Code 0012?
It happened to passat. Once I hit about 75mph on highway I get a stop engine (oil presser low light). It flashes than goes off once I lower my speed. I checked all fluids are normal. It throws a 12 code an says oil passage blocked, cam positioning sensor, skipped timing chain. These are what the code says could be wrong with it. The car runs fine with no hesitation at idle or normal city driving. I have already flushed the oil with cleaner, and still getting the light.
View 5 RepliesSuburban :: 2001 - Error Code Replace EGR Valve
Have 2001 suburban with the 5.3. Mechanic has replaced EGR valve 3Xs. Error code specifies "replace EGR valve". Each time car runs fine for 4-6 weeks (500-1000 miles) and then service engine light comes on. Shortly thereafter the car will not idle correctly (under 1,000 rpm) and will die at stop. I think the EGR valves are getting clogged up with carbon. Car has 130,000 miles on it.
View 4 RepliesPrius (2001-03) :: P3100, P3125 Error Code Came On
My Wife was driving our 2001 Prius and got the big triangle and the car went into limp mode.
The Codes were P3100 (info code 196) and P3125 (info code 325)
P3100/196 = Internal Error - Generator CPU Malfunction
3125/325 - Inverter Internal Short. - Generator Inverter Fin - Inverter Internal short
Clear the codes and the car runs fine, but the problem will eventually resurface.
The dealer wanted tor replace both the converter/inverter and HV ECU.
I purchased replacement converter/inverter from Ebay and inverter coolant pump (new) and installed.
Problem eventually resurfaced. I purchased replacement HV ECU from ebay and installed.
Engine would not start (does not attempt to even turn over), but was not throwing any codes. I had this same symptom with a third HV ECU as well. The part numbers on the HV ECU were exact matches.
Santa FE SM (2001-06) :: 2003 - Error Code P1159
It seems that i'm most likely going to have to replace the entire plenum .
P1159 here are some details. [URL]..................
I've checked all connecting wires and none appear to be loose. When the issue started to occur and prior to discovering the P1159 code, I also replaced all coils. I replaced the coils because one was arching over to the metal of the engine. I assumed this may be my problem. The issue still persisted obviously. The check engine light never came on so I assumed I wouldn't get a code. I took it over to a friends house with a code reader and that's when I discovered that it was actually giving the P1159 code.
Are there any other model cars that utilize the same engine that I could use the plenum from? Getting this in working condition is going to be the difference in what I can get for it.
Accent LC (2000-05) :: 2001 - Code P0121 TPS Error
2001 1.5L 5-speed Accent
I did a search on this problem and found several people posted the same P0121 code. Strangely many people wrote that replacing TPS did NOT fix it. The code came back in 30 miles or so. Most of them didn't follow up what finally fixed it and only 2 people did by saying they got the code cleared by fixing/replacing:
1. Leak in the intake manifold, bad plug wires, etc.
2. New Head & ECM.
Is there any known fix for the P0121 on Accent 1.5L other than above?