Camry :: 2002 - Grinding Noise And It Won't Move In Reverse Or Drive
I replaced the front hubs and bearings on my brothers 2002 Camry today. He drove less than a block and developed awful grinding noise and it won't move in reverse or drive. It rolls when I put it in park. I had to pull it back into my shop. Is it possible the inner CV came loose and i didn't realize it? It all seemed to go back together fine. The new CV axle nuts were quite tight and slow to put on with my impact gun.
What else could possible go kaput when I re & re hub/bearings? And what a long ugly job to replace those bearings. Don't even think about doing this without a good hydraulic press. Up to the point of getting knuckle off, it was easy job.
Lincoln - Towncar :: 2001 - Intermittent Vibration When Move The Gear Shift Lever To D For Drive
I have a 2001 Lincoln Town Car that has an intermittent vibration that can be felt when seating in the car and you move the gear shift lever to D for drive. The car has 141,000 miles. It is an automatic transmission. The vibration cannot be felt when touching the steering wheel. What could be causing the vibration?
View 3 RepliesTouareg :: Oil Pressure Gauge Doesn't Move Until Drive For About 15 Minutes
The oil pressure gauge in my 04 v8 treg doesn't move until I drive it for about 15 minutes. Is this normal?? When THE BEAST is idling it takes about 15 minutes to pass 60 on the oil pressure gauge. I find this very odd.
View 3 RepliesLexus GS 2006-11 :: Brake Clicking When Move From Reverse To Drive?
I have a 2008 GS350. Been having brake clicking when I move from reverse to drive and lately been happening more when driving regularly. Brought it in to Lexus to get the complimentary 19-point inspection and they said I needed new brake pads and rotors. I did do a search and found it can be issues with front spindles, sway bar, bushings.
View 5 RepliesGolf IV / Jetta IV :: Post Oil Change - Car Will Not Move In Drive Or Reverse
I just changed my oil in my mk4 jetta 1.8L and after draining the oil, changing filer, and adding new oil, the car will not move in drive or reverse. Once I give it gas it will move but that's at the higher rpms. I am almost positive I didn't remove the transmission oil but I am just not sure.
View 12 RepliesSanta FE SM (2001-06) :: Auto Transmission Will Not Move In Reverse Or Drive
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 RepliesSubaru - Outback - Transmissions :: Car Won't Move In Drive, Reverse Or Neutral
When I started my car and put it in reverse, it didn't move. It felt like my front, right wheel was in a divet or was being blocked somehow (intuitively it seemed like if I accelerated enough, it would eventually move, but since there was nothing physically stopping it - that I could see - I didn't want to break something by doing that). I tried putting it in drive and neutral and the same issue was still there. I put the car up on a jack and checked one wheel at a time - I could move each wheel completely around in both directions.
I could move the steering wheel all the way to the right and to the left. I tried turning off the 4-wheel drive and that didn't do anything. At this point I'm concerned it could be the transmission or the drive shaft, but I'm not sure what to look for in order to know if I need to get it towed to a shop (hoping I can avoid this) or if there's a simple test I can do, or a way to "reset" something if it may be locked. I haven't had anything happen to the car that would have been of concern.
Ford F-150 - 1997-2003 :: 1998 - Cannot Get It To Move In Drive Or Reverse
I have a 1998 f150 4x4, the truck has not been driven in a few years and it’s been outside in my driveway up on jack stands. I just rebuilt the front end and did a four wheel break job, after getting the truck off the jack stands, I can't get it to move in drive or reverse. I also noticed that when you go from reverse to park the gears grind and I can't even get it to shift into 4H. I checked the tranny fluid and it is fine, also the tranny was just rebuilt a few years before I stopped driving the truck.
View 6 RepliesFord Transmission :: 1994 F53 E4OD 460 CID Will Not Move In Drive Or Reverse
I been working on this unit and I running into this
no foward
no reverse
no foward in and gear at all
I have to check pump pressure
I'm changing fluid and filter
1994 F53 460 CID will not move in drive or reverse - iRV2 Forums
Ford - Aerostar :: 1997 Van Will Not Move When Put In Drive Or Reverse And Push Gas Pedal
I have a 1997 ford aerostar van that i recently acquired through some family,when i got it it was running fine but has recently started having troubles.The Question i have is this i put my car in drive or reverse and push the gas pedal the car doesn't move.....we have tried putting transmission fluid into it and that worked temporarily. What it could be except just a bad transmission?
View 2 RepliesSubaru - Impreza :: 2001 - Hard To Get Into Gear And It Would Not Move In Reverse / Neutral Or Drive
I had a problem with the CV Axle and the Wheel Bearings. I replaced them already and I ran into another issue with the Wheel Studs and the Ball Joint, so I ended up replacing them as well. Yesterday I put everything back together after replacing all the parts mentioned before and I made sure everything was bolted down and tightened, and then the tire back on and lowered the jack. I started up my car expecting it to drive just fine and it was harder to get into gear than before and it wouldn't move in reverse, neutral, or drive. I called a Monroe Muffler around here and they told me that the CV Joint is probably not seated all the way inside the Transfer Case.
So later the same day I took everything back apart and made sure that I put the CV Joint back into the Transfer Case and I put the pin back in and made sure that both CV Axles would turn at the same time, which they did. I figured it was good so I put it all back together again and went through the same process as before, making sure everything was tightened down, all the bolts and nuts and pins were where they needed to be. Everything seemed to be good. I put the tire back on again, lowered the jack, started the car and attempted to drive it again. It still won't move. Why this is happening.
Ford Escape / Hybrid :: 2003 - Truck Will Not Move When Put It In Drive Or Reverse And Press The Gas
I have an 03 Escape that is very difficult to start after it rains, if I open the hood and let it dry out for a few days it starts fine, however if I put it in drive or reverse and press the gas it will not move... if I hold the brake while it is in gear and give it gas it does not rev up, however if I put it back in neutral or park it revs up. I normally cover the hood with a tarp to prevent this from happening however I was shutting the tarp in the door and a lot of water got in the floor board of the truck I sucked it all out, that night the radio started playing all on its own, I came out to the truck turned the radio off it stop went back in came back a while later and it was on again, so I pulled the fuse... but there are two buttons that stay lit on the radio the preset button 1 and 2 stay on all the time and I can not figure it out either. This is my beach truck I only use it for that purpose..however it is fall fishing time and I really want to go...
View 4 RepliesHyundai - Accent :: 2002 - Motor Runs But Rear Wiper Doesn't Move
During recent cold/ice spell, went to use my rear wiper and heard a pop (there was ice around the wiper base), then the wiper was flipping all over the place. Now I can hear the motor running but the wiper doesn't move. Plus, I can easily move it around by hand - no resistance. Do I have to replace the whole motor or is there possibly a gear or linkage between the motor and arm that stripped or popped away, so that can be fixed? 2002 Hyun Accent.
View 5 RepliesElantra XD (2001-06) :: 2005 Doesn't Go Forward At All If Shift Into Reverse And Then Go Back Into Drive
I recently bought my '05 Elantra from a small dealership and I'm starting to see a problem with it. If I shift into reverse and then go back into drive, the car doesn't go forward at all. I have to mess with the gear shift a bit to get the car moving. I'm pretty sure it's a bad linkage. The dealership I bought it from said it desperately needed motor mounts when they got it so they replaced 2 of them. I'm sure the problems are related. I can't find any information on replacing it myself though.
View 1 RepliesCaravan/Voyager :: 2002 Van Will Not Move Into Any Gear / Won't Go Forward Or Reverse
The gear shift works fine, and we lifted the hood and saw that the mech. arm IS working when we shift. However, the van will not move into any gear. won't go forward, reverse, etc... it acts like it isn't shifting.
i was driving down the highway, and noticed it wasn't accelerating and stepped on the gas.. .and nothing. I stopped the van, put in park, turned it off. Started it again, and put in D and wouldn't go, just engine revved. then put in reverse and same thing... didn't move but engine revved.
Santa FE SM (2001-06) :: 2002 Auto - 4wheel Drive Doesn't Shift Into 5th Gear
Have an 02 Auto with the 2.7, 4wheel drive, and it doesn't shift into 5th gear. Can go through the 4 gears with the manual shift, but when just in drive, only shifts up to 4th. At 65mph, RPM's over 2500.
View 3 RepliesLumina :: 1993 - While Turning Makes Grinding Clattering Noise - Won't Move Forward But Will Move In Reverse
I'm new here and I am having issues with my Lumina. It is a 93 Chevy Lumina Euro 3.1L 6 cylinder and has 192K miles on it. It has had one owner for the past ten years that I know for a fact.
Here's what happened. I was coming back home (2hr trip) The brakes had started making that roaring sound on the way down and had gotten worse when I got ready to make the trip home. Okay so I know the brake pads needed to be changed. No big deal. Well going down the road at 65mph I round a curve and my car starts making this REALLY LOUD grinding clattering noise. It took me forever to get it stopped. I will still in the road and I needed to get it out bc it was right around a curve. So I put it in drive and it wont move. So I put it in reverse and it moves just fine with no problems and no noises made. After backing it out of the road I tried to put it in drive. It moved forward a few inches and stopped like something was binding it up.
So here's the problem.. it will move in reverse with no problems at all and only creeps a couple of inches forward then stops. The harder you press on the gas the more it tries to lurch forward but will not move.. like it's caught on something.
We changed the rear brakes on it. Discovered that the driver side rear rotor and caliper were broke beyond repair so we replaced those too. Still the same.. moves forward a lil bit and stops but will go in reverse just fine. We don't seem to think its the tranny bc it pulls hard and seems to not have any problems pulling.. but its like something is bound up somewhere. That is the best way I know how to explain this situation.
Chevrolet - Blazer :: Barely Move Forward And Will Not Move In Reverse
My trailblazer will not move in reverse , and will barely move forward, i checked transmission fluid hot and it's not even on the dipstick but when it was cold. it was?? Do I add more or what?..
View 9 RepliesPontiac - Bonneville :: 2002 - No Reverse In Drive
I have a beautiful 2002 Pontiac Bonneville SSEI with just over 100k miles on it. I've been saving for a new set of tires and a new regulator for the rear window. The window suffers from the "pop and drop" syndrome but I have instructions on how to fix it myself when I can get the parts.
Yesterday, I started her up to go to my second job when I discovered I had no reverse. In drive, I could just creep forward at 3000 rpm. Fixing a transmission is probably the worst case scenario I could imagine happening.
I'm left with two options: Either find something simple I can do myself to get it moving again or get what I can for it and use the proceeds to buy a piece of metal to get back and forth to work.