Ford Super Duty (1999-2016) :: Front End Had Noise / Standard Sway Bar Link Knock
2004 F-250 140k 4wd 6.0. Front end had noise, standard sway bar link knock. I disconnected the sway bar on the drivers side and drove it around. Smooth and noise free. Determined new links were needed, Installed new links and now even more noise. Disconnect them and no noise again. What am i missing? Bushings look good on the axle. Is the pressure from the sway bar putting strain on another wore part?
View 5 RepliesGolf V R32 :: Rear Sway Installed And Now Knocking Noise Coming From Passenger Side
I installed my sway on saturday and it went smoothly. The bushings were greased up, bolts were torqued to spec, nothing was rubbing or touching in anyway. Now I am getting a knocked noise coming from the rear passenger side. after driving it for a day or so i check under the car to make sure nothing loosened up and everything was just how it was when i installed it. What the issue could be, but the noise is really annoying.
View 4 RepliesFord Super Duty (1999-2016) :: Front Sway Bar And Drag Link Too Close
This is my sway bar and drag link look like with the wheel turned all the way to the right. When I took these pictures, I had put the right tire on the curb too see what it was going too look like. However. Even with all wheels on level ground. It still is running very close. When the steering is straight, I have maybe 1" to 1.5" clearance between the 2. My truck does have a readylift 2.5" level kit on it. Running like this stock or leveled? Should I look around for longer sway bar links?
View 2 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Driver Side Rear Sway Bar Link Upper Bolt Removal
I have a 2004 F250 Lariat Crew Cab FX4 6-3/4' bed.
What is the procedure to remove the Driver's side Rear Sway Bar Link upper bolt? - the link attaches to the frame. The nut is on the inside of the frame with about 1/3" to 2/3" clearance between the frame and the fuel tank. Of course, the frame's "C" shape faces towards the inside.
Golf IV / Jetta IV :: Sway Bar Laying On Passenger Side Axle
I recently just lowered my gti and I noticed that the sway bar was laying on my passenger side axle. I put adjustable end links on but that did not got the problem either, this car I daily drive.
View 10 RepliesGolf IV R32 :: Clicking Noise When Turning On Front Passenger Side
The front passenger side is making a clicking noise when it drives and turns. It started earlier today, but it went away and then it started happening again when I got home. i am guessing its my axle ( the axle was rebuild). My dad took it for a ride and said its not the axle and that something is loose. but that's his opinion he is not a mechanic I have fk coilovers and I had all the bushing replaced. I doubt its my suspension I just installed it about 2 months ago.
View 3 RepliesPassat (B5) :: Can't Remove Sway Bar Link Bolt Out
Car: 02 Passat GLX 4motion V6 AWD
I'm in process of replacing the rear strut and I can't remove the way bar link bolt out. It is really tight into the inner rubber and it won't buzz. The bolt sits in a way that I can't use a hammer.
Ford Excursion :: Sway Bar Down Link Keep Loosing?
I am having difficulty with my front sway bar downlinks, they keep coming loose. I have recently replaced them for the same reason with some O'Reilly Auto Parts house brands, they seemed alright when compared to the Motorcraft replacements, they even had grease fittings which was unusual for some of the others I have seen. I have torqued them down, I have tried red locktite, the only thing I have not tried is to weld them. It is only the lower nut which keeps coming loose.
View 9 RepliesFord Excursion :: Sway Bar End Link Bushing
My Ex has a 4-inck Sky Jacker lift and I need to replace one of the sway bar end link bushing. Is the bushing size same as the stock ones? Need to know so I can order the right ones. What is the Energy Suspension part#....
View 1 RepliesGolf V R32 :: Popping Noise Coming From Front Passenger Side When Reversing?
Almost every single time I put my .:R in reverse and the car starts moving I hear a popping noise with pauses in between each pop. I think it might be a ball joint and the noise is coming from the front passenger side.
View 18 RepliesGolf IV R32 :: Removed Front Sway Bar Endlink / Double Clunk Noise Vanished
So I'm backing out of my driveway today and I hear the loudest (in one of my cars) double clunk noise ever, coming from the passenger side front. Turns out one of my kw v2's decided it wanted to try and come apart at that corner.
Note: I had one side on a jackstand and could not find the cause until I removed the front swaybar endlink. It was putting tension on the arm and not allowing the movement to be found.
The shock insert inside the coilover body was moving up and down about a 1/8 inch clunking at the top and bottom of its travel. This is the retainer that loosen causing the clunking. I found that the spanner wrench from my dewalt angle grinder, fit the retainer well enough to tighten it down snug.
Golf/GTI VI :: 2013 - Knocking / Clunking Noise Coming From Passenger Side Front
I drive a 2013 4 door gti. Car has 4k miles. Just last weekend myself and my buddies threw my coils in. FK Silverline X plus'. I am not sure on the measurement from fender to ground but I am a finger gap in the front, and fingertips in the rear. After throwing my coils in on saturday, I had an alignment and the rear camber adjusted. Just today, sunday, while driving home I heard a weird clunking/knocking noise. Previously I drove a mk4 and I know the sound of sway bar on axle and this is not the sound. Its coming from the passenger side front.. and I can sort of feel it through my clutch and brake. After pulling the car over I checked everything I could. wheels are all tight, struts seem fine. The noise occurs continuously even on smooth roads. The knocking/popping is pretty loud and can be heard in cabin. My buddy had mentioned the guys the aligned my car might have forgot to tighten something so I am heading back to the shop first thing in the morning.
View 3 RepliesGolf IV R32 :: Loud Buzzing / Vibration Noise From Front Passenger Side Behind The Dashboard
Background: I brought my R in for service last week because the AC stopped working. I ended up needing the compressor and the fans replaced. I picked my car up and drove it home with no problems. The next day I drove it I started to hear a rather loud buzzing noise that sounded like something was rattling loose from the front passenger side of the car behind the dashboard. It was loud enough to hear over the stereo while driving on the freeway.
Thinking something was wrong with the newly installed fans I brought the car back to the dealership and now they're telling me the fuel pump needs to be replaced. From what I understand, the fuel pump is in the back of the car under the rear seats and attached to the gas tank. I explained to them that I'm a bit confused because the sound is clearly coming from the front of the car but the mechanic there insists what I'm hearing is the fuel pump. Am I crazy or does what they're saying sound reasonable?
I tried looking at a couple YouTube videos that had sound of a VR6 fuel pump gone bad but the sound was nothing like what I was hearing.
Golf V R32 :: ST Lowered Back Down And Loud Noise Coming From Front Passenger Side?
I have a set of ST that were put on a year ago. I raised them up in October for the winter. This past Saturday I lowered the car back down. As soon as I did I have the loud noise coming from the front passenger side.
I know it's not the top hats because I had that issue and replaced it and not the same noise. It is not the clunk that people associate with springs.
The noise seems to happen when spring/strut expand and retract.
Called ST today and they said if I had the car all the way down it is my fault. WTF? Why would you make a coil that is adjustable and the customer is able to go all the way down and then say it's my fault IF strut is blown?
The car drives straight and smooth so I dunno if it is blown. Could it be because of a build up of crap between the springs over winter (I saw some.)
Lexus ES 2007-12 :: Metal Thump - Replaced Sway Bar Link
2008 ES 350 sway bar replace, confirmed diagnose of metal thump, like dead blow metal to metal, mostly bumps, rough roads. etc, it wasnt' a vibration, but finally moved the sway bar link up and down on jack stands and could see and hear the top joint of the sway bar link moving.
It wasnt a bad job, but if your in the Rust Belt, the nuts aren't happy coming off, and I highly recommend a air saw to ease the pain. If you dont have a saw, and your in the Rust Belt make sure you clean the heck outta the rust in the threads, cause it just jams the works as your easing the nut off the stud.
Need 17mm wrench (i used box end rachet) and 6mm allen , its got that stupid set up off the allen slot in the end of the stud to steady that, and they you gotta work the bolt off at the same time, not a one hand operation.
Start by spraying the snot outta the 17mm nut and stud with Blaster, Hold onto the allen key wrench and I whacked the rachet with a dead blow hammer and was able to get it to bust loose, now you just have to ease the nut off with whatever it'll give you. After I got some room for the air saw blade, I just whacked it with the saw.
Careful if you just start with a cut off operation into the rubber boot of the stud, there is a shoulder that wont allow it to just pull thru, you have to cut the stud on the nut side of the sway bar in order for it to pull thru.
Ford Excursion :: 2000 V10 - Sway Bar Link Rattles Constantly
I recently replaced Sway Bar Links on my 2000 X (V10, 4x4, 155k). They were only a year and half old but the bushings had gave way. Mechanic went with an OEM part with a new design from NAPA. This new design added grease fittings. Now the truck rattles constantly and seems to have more sway. Shocks are probably originals, but I don't think they are the main cause. I can tell the rattle is coming through the frame. All my suspension is stock.
View 14 RepliesFord Super Duty (1999-2016) :: Sway Bar End Link Mounting Bracket
We all know the sway bar end link problems in the early superdutys. Several years ago I installed energy suspension bushings and thought the problems were gone. Lately it started clunking again. I tightened the bolts with a breaker bar and it worked. but now it making noise again. I purchased a set of mevotech end links. Upon installation I found the problem.
Over the years of clunking the bolt hole on the upper driver side is no longer round. It has become oval shaped. I read a couple threads on here about this problem. I can't drill them out as the mevotechs have studs not bolts. Can I get the mounting bracket that bolts to the frame. Its a triangle shaped piece that the end link stud goes through. I have tried searching for it online to no avail. Whats it called?
Ford Super Duty (1999-2016) :: 2000 - Sway Bar Link Arm Removal
Working on my 2000 Excursion, 7.3, 4x4. Replacing front sway bar link arms and sway bar bushings. I got the driver side arm and the sway bar bushings done and have run into a problem removing the passenger side link arm. When removing the top connection bolt there's not enough clearance when extracting. I've gotten it loose, but as I go to pull it off, it butts up against the bell housing with about an inch of bolt left to clear the frame.
View 1 RepliesFord Ranger / B-Series :: Missing The Nut On Top Side Of Front Stabilizer Bar Link Bolt Assembly
Today while driving I noticed a knocking when turning right or going over bumps in the road. I finally got to look under the truck and noticed that I'm missing the nut on the top side of the front stabilizer bar link bolt assembly on the passenger side.
It's a '99 Ranger XLT 4x4. Is this unsafe to drive? Is there a bushing on the top?