Ford Ranger / B-Series :: Changing Stabilizer Bar End Link?
Is this hard to change out?
View 7 RepliesSonata I45 (YF - 2011+) :: Front Stabilizer End Link Noise
From day one my 2011 Sonata Limited left front suspension has been very noisy especially over road reflectors or other abrupt irregularities in the road surface at slow speeds. I've always felt I had a bad strut or strut mount but I believe it's the ball socket in the front sway bar end link. Has to replace these to remove a knocking sound and had it go away afterwards? I test drove a 2013 Limited and it was solid and noise free over the same surfaces so I know something isn't right. I also see no aftermarket kits for these. I find the rear ones but not the front.
View 19 RepliesGolf IV / Jetta IV :: Steering / Suspension Assembly Bolt Missing
While changing the oil on my car I noticed that a bolt was missing from the steering or suspension assembly (not really sure what its for. I was wondering what it is for and how important it is. I went to the store to get a replacement and found that the threads in the hole have all rusted out so I can't get a new bolt in. Is this something I should definitely fix before driving again or is it not too serious.
Here is link for the pictures: [URL] ....
Ford Super Duty (1999-2016) :: 2004 F250 - Driver Side Rear Sway Bar Link Upper Bolt Removal
I have a 2004 F250 Lariat Crew Cab FX4 6-3/4' bed.
What is the procedure to remove the Driver's side Rear Sway Bar Link upper bolt? - the link attaches to the frame. The nut is on the inside of the frame with about 1/3" to 2/3" clearance between the frame and the fuel tank. Of course, the frame's "C" shape faces towards the inside.
Ford Ranger / B-Series :: 1994 - Blew Fusible Link To Alternator After Rebuilt Head?
I bought a 94 2.3 did a head job bought a rebuilt head and got it all back together hooked up the battery and blew the fusible link to the alternator. Did I screw something up? I have been rebuilding engines for a long time and never had this happen. Tested the alternator and the O'Reilly guy said that the Voltage regulator was shot putting out 17 amps and that is why the fusable link blew. I don't think that's right because the engine was not running I just hooked up the battery, and no I did not switch the pos and neg. I'm dumb but not that dumb. Any guesses?
View 1 RepliesFord Ranger / B-Series :: 1983 - TK5 Shifter Assembly Replacement?
My 1983 Ranger is in the shop. I'm being told that I need to replace the shifter assembly. I understand that this is a Mazda part, from a TK5 transmission. These parts are interchangable between bronco ii's of the same era.
View 1 RepliesFord Ranger / B-Series :: Broken Bolt At Downpipe On Exhaust Manifold
This is for a Pontiac Vibe. I broke one of the bolts that connects the exhaust pipe to the exhaust manifold. Need to get some type of nut/bolt/spring that I could use to fix it. The bolt is sticking out of the flange about 3/4" if I had a long nut to screw onto that?...........
View 6 RepliesFord Ranger / B-Series :: 1996 XLT - Front Driver Side Spindle
I'm normally in the bullnose section, but recently started working on my father-in-law's 96 ford ranger. He wanted me to replace the front rotors.
I replaced the passenger side without a hitch, but when I went to replace the driver's side, I noticed the cotter pin and castle nut were missing. A nail was in the cotter pin's place. I backed off the spindle nut and found that the threads were eaten up, as was most of the spindle with various gouges and nicks.
1996 Ford Ranger XLT 2.3 ......
Ford Ranger / B-Series :: Constant Thud Coming From Front Driver Side While Driving
When driving down the road, there is a constant "thud thud thud" coming from the front driver's side of my 99 Ranger. I've been looking online for about two hours now, going back and forth to my truck to see if I can figure out the problem. All I've come up with is that it's the sway bar links. they're both disconnected, and I'm going to replace them anyway, but would that cause the constant thudding?
View 3 RepliesFord Ranger / B-Series :: 2002 4X4 - Loud Bang / Pop Comes From Driver Side Front Tire
Bought a 2002 ranger with a four liter in it. Didn't notice until actually going off-road there is something wrong with the four wheel drive. In 4 high it will drive good for a random distance then a loud bang, pop, comes from what feels like it's the driver front tire. The faster you're moving the worse it is. It's not consistent at all.
Replaced the transfer case shift motor and both CV axles. Still does it. Walked next to the truck while it's moving and the front tires look like something is in a bind and it's causing the bang. Beating my head against the wall at this point.
On a side note it has something wrong with the tranny. Taking off it feels like someone bumped the rear, and after about twenty minutes of driving od light starts blinking and it shifts hard from first to second. Kill it, cures that specific problem just not the takeoff problem. Not sure if this is all related. Pulled the pan and refilled with as much fluid as came out. Which was a dark red. Still having same issues.
Ford Ranger / B-Series :: Missing When Started And CEL Came On
I have a 98 Ranger with a 3.0 (5 speed) that has 254,000 miles on it. I drove it to town this morning (8 miles) and it ran normally. I stopped for just a few minutes at a house and when I re-started the truck, it was missing very bad and the CEL came on. It wouldn't haul itself in anything higher than 3rd gear. I decided to try to make it back home. I drove it less than two miles and it cleared up and started running perfect again. I came home anyway and read the code with my scan tool.
It said that I had a miss fire on cylinder #5. I erased the codes and shut the CEL out and its been running perfectly ever since. (I have put about 150 miles on it so far) If it does it again, I will start by replacing the plug wires. I have already done that but its been a long time ago. The plugs have been replaced twice as well. I was wondering if it could be something other than electrical like a dirty injector or maybe the compression rings lined up and it momentarily lost compression.
Ford :: 2006 - Motor Mount And Front Stabilizer / Rattling Noise From Driver Side Engine Compartment
My 2006 AWD LTD 500 has about 52000 miles on it; a slight rattle/clunking noise is intermittently heard on driver's side in engine compartment. Took it in to dealer who says motor mount is cracked and front stabilizer bar joints are worn and both need replacing. Car has only been driven on highways or for short trips (3-4 miles) and has had no impacts nor been driven over rough roads or run over any potholes or such. Should the motor mount be damaged? At 52K miles?? Never heard of such a thing. Ditto, the stabilizer bar joints: worn out in under 60K miles? What can I do about this? Who seek relief from? Ford warranty is, of course, over, and supplemental warrenty will only cover motor mount replacement but not stab bar. Are these parts routinely wearing out at such an early date that repair shops can reap the rewards???
View 4 RepliesFord Ranger / B-Series :: 2001 - Driver Side Front Brake Line Broken / Replacement
My front driver side brake line broke. It had a typical double flare fitting at the caliper but at the distribution block on the other end it had a flared fitting that would be used on a industrial hydraulic unit. I took it to the NAPA store and they told me to cut the nut off the old line and put it new line and double flare it. I did and it leaks. Do I need a special fitting on the end that goes the distribution block?
View 2 RepliesFord Ranger / B-Series :: 2001 2.3 - Missing When Accelerating?
I have a 2001 ranger 2wd with a 2.3. It has a miss when acceleration. There is no check engine light. I have changed: fuel filter. Plugs, wires, crank position. Sensor, cleaned mass air flow sensor. Ran 2 bottles of injector cleaner in it. Still missing???? It runs and idles great. Just has a miss in the lower RPM's 1000-2000 then goes away. I really don't wanna take it to a shop. What do you all think??
View 11 RepliesPassat (B5) :: Can't Remove Sway Bar Link Bolt Out
Car: 02 Passat GLX 4motion V6 AWD
I'm in process of replacing the rear strut and I can't remove the way bar link bolt out. It is really tight into the inner rubber and it won't buzz. The bolt sits in a way that I can't use a hammer.
Ford Ranger / B-Series :: 1985 - Missing At High Acceleration?
85 ranger 2.3 fuel injected misses at high acceleration. Fairly new plugs and wires, just replaced the timing belt, pretty new fuel pump in tank, new fuel pressure regulator and pcv. It idles well, starts up and drives pretty well until you get it in 4th and really bog it down. Could be timing issues but I'm pretty sure I did everything right when I put the belt in. What it could be? I know when the tank fuel pump went out, it did something similar for a while...
View 9 RepliesFord Ranger / B-Series :: 1988 - Missing / Stumbling Especially At About 55 MPH While In Overdrive
I've got a 1988 2wd Ranger with a 2.9l v6. I just recently got it running. It has been setting for awhile. I replaced fuel tank, both pumps, fuel filter, Plugs, Wires, Cap, Rotor, TPS. It ran great for about 100 miles. Then yesterday on my way to work about 4 miles down the road it started to miss/stumble especially at about 55mph while in overdrive. When I got home I pulled the codes and I got KOEO 22 Map sensor signal out of voltage(engine off), 53 TPS signal voltage to high, 95 Thermactor Air System Problem, or Fuel Pump Monitor signal, indicates circuit problem.
KOER I got 21 ECT sensor signal voltage out of range or loss of signal during normal operation or Crank Sensor problem, doesn't have a crank sensor I believe. But I did change the ECT sensor and it still stumbles and seems like it misses. Noticed it is sluggish getting up to speed kinda surges and bogs. Im at a loss it isn't showing any more codes. Checked all plug wire connections and made sure everything was making connection. The only other thing I can think of is that the ignition module on back of distributor is going bad. Not advancing the time correctly.
Ford Ranger / B-Series :: Fuse Box Panel Cover Missing
I've a 1994 Ranger XLT 4.0L with a missing fuse panel cover. I'm trying to get the horn to work and we've traced the problem to a missing fuse. Unfortunately, there are 3 empty fuse slots and no info on their rating or use. Where I can get the proper info. Truck was a salvage, no ops manuals, and sloppy work putting it together.
View 14 RepliesFord Ranger / B-Series :: Missing On Light Throttle / Cruise
4.0. I'm having what feels Like a Miss on Light throttle/cruise. Once warmed up it's fine. Idle is fine too. There is No CEL/Codes.
View 14 Replies