Ford Super Duty (1999-2016) :: Front End Had Noise / Standard Sway Bar Link Knock
2004 F-250 140k 4wd 6.0. Front end had noise, standard sway bar link knock. I disconnected the sway bar on the drivers side and drove it around. Smooth and noise free. Determined new links were needed, Installed new links and now even more noise. Disconnect them and no noise again. What am i missing? Bushings look good on the axle. Is the pressure from the sway bar putting strain on another wore part?
View 5 RepliesFord Super Duty (1999-2016) :: Sway Bar End Link Mounting Bracket
We all know the sway bar end link problems in the early superdutys. Several years ago I installed energy suspension bushings and thought the problems were gone. Lately it started clunking again. I tightened the bolts with a breaker bar and it worked. but now it making noise again. I purchased a set of mevotech end links. Upon installation I found the problem.
Over the years of clunking the bolt hole on the upper driver side is no longer round. It has become oval shaped. I read a couple threads on here about this problem. I can't drill them out as the mevotechs have studs not bolts. Can I get the mounting bracket that bolts to the frame. Its a triangle shaped piece that the end link stud goes through. I have tried searching for it online to no avail. Whats it called?
Ford Super Duty (1999-2016) :: 2000 - Sway Bar Link Arm Removal
Working on my 2000 Excursion, 7.3, 4x4. Replacing front sway bar link arms and sway bar bushings. I got the driver side arm and the sway bar bushings done and have run into a problem removing the passenger side link arm. When removing the top connection bolt there's not enough clearance when extracting. I've gotten it loose, but as I go to pull it off, it butts up against the bell housing with about an inch of bolt left to clear the frame.
View 1 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Driver Side Rear Sway Bar Link Upper Bolt Removal
I have a 2004 F250 Lariat Crew Cab FX4 6-3/4' bed.
What is the procedure to remove the Driver's side Rear Sway Bar Link upper bolt? - the link attaches to the frame. The nut is on the inside of the frame with about 1/3" to 2/3" clearance between the frame and the fuel tank. Of course, the frame's "C" shape faces towards the inside.
Ford Super Duty (1999-2016) :: 2008 F250 - Front Passenger Side Brake Rub / Drag
My 2008 ford f250 SD Powerstroke has a bad front passenger side brake rub/ dragging after offroading before off roading just rubbed a little now it drags a lot. what do i need to fix.
View 2 RepliesFord Super Duty (1999-2016) :: 2012 F350 - Hellwig Front Sway Bar Installation?
Installing the Hellwig 1 1/4 inch Front Sway Bar on their 11 and up F250 or F350 SRW Pickup?
My 2012 F350 Super Cab LWB XLT 6.7L seems to have quite a bit of sway in the front end. This is especially true moving slowly such as turning into service stations or other off angle turns. The truck only has the FORD OEM puny Rear Anti Sway Bar but the front seems to accentuate sway. The Truck has Rancho 9000XL Shocks, Timbren Enhanced Suspension System as well as Torklift Quick Release Stable Loads in the rear.
The Truck I have is not overloaded but it does carry an Eagle Cap 950 Camper pretty much full time. True the Campers now days are tall so some sway is expected. I just want to reduce the apparent front end sway and wonder if others have used the Hellwig Sway Bar in the front.
Ford Super Duty (1999-2016) :: Greaseable Sway Bar Bushings And End Links
I have a 2002 F350 4x4 CC 7.3 i am wanting to change the sway bar bushings front and rear to poly and I want greasable bushings to avoid the squeaking that you get with these bushings alot of the time. I would like to change the end links to poly too i realize these wont be greaseable. What was the outcome and where did you buy the bushings. What is the size of the front and rear sway bars and the length of the end links??
View 14 RepliesFord Super Duty (1999-2016) :: Sway / Stabilizer Bar Links Rattling?
I'm on my second set of links. The replacement were Dorman 3 years ago. They are rattling again. Do I just replace them again? I forgot to add, the bushings were replaced this year.
View 1 RepliesFord Super Duty (1999-2016) :: 2003 - Sway Bar Bushings Specs?
What are the specs for the sway bar bushings that go in the retaining bracket for a 2003 ford f250? went to advanced auto last night to get some got mine off my truck and the one they gave me was a little too small for my sway bar and the retaining bracket.
View 2 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Sway Bar Bushing Replacement?
I have a friend with an 01 f250 super duty who needs to replace sway bar bushings.
View 6 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Sway When Driving On The Highway
I have a question about my 2001 Ford F250 and the scary road sway I experience on the highway.
I thought it was the garbage and nearly bald tires and the fact that the fronts were bigger than the back, (Previous Owner). I went and got new E rated 265's from Discount Tire.
It actually made the swat feel worse. I thought maybe the tire guys inflated them all to 80 PSI as the sidewalls indicated. I check today and found that they went with the recommended PSI on the door sticker. 60 Front and 80 rear. But this is for the Tire size listed on the sticker.
After the tires cooled here at home I increased the PSI to 80 all the way around. I am having trouble finding my specific problem even though there is a lot of talk in many forums about this issue.
If this does not work should I try lower PSI in the rears and leave the front at 80? Should I try a front steering stabilizer shock? I did tighten up the steering box and took the minor slop out of it, Not is just makes it respond to the sway correction quicker.
Ford Super Duty (1999-2016) :: Difference Between Rear Sway And Traction Bars?
I was going to add a rear sway bar to make the truck more stable after lifting it but then I thought when I eventually do a cummins swap, with all the torque and the tall block i have in the back ill get a lot of axle wrap so i will need traction bars. So what is the difference between them? will a rear sway bar stop axle wrap as well as body roll? Also will traction bars stop axle wrap and decrease body roll? I just don't want to get a sway bar now and then need traction bars and have to get rid of the sway bar.
View 14 RepliesGolf V R32 :: Noise In Front On Passenger Side - Sway Bar Link?
Chasing a noise in the front, seems to be more on the passenger side, and I think I have it narrowed down to the link ends or subframe. I have ST coil overs, came on the car, and already did the 034 mounts and bearings to solve another noise but this one is different. The links are original and I saw some performance ones that are a bit shorter for a slightly lowered car. Should it have shorter ones due to the coil overs?
View 5 RepliesFord Excursion :: Drag Link Replacement - Need Tie Rod Too?
I have a new-to-me 2001 Ex V10 4x4 w/ 132k. I'd say it's 85% and I'm slowly working to get it to 100%. Right now, I'm tackling the low hanging fruit. I'm trying to track down the front end clunks and creaks.
I cinched down on the driver side sway bar end link and it took out some of the clunk. I traced the remainder of the clunk to the drag link which I can rotate about 20-30 degrees by hand. Both grease boots are shot.
New rotors and pads get here Monday. While I change them, I'll be working the front end issues as well. I went ahead and bought the Energy Suspension sway bar bushing kit and will swap them all out. I also plan on replacing the drag link ends too.
My question is: do I need to replace my tie rod ends? The grease boots have definitely leaked but I can't detect any slop like the drag link. If the grease is leaking all over is that a sign that they need replacing?
I've never done steering work before but it looks straight forward. Any tips for a novice? Anything I should be aware of before I start? While I'm down there, is there anything else I should change while the steering is apart?
Ford Super Duty (1999-2016) :: Clutch Pedal Close To Floor?
I have a 06 f360 PSD 6 speed. On a road trip and the clutch pedal is getting very close to the floor. No Slippage but the longer I leave the pedal pressed the worse it gets. Are there any good descriptions how the clutch in this truck works?? Slave cyl??
View 14 RepliesFord Super Duty (1999-2016) :: How To Close A Broke Rear Slider
damn motor or something broke and of course its fully open. any tricks to disengage from powered sliding system? just need to get by for a bit til i can get to the dealer.
View 3 RepliesFord Excursion :: Wheel Crooked After Drag Link Replacement
I recently replaced my drag link which was loose and clunking around. I noticed my steering wheel is pointed at 11 while driving straight now. I'm not sure if it was like that before, the vehicle was new to me when I did most of the initial work.
It looks to me like I should be able to just adjust the drag link turnbuckle to change the steering wheel position but I'm not sure. Is that okay to do?
Ford Super Duty (1999-2016) :: Rear Power Sliding Window Slow To Close
Ok, so I have been noticing that the rear power window has been slow to close. So today I open it and now it wont close. When I press the button on the dash, I see the cable snap tight and hear the motor turn on so its not a fuse or motor. What I need to replace/fix. I have tried to blow the track out, tried wd40 tried having somebody hold the button while I try to assist it in closing, but none of that worked. It is now half way and wont go any further.
View 12 RepliesFord Super Duty (1999-2016) :: Manual Sliding Glass Pretty Rough To Open And Close
06' CC F-250... Manual rear sliding glass is pretty rough to open and close, other than cleaning out that track, is there a good spot to put a drop of white lithium grease? Do you have to yank off the rear interior panel to clean it out all the way or would a shop vac with a sharp tip do the trick?
View 2 Replies