Golf/GTI VI :: Stock Sway Bar Endlink Is Screwy

I installed my coil overs this weekend and it took some work to get my passenger side sway bar end link on. It was too short it seemed.the mod ts on the coil overs are I. The same place on both front coil overs. I had to put A LOT of force to get it on there. I'm wondering if other have had this issue and or what did you do? Is it putting a lot of stain on the sway bar or end link. By the way its the stock sway bar as well.

View 1 Replies

Tiguan :: Front End Clunk - Sway Bar Bushings?

My Tig has been doing a sharp clunk (single) for awhile when going a bit too fast over speed bumps. I just ignored it, as I'm not flying over bumps regularly and I had just replaced the OEM struts all around. Now when accelerating over 60 kph the car has a side to side shimmy. Also when compressing or unloading the front end suddenly, like with dips on the road, makes it clunk. Checking the various suspension components?

View 6 Replies

Golf V R32 :: Noise In Front On Passenger Side - Sway Bar Link?

Chasing a noise in the front, seems to be more on the passenger side, and I think I have it narrowed down to the link ends or subframe. I have ST coil overs, came on the car, and already did the 034 mounts and bearings to solve another noise but this one is different. The links are original and I saw some performance ones that are a bit shorter for a slightly lowered car. Should it have shorter ones due to the coil overs?

View 5 Replies

Golf V R32 :: Clunk Noise In The Front Spring

I just installed Neuspeed Springs and my car is taking a "clunk" in the front spring, I went back and I replaced the strut bearing mount and the noise still continues.

View 8 Replies

Golf IV R32 :: Clunk Noise Coming From Front End

I just finished my suspension refresh and I notice a noise coming from the front end. I really think that my end-links are the source of the noise. When I push the car up and down from the center, no noise. When I shake the car from right to left, I can ear a clunk coming from my end-links.

View 1 Replies

Golf V R32 :: Clunk Noise Coming From Right Front After H&R Springs Install

My R's only got 5,400 miles on it and I just lowered it Saturday on H&R Springs and when I turn my steering wheel like 3/4 either way it makes like a clunk noise at lower speeds only....any other part besides strut top mounts and bearings? It sounds like its coming from the right front.

View 9 Replies

Golf IV R32 :: Stock Front Sway Bar Diameter

I'm going to have my front sway bar mounting bushings replaced with poly bushings next week. Shop said they wanted to order 19mm bushings for my car, but everything I see online says its a 21mm bushing. Which is correct? It's a 2004 R32.

View 1 Replies

Prius (Gen 2) :: Front Sway Bar Links Making A Bad Noise

Both of my front sway bar links have a bad joint and are making a bad noise.. I purchased the replacements and tried to loosen the nuts with no success. I put some oil to loosen them and will let them set over night. Next attempt will include a breaker bar.

View 4 Replies

Ford Excursion :: Clunking Noise - Front Sway Bar End Links

I plan on replacing as I have a clunk happening. Thought I'd try here first.

Is there a brand that's better? 1Aauto has OEM. Is there a brand that's better or makes a difference?

Or is a front sway bar end link a front sway bar end link?

View 7 Replies

Golf IV / Jetta IV :: 2004 - Front Sway Bar Rubbing On Axle (Not Lowered)

I have a 2004 GLI that I just completed the slave cylinder on, after i got everything back together my driver side axle is now rubbing really bad on the sway bar where it connects to the endlinks. What could be wrong?

View 2 Replies

Ford Excursion :: Sway Bar End Links / Loud Clunk

I've been having the loud clunk under the drivers side floor, that many others have as well. Did many hours of research and replaced the sway bar end links. Napa only had the left side in stock so I did it first last weekend and did the right side this weekend. One thing I noticed when doing the right side was the hole in the frame was all wallowed out. Drilled out the bushing in the upper end link and used a bigger bolt to fill the gap up. went for a drive and the clunk was way worse than it ever was still on the left side. So I took off the left one and went for a drive. Sure enough no clunk, the left one was wallowed out as well. So I did the same thing on that side and the evil clunk is finally gone. Just thought I would throw that out that if have a clunk after replacing the end links, Check the upper holes.

View 14 Replies

Golf/GTI VI :: Installed GTI Sway Bar - Getting Clunking Noise

So I recently installed a GTI sway bar on my 2010 TDi and was getting a clunking noise. I assumed that it would be the subframe making noise since I've read a lot about that but the sway bar is actually rubbing on the front portion of subframe (the part that bolts to the frame directly above the A-arm). It's hardly touching it but its enough to wear into the bar.

View 4 Replies

Ford Super Duty (1999-2016) :: Front End Had Noise / Standard Sway Bar Link Knock

2004 F-250 140k 4wd 6.0. Front end had noise, standard sway bar link knock. I disconnected the sway bar on the drivers side and drove it around. Smooth and noise free. Determined new links were needed, Installed new links and now even more noise. Disconnect them and no noise again. What am i missing? Bushings look good on the axle. Is the pressure from the sway bar putting strain on another wore part?

View 5 Replies

Golf IV R32 :: Rear Sway Make Noise When Go Over Road Bumps

Rear sway bar make noise when you go over bumps in the road?

View 24 Replies

Golf IV R32 :: Rear Sway Bar Installed Correctly But Makes Noise

So after about 3k on my rear sway I checked everything to make sure its tight. All is tight, but i notice it moves very little but its enough to make noise and drive me nuts. hard to explain but if you see the h&r bar it has very small allen head screws inside a ring that keep the bar in place where it bolts to the frame there is only a 1/16 of an inch or so of play and its driving me nuts.

View 14 Replies

Golf V R32 :: Clicking Noise While Turning Steering Wheel - Sway Bar Bushings?

Front sway bar bushings causing "clicking" noise while turning the steering wheel? Usually happens when I'm moving into or out of a parking spot and while I'm turning my steering wheel. I got the driver side, I believe, lower control arm replaced and after that i started getting a faint clicking noise when I'm turning the steering wheel.

The dealer, after multiple visits, discovered it's the front sway bar bushing causing the noise. They said it's really not worth the cost, since it's isn't a safety issue and the whole sway bar needs to be replace since you can't buy bushings alone. I want to get rid of the noise regardless of safety or not.

View 5 Replies

Golf V R32 :: Rear Sway Installed And Now Knocking Noise Coming From Passenger Side

I installed my sway on saturday and it went smoothly. The bushings were greased up, bolts were torqued to spec, nothing was rubbing or touching in anyway. Now I am getting a knocked noise coming from the rear passenger side. after driving it for a day or so i check under the car to make sure nothing loosened up and everything was just how it was when i installed it. What the issue could be, but the noise is really annoying.

View 4 Replies

Golf IV / Jetta IV :: Squeak Noise / Removed Driver Side Seat Belt But Now Belt Will Not Retract

So I was trying to track down this squeak noise and I removed the drivers side seat belt but now the belt will not retract? It's stuck like this, is there a manual release? Buying another one is not a option right now. And I have to drive the car tomorrow morning.

View 1 Replies

Golf IV / Jetta IV :: Trying To Remove Double DIN Monsoon Unit But Stuck?

I tried to remove the double DIN monsoon unit using 4 OEM VW removal keys. The bottom went fine, the top they went all the way in. So after searching here and other forums, I know the tabs are bent. There were plenty of posts but not many were useful. I tried jiggling the radio around, angling the keys in trying to catch and even pulled the trim from around the radio to see if I could slide something in.

One post said he got it out by pulling apart the whole dash to get at the cage, which I don't want to do. The other said he brought it to the dealer and they could get it out but destroy it. I'd be willing to give that a shot to get this thing out, but not sure how to even go about it.

View 11 Replies