Ford F-150 (2004-2008) :: Torque Value For The Trans Pan Bolts?
I am finally getting around to changing the trans fluid on my 05 f150 5.4 4wd xlt auto, what is the torque value for the trans pan bolts.
View 1 RepliesFord Aerostar :: 1987 - Draining Trans Fluid From Torque Converter?
How to drain the tranny fluid from the torque converter , I am dropping the pan and installing new filter and fluid, I want to get as much of old fluid out as i can It has a 3.0 engine with overdrive...
View 11 RepliesFord Transmission :: 2000 F250 7.3 - Trans Slipping - Torque Converter?
I was driving my 7.3 down the road and it started acting like the trans was slipping, it revved up and tried kicking down a couple times and when I slowed down and went to speed back up it just had no power coming through the trans to the wheels it just revved. I put it in neutral and it idled up for about 5 seconds. I put it in park n shut it down. I fired it back up after looking everything over and it moved about half mile down the road and no power to the wheels again. The trans is full of fluid, is there a sensor that could of went bad or just the torque converter or the entire thing shot? Only owned my truck 6 months has a trans and motor swap already from previous owner. 180k on current motor n Trans. 382k on my truck. t6 4" turbo back banks exhaust only mods I know of.
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: Blown Trans From Torque Converter?
So my transmission drove perfectly fine I just wanted to put an upgraded torque converter in especially after driving a customers' truck with a low stall converter. I know their not like for racing or anything but it's a work Truck with some mods to the motor nothing crazy. So I went ahead and bought a low stall triple disk converter and I drove around the block fine and went to go on the freeway and got into fourth but lost it as I hit 75 (was not flooring by any means and had it in the stock tune) now it will not go past second gear. Once it did this the o/d off light started to flash and I decided to do a stall test.went to 1800 in a Second. Suppose to stall around 1200-1300.
2000 f250 7.3 powerstroke dp chip stage 1 camshaft and 180/100 injectors coming at some point but stock for now
Ford 7.3L Power Stroke (1999-2003) :: Trans Torque Converter Rattle
1999 7.3/4r100 4wd with the rattling torque converter.
I bought this truck 10-11 years ago to use as a tow rig for my landscaping company. It has been a great problem free truck, I have done brakes a few times, a water pump, ball joints but no issues with motor/drivetrain.
I don't know the history of the trans before I purchased. Ford didn't have history of it being replaced and even now it still has all the labeling on the case. I would have thought it would have been washed off in a rebuild. Again I don't know. When I bought the truck it shifted nice and crisp, having owned trucks before it made me think it had been rebuilt but this was my first and only 4r100. Other trucks are ZF6 manuals.
Anyway 10 years and 100,000 miles later it still shifts very crisp and fluid, has been changed a couple times, is nice and cherry red. I added a 6.0 cooler, temp gauge and filter. Never see the temp rise and haven't seen much in the filter.
About 25,000 miles ago the TC started to rattle, a known 99 problem. I figured surely the trans would go and I would do a rebuilt from Ford. It keeps going though so being a work truck I have kept running it.
A couple weeks ago the starter just spun and wouldn't engage. I pulled the inspection cover and noticed some missing teeth on flex plate. Got it to start my turning crank bolt a bit to good teeth and the starter caught. Now we are carrying a breaker bar and socket. It has happened a few more times so I need to replace flex plate.
Question is, since I need to pull trans to replace flexplate, should I replace TC (I would like to get rid of the noise)? Some people have said I will be replacing trans in a couple months if I mess with it. They say just spend $3000 on a rebuilt now with a converter. Not trying to be cheap but hate to just dump this trans that is still working great and has served me well.
I have replaced many transmission and done clutches in many trucks so I am familiar with the steps of removal and installation, just stuck on what I should do.
Ford 6.0L Power Stroke Diesel :: Trans Shifts Hardly - Stays In 5th Gear - Torque Converter?
Ok so here is my problem now. I'm sure its in the tramny but not sure what else. My shift from 3-5 has always been a little hard. Yesterday on my way to work I noticed shifts 1 thru 3 were hitting hard. Once I got up to 65 mph it was okay. Then pulling into work when I shifted to reverse it didn't go into gear right away and then it would hit into gear. Later that evening on my way home from work it was shifting the same but seemed worse. Then my tow/haul light started flashing and it seemed like the torque convertor wouldn't lock in. It would just stay in 5th gear and the more throttle I gave it the rpms would go up but I would only get a little response from it. Then a few miles down the road it just completely shut off on me. It will not even try to turn over. I could also hear a noise coming from underneath the truck. Something ive never heard before. I really need to figure this out
View 14 RepliesFord 6.0L Power Stroke Diesel :: Torque Shift Trans / 4 - 5 Gear Shift Under Hard Acceleration
I have been having an issue with my 4-5 gear shift under hard acceleration and know that a rebuild is due soon but I was wondering if any high performance kit available with all the clutches and friction discs needed to rebuild.
View 6 RepliesPrius (Gen 3) :: Angular Torque Method Is More Accurate Than Standard Torque Wrench
During my 35 years of experience as a production line and service engineer in the aerospace industry, it was my job to determine the least expensive and easiest foolproof way to perform any production and service operation.
Many readers here have related their experience with the oil filter housing and their difficulty with its removal and reinstallation with the need of a torque wrench to correctly tighten it. Most all technical tightening of screw systems have gone to the "angular torque method," as it is more accurate than the standard torque wrench.
Golf/GTI VI :: How To Increase Low End Torque
I have a stage 2 GTI. What can I do to increase low end torque?
From my research, swaping for a k04 is not going to work, in fact its gonna make it worst.
Golf IV R32 :: Loss Of Power And Torque Especially After 3 - 4k Rpm
The car has 108k I bought it with 101k that being said I had no clue when the last tune up was or if the coils were replaced, now I did replace the transmission, transfer case and clutch since then I've noticed a loss of power and torque especially after 3-4k rpm car just seems to fall on its face, if I had to explain it I would say it feels like it went from being tuned to stock, I have no clue if the car had software or not. also some times I get a sputter or almost a hesitation from the rear, I have done the haldex service 2 weeks ago, It absolutely feels like the car isn't breathing right I don't hear the intake as much or cleanly I'm wondering if the intake manifold bushings are bad and could even cause this? doesn't seem to pull as much just from the start though I used to just drive normal and the car almost felt like it was pulling its self doesn't feel anywhere as quick.
View 16 RepliesGolf V R32 :: More Torque When Engine Is Cold?
Feel like the car has more torque before the engine is fully up to temperature? Why I am getting that sensation? Makes me wonder about possible benefits of water/meth injection even on NA.
View 8 RepliesGolf V R32 :: Horrible Dip In Torque And Power After 4000 Rpm
I have an my 2008 Golf mk5 R32 DSG. I have fitted the GruppeM Intake , done the decat and fitted a Milltek Resonated system. I am based around 1.12 miles above sea level and our fuel here is probably the equivalent of your 91. I had the car dyno'd yesterday with the graph below :
1. What is causing the horrible dip in torque and power just after 4000rpm? Do R32 graphs general look like this? Could it be a result of the variable valve timing?
2. I have a feeling my DSG's mechatronics unit is faulty , could that cause a loss in power or have a result on the dyno run?
3. The power does look low but if I convert it to coastal power it looks to be around 150wkw and 300Nm which seems right?
The biggest concern is the dip in the graph ... Power was measured at all 4 wheels ...
Golf IV R32 :: Specs For Bearing Caps And Order To Torque Them?
I need the torque specs for the bearing caps and the order to torque them. Can't find the pdf file for the bentley. Looking for a link to the bentley..
View 24 RepliesGolf/GTI VII :: Clutch Slipping / Cannot Handle Torque Above 3k In 6th Gear
Clutch is starting to slip - can't handle torque above 3k in 6th gear.
6500 miles on the car
700 miles with module
Never launched - just wind out gears occasionally
Don't have to ride clutch on hills
Not a daily driver - not stuck in traffic
I shift like a granny...
Golf IV R32 :: Valve Cover And Intake Manifold Torque Specs
I have to replace the valve cover gasket this weekend.
View 5 RepliesGolf/GTI VI :: Installed BFI Torque Arm Insert - Huge Vibration With Windows Up
I just installed Black Forest Industries Torque Arm insert for the 09+ TSI (He said TDI's work too). Anyways the vibration noise is unbearable with the windows up, it is producing this sound frequency/ pressure that gives you an instant migraine. I am a mechanic and I followed the instructions. You really can not keep the car at idle or you head will explode. If you bring the rpm's up to 1000 its all good as gravy.
View 24 RepliesGolf IV / Jetta IV :: ASR And EPC Light Lit Up / Code P1335 Torque Limit Exceeded
Car shut off while driving to work. ASR and EPC light lit up. Pulled over to the shoulder, car had a really rough idle. Cut the car off and started it back up. Now the pep in my car is gone and it seems like I'm driving with reduced power.
View 2 RepliesToyota - Avalon :: 1995 - Harsh Trans Shift / CEL Blinks Indicating Trans Solenoid Is Defective
I have 1995 Toyota Avalon w/173K miles. It’s in good shape mechanically and cosmetically. My 16 yr old daughter is the primary driver. I have extensive service records and have replaced the springs/struts, o2 sensors, and a few other bits. My question is related to hard shifts and a check engine light. During the summer the trans shifts normally. In the fall & winter, when temps dip below 50 degrees, the trans shifts harshly and the check engine light blinks indicating a trans solenoid is defective. The trans fluid has been flushed twice, most recently in Oct 2008 at the Toyota dealership. My theory is the techs filled the trans with a heavier weight fluid than is necessary and that is triggering the codes.
View 1 RepliesTrans Sport :: 3t40 - Trans Slips When In Reverse Under Load?
If I press the gas a little hard in drive, my tires squeal but if I'm in reverse I can feel a slipping in the trans. If I try to back a trailer up an inclined driveway, it won't go, the trans slips. I have no crud in the pan. I've replaced the reverse boost valve. I installed a Trans-Go kit which is suppose to eliminate the reverse slip but it hasn't worked. Everything else works just fine and my fluid is red. I have engine braking in 2nd and 1st. The van backs up fine, it just does this in reverse under load.
View 2 Replies