Ford 6.7L Power Stroke Diesel :: Little Twang Sound Coming From Trans Between 3 - 4 Gear Shifts
Having transmission problems? Everything I've read before says these transmissions are better than gm Allison's and they can handle up to 600 horse before you gotta worry about beefing them up but mines starting to act funny.
How important is the transmission tune? My truck it's tuned with the spe hot tune and trans tune. Didn't like the way it clunk bang hard shifts though so I ran factory trans tune for a while but it felt very soft like it was slipping when I got after it on the performance setting of spe hot so I went back to spe trans file.
I get a little twang sound that sounds like it's coming from the trans between 3-4 gear shifts, initially only heard it after getting on it hard in performance but it's getting worse and happens on stock power level under light acceleration now sometimes. Also I lost all gears briefly and it wouldn't shift into manual at all when I stopped to turn around the other day.
Working fine in drive but when I shifted out to reverse it had nothing in any gear and manual wouldn't light up on the display. I shut it off and restarted the engine and it came back and worked fine after that but not sure what happened there, don't think it's good though. Did using the stock transmission file with the hot engine tune or the hard clunk bang custom trans file up my trans, freak malfunction?
Ford 7.3L Power Stroke (1999-2003) :: Blown Trans From Torque Converter?
So my transmission drove perfectly fine I just wanted to put an upgraded torque converter in especially after driving a customers' truck with a low stall converter. I know their not like for racing or anything but it's a work Truck with some mods to the motor nothing crazy. So I went ahead and bought a low stall triple disk converter and I drove around the block fine and went to go on the freeway and got into fourth but lost it as I hit 75 (was not flooring by any means and had it in the stock tune) now it will not go past second gear. Once it did this the o/d off light started to flash and I decided to do a stall test.went to 1800 in a Second. Suppose to stall around 1200-1300.
2000 f250 7.3 powerstroke dp chip stage 1 camshaft and 180/100 injectors coming at some point but stock for now
Ford 7.3L Power Stroke (1999-2003) :: Trans Torque Converter Rattle
1999 7.3/4r100 4wd with the rattling torque converter.
I bought this truck 10-11 years ago to use as a tow rig for my landscaping company. It has been a great problem free truck, I have done brakes a few times, a water pump, ball joints but no issues with motor/drivetrain.
I don't know the history of the trans before I purchased. Ford didn't have history of it being replaced and even now it still has all the labeling on the case. I would have thought it would have been washed off in a rebuild. Again I don't know. When I bought the truck it shifted nice and crisp, having owned trucks before it made me think it had been rebuilt but this was my first and only 4r100. Other trucks are ZF6 manuals.
Anyway 10 years and 100,000 miles later it still shifts very crisp and fluid, has been changed a couple times, is nice and cherry red. I added a 6.0 cooler, temp gauge and filter. Never see the temp rise and haven't seen much in the filter.
About 25,000 miles ago the TC started to rattle, a known 99 problem. I figured surely the trans would go and I would do a rebuilt from Ford. It keeps going though so being a work truck I have kept running it.
A couple weeks ago the starter just spun and wouldn't engage. I pulled the inspection cover and noticed some missing teeth on flex plate. Got it to start my turning crank bolt a bit to good teeth and the starter caught. Now we are carrying a breaker bar and socket. It has happened a few more times so I need to replace flex plate.
Question is, since I need to pull trans to replace flexplate, should I replace TC (I would like to get rid of the noise)? Some people have said I will be replacing trans in a couple months if I mess with it. They say just spend $3000 on a rebuilt now with a converter. Not trying to be cheap but hate to just dump this trans that is still working great and has served me well.
I have replaced many transmission and done clutches in many trucks so I am familiar with the steps of removal and installation, just stuck on what I should do.
Ford 6.0L Power Stroke Diesel :: Torque Shift Trans / 4 - 5 Gear Shift Under Hard Acceleration
I have been having an issue with my 4-5 gear shift under hard acceleration and know that a rebuild is due soon but I was wondering if any high performance kit available with all the clutches and friction discs needed to rebuild.
View 6 RepliesFord 6.0L Power Stroke Diesel :: Torque Converter Shutters In 5th?
With my first tow under my belt from this weekend in my new-to-me truck, I quickly learned that my TC shutters in 5th if I hold fuel down enough to bog the truck before it wants to down shift. The shutters are pretty violent as compared to others I've experienced in Explorers and F150s. When do you know it is time to change it out? Or, is there something else I can or should do before changing it?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Torque Converter Lockup Shudder
Anything besides a worn out Torque Converter clutch that might cause the incredible amount of shaking when the transmission tries to lock the TC?
View 6 RepliesFord 6.0L Power Stroke Diesel :: Torque Converter Shudder When Hitting The Brakes
I've done the testing of hitting the brakes when the TC is locked and when it's off the shudder disappears. My question is I recently had a trans flush and both internal and external filters replaced. There was a hint of noise before then but it seems it's getting progressively worse. Could it be that they used the incorrect trans fluid? Reading through it seems as if I should follow the steps of dropping the pan and looking for signs and symptoms and then replace with the correct mercon fluid (if that's not already what's there). Then maybe some additives like shudder fix? I just want to make sure I take the correct steps to solve the problem as to not break the bank getting a new TC put in and missed something cheap and easy. Also reading it could be motor related maybe a misfire so just looking for pinpoint the problem.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Auto Transmission Won't Engaging - Torque Converter Broken?
Before taking to Ford or random trans shop just yet, looking for diagnosis recommendations (or an item or two to replace DIY). Torque converter bolts are broken or TC itself? Solenoid (but would expect a code)?
Issue: Doing 45MPH at the tail end of the 6hr drive, then engine simply revved and coasted to stop. No lurch, pop, noise felt like a manual transmission popped out of gear and into neutral. When the shift to R/D/L/4x4 hi/lo, can feel transmission engage. Engine revs and 'slips' are the best way to describe (no abnormal noise otherwise)I can feel it applying a very slight load (doesn't move, but can feel it try). No warnings/issues leading up to this in the 6yrs and 100k miles I have owned (has 174k miles now). No leaks/visible issues underneath.
Fluid is not burnt, the level is ok. Replaced (no flush) Mercon SP fluid at 125k when bulletproofing. No codes, including hard codes. Trans temp was 165 before/after, which is normal. All engine temps/values on Scanguage normal. SCT tune since bulletproof (though don't abuses it), set back to stock. Also disconnected pos/neg and touched both sets of cables together for several mins.
Ford 6.0L Power Stroke Diesel :: Rough Idle And Jerking / Bucking When Torque Converter Locks Up
So, I was on my way back home driving through the middle of nowhere Utah late at night, when I had an injector tip crack. I was able to identify which one and unplug it so I could get to Grand Junction, CO (about 350 miles away) where I have family. After a power nap I started calling parts stores and found an injector from Advanced Auto Parts (I couldn't find a motorcraft reman, but I was restricted for time). Installed it and all seemed good so I hit the road again. However, nothing changed. It still had the bad miss (rough idle, jerking/bucking when the torque converter locks up) just like when I had the injector unplugged.
The truck is an early 2004 6.0. It's the number 4 injector. I finally got home and hooked up my AE scanner to discover a #4 injector circuit low P0270 code and circuit contribution/balance fault P0272. It's definitely missing because disabling it has no effect. This could be a loose connector at the injector or FICM, because I can't afford another injector right now.
Ford 6.7L Power Stroke Diesel :: 2012 F250 Diesel - Transmission Noise When Shifts Into 5th Gear?
When the truck shifts into 5th gear i instantly feel a constant vibration and noise until it shifts to 6th gear. This happens nearly every time while driving at 40mph. Rpm range 1200 - 2000. I bought the truck new on June 30th and noticed the problem on my way to work on Monday July 2nd. Took it to the dealer on July 5th and the tech said it was the torque converter slipping. I drove it home because they didn't have time to work on it. Took it back on July 12th and the dealer has had it since (currently 30 days) They originally told me it was not the engine or transmission and it was an exhaust problem. Last week they said it was the motor mounts and said they would be done.
View 14 RepliesFord F-150 (2004-2008) :: 2007 - Up / Down Shifts Randomly After New Torque Converter
I bought an 07 F150 5.4 4x4 with 135k on it about 6 months ago. Shortly after buying the truck I began experiencing a shudder when lightly accelerating up a hill. Also when accelerating hard it would misfire. Thinking that it was plugs or COPs I changed the plugs and coils. That fixed the missfire issue but it still shuddered when accelerating up a hill.
I decided to take it back to the used car dealer where I bought it so they could fix it. On the way there the fly wheel broke. The dealer replaced it and thought that it was the cause of the problem but on the way home I still experienced the shudder. I took it back and they "scoped" it and found that the torque converter was bad. They replaced the TC and now there is no more shudder BUT now I have a new problem.
Now if I am driving at highway speed and let off the gas it feels like it immediately down shifts for a few seconds then shifts back up and coasts along until I give it gas again. There is enough resistance that it feels like a jake brake or that the breaks are being applied. Also if driving along at 30 - 40 mph and just holding the gas in the same spot maintaining 30-40 it feels like it down shifts and up shifts over and over until I either give it more gas or let off all together. Also a few times pulling away from a stop I will get a thump.
I have an appointment with a transmission shop in a few days but today on the way home I put it in second gear while going up a hill so it would not shift and it seemed like it was coughing and sputtering. So now I am wondering if that is what is happening and either feeling like or causing the down shift up shift issue.
If it is a missfire issue why would the new torque converter cause this? It has all new motor craft plugs and all new after market coils.
There are no check engine or other warning lights lit on the dash. I have a cheap ODB scanner and it shows two codes. B1676 which apparently is a Battery Pack Voltage Out Of Range or ABS voltage issue. The voltage is showing at 14.2 volts and there is no noticeable battery issues. The second code is a P1000 Drive cycle test not complete. (this code has been showing for some time the 1676 code is new since the torque converter swap)
One side note: after the TC change every time I start the truck the radio/cd changer cycles though all the CDs. like it it is checking for a disk so it clicks and pops around from a moment. The only time I heard this happen before was after having the battery disconnected. The clock is not reset though like I would expect if it was losing all power.
Ford Aerostar :: 1987 - Draining Trans Fluid From Torque Converter?
How to drain the tranny fluid from the torque converter , I am dropping the pan and installing new filter and fluid, I want to get as much of old fluid out as i can It has a 3.0 engine with overdrive...
View 11 RepliesFord Transmission :: 2000 F250 7.3 - Trans Slipping - Torque Converter?
I was driving my 7.3 down the road and it started acting like the trans was slipping, it revved up and tried kicking down a couple times and when I slowed down and went to speed back up it just had no power coming through the trans to the wheels it just revved. I put it in neutral and it idled up for about 5 seconds. I put it in park n shut it down. I fired it back up after looking everything over and it moved about half mile down the road and no power to the wheels again. The trans is full of fluid, is there a sensor that could of went bad or just the torque converter or the entire thing shot? Only owned my truck 6 months has a trans and motor swap already from previous owner. 180k on current motor n Trans. 382k on my truck. t6 4" turbo back banks exhaust only mods I know of.
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Transmission Shifts Hard To A Lower Gear
I currently have a 2006 F-250 6.0 with 187,XXX.
My problem that i am having is that the transmission recently within a couple weeks started acting weird about the same time 3 of my fuel injectors started failing. When i start up the truck and put it into drive it takes about 3-5 seconds to shift. Once it's in drive it runs pretty well but it will start shifting out of normal when i go to accelerate. Also when i go to slow down sometime the transmission shifts hard to a lower gear. I also have a video of the sound that it had started to make since its hard to describe.
Here are attached videos and photos. I want to hopefully fix the problems myself so i can learn more about my truck. I am going to handle the fuel injectors here soon since 2 are failing and ones about to these have been causing the truck to shudder at around 47-53 mph but after that its fine.
The transmission is stocked and never been altered, i do admit for 3-4 years I have changed the fluids or filters.
The truck is bullet proofed, sct tuner, upgraded turbo from stock, 4" exhaust, head studs and new everything when the engine was rebuilt and bulletproofed.
I plan on going to ford tmw to have them figure out the problem and hopefully its just solenoids so i can fix it myself. I have a link posted also where you can hear the noise it has been making when in R P and when shifting going down the road and it is a automatic.
YouTube.....
Ford 6.0L Power Stroke Diesel :: 2003 Excursion - Trans Would Not Budge In Any Gear
After doing some hunting/wheeling with my son, got back to town and 2003 Excursion w/ ~145K miles would not budge in any gear. No codes with Scangage. After 30 minutes I finally thought to rev it up and it shifted hard into gear, and drove normal home. What do do now?
View 4 RepliesFord 6.0L Power Stroke Diesel :: Stuck In 3rd Gear After Trans Swap With 10 Codes
Bought truck for cheaper price with no 3rd gear. Went to a reputable yard and picked up a cheaper trans... It was carfaxed with 185K miles and in a rollover. (This is the last time I try to save a couple bucks by getting a cheaper transmission.)
I believe trans is stuck in 3rd gear...Takes off slow. RPMs do not drop..Doesn't shift...Feels like I'm in 3rd from takeoff. Here are the codes:
P2262: Turbo / Super Charger Boost Pressure Not Detected Mechanical
P2614: Camshaft position signal output circuit / open
P2262 again
P1000 On board diagnostics II Monitor / drive cycle test not complete
P0678 Cylinder 8 glow plug circuit
P0672 cylinder 2 glow plug circuit
P0603 Internal control module keep alive memory malfunction
P0720 output shaft speed sensor circuit
B1676 Battery pack voltage out of range
B1318 Battery voltage low
Ford 6.7L Power Stroke Diesel :: 2012 F350 - Trans Would Not Shift Into 6th Gear
My Father In-law has a 2012 f-350 Dually with 4K miles. He tows a 9K lb camper and until our last trip the truck ram flawlessly. On our return from Myrtle Beach to central NC we were on a freeway traveling at 63 MPH and his tranny would not shift into 6th gear. Tow haul was on. There was some headwind (10MPH) but no large grades or any reason we can think of not to allow an up shift. His display did show a countdown to empty of the exhaust fluid 450 miles to empty.
He took the truck in for service and no codes were found. Dealer did not find any TSB's addressing the tranny issues. Is the sixth gear up shift in tow haul set very conservative? Does it hold 5th unless the load is below a certain value? Other trips we have been on have been mountain towing so 6th gear shift would have been on down hill or level sections. Dealer wants us to bring it to them when it won't up shift next time but dealer is not along a freeway.
Lexus ES 2007-12 :: No Power And Stays In 1st Gear All The Way Up To 4000 Rpm Then Shifts
ES350 Transmission - I have the following issue that has happened to me twice now.
When it's cold outside (around -10C or below), I start the car and let it run for about 1 minute. I pull out of the parking lot and drive down the street for a very short distance and stop at the intersection and wait to turn left. This only happens when I wait for a minute or more. I go to turn left and the car feels like it has no power and stays in 1st gear all the way up to 4000 rpm and then shifts. After this the car is totally fine and it shifts at the normal 1500 rpm or so going about 15km/hr. When I'm sitting at the intersection waiting to turn, the car is idling at about 1200 rpm or so while the car is warming up.
I've tried many times to recreate the issue but I couldn't do it because I never let the car sit and idle. If it's constantly moving with stop and go it's fine.
I called the Lexus dealer to ask about this and they told me the first thing to do is change the transmission fluid because it could be low or dirty. The car is 6 1/2 years old (July 2006) with 58,000km on it. They said the transmission fluid should be changed at the 6 year interval. They also asked me if I had the car in the shift manual mode (which I didn't) because it seemed to exhibit this behaviour.
Ford 6.7L Power Stroke Diesel :: 2015 F250 - Engine Begins To Rev Up And Speed Increases But Trans Stuck In 2nd Gear
2015 F250 with 6r140 Transmission. I have 13 K miles on my truck. While pulling my Travel trailer up a hill the transmission kicks down thru the gears, which is fine, but as I crest the hill and in 2nd gear, the engine begins to rev up and the speed increases, the transmission will not automatically go into 3rd gear. I have tried to let up on the gas pedal, but it remains stuck in 2nd gear. I have to shift to manual and then put it in 3rd gear. Then it shifts up as it should. I have tried with the transmission in "TOW' and not in "TOW". I have even tried it in "Cruise Control". Ford dealership ran tests but could find no problem. However it was road tested without the trailer.
View 5 Replies