Golf IV R32 :: Valve Cover And Intake Manifold Torque Specs
I have to replace the valve cover gasket this weekend.
View 5 RepliesCamry :: Found Torque Specs For Oil Plug
I had found the torque specs for the oil plug, oil filter housing the oil filter housing drain plug but I am unable to locate now.
30 ft lb drain plug
25 ft lb filter housing
10 ft lb filter housing drain plug
Ford F-150 (2004-2008) :: Tie Rod End Torque Specs?
Just doing the bro in law's tie rod ends and we are wondering what torque we should be putting on the castle nuts? They are greasable Moogs...
View 2 RepliesLexus RX 2010-15 :: Torque Specs For The Caliper Bracket Bolt?
2011 Lexus RX350 ... What are the Torque specs for the caliper bracket bolts (front and rear caliper brackets) a pdf will be great
View 1 RepliesFord F-150 - 1997-2003 :: 1999 - Driveshaft Bolt Torque Specs
What the torque spec is for the driveshaft to rear differential flange mounting bolts on the 99 F150 4x4 supercab?
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Torque Specs For Tie Rods?
What are the torque specs for tie rods for a 4x4.
View 4 RepliesFord F-150 - 1997-2003 :: 1999 - Front Hub Assembly Torque Specs?
Tell me the torque specs for the various attaching nuts of the front hub assembly for the 99 F150 4x4 5.4L (large nut on the spindle, mounting bolts to back of spindle, etc if any) ? I will need them to put everything back together after checking the tone ring for my ABS problem.
View 1 RepliesFord Super Duty (1999-2016) :: 2012 F350 6.7l - EGR System Torque Specs
Replacing EGR cooler/ EGR valve. Are there torque specs going back together with the EGR system? or is there a forum that has all the torque specs id need to complete the job.
View 4 RepliesFord 6.7L Power Stroke Diesel :: Torque Specs For Front And Back Rancho 9000XL?
What are the torque specs for front and back rancho 9000xl? Really want to know the front top spec with the rubber bushings that squish flat the most.The rest ill make tight.
View 14 RepliesFord F-150 (2009-2014) :: 2012 - Mounting New Shocks - Torque Specs For Upper And Lower Bolts?
Mounting the shock with the boot up or down? I know it doesn't matter according to Bilstein but one way has to be better than the other.
Second. What are the torque specs for the upper and lower bolts? I know the lower front is around 350lbs but haven't found anything for the rest. found out the rear bolts are torqued to 66lb.
Third. The front shocks didn't come with a boot to protect the shaft. Is one needed when the shock is installed?
Truck is a 2012 F150 FX4.
Ford 7.3L Power Stroke (1999-2003) :: Water Pump Lower Elbow Bolts Torque Specs
I read 18lbs for the water pump but it took a cheater bar (perhaps due to corrosion) to get the water pump lower elbow bolts off.
On reinstallation, what should the lower elbow bolts be torqued to? Checked the sticky (Ziggy's Torque Specs) but didn't see the specs for this item.
Ford Super Duty (1999-2016) :: 2005 - Torque Specs For Crankshaft / Cylinder Heads And Camshafts?
What are the torque specs for the crankshaft,cylinder heads and camshafts for a 2005 f550 v10 6.8?
View 2 RepliesFord Brakes/Suspension :: 1969 F100 Steering Coupling / How To Get Flange Off In Order To Remove The Bearing
I'm attempting to replace the steering coupling in my 1969 f100 2 wheel drive 240 6 cyl.. I have found that the lower column shaft bearing needs to be replaced also. My problem is that I cannot figure out how to get the shaft coupling flange off the shaft in order to remove the bearing. Also if I do get it off how do I remove the old bearing?
View 2 RepliesFord Exhaust :: Torque Specs On Exhaust System?
Just put on a 4" MBRP turbo back system. What torgue should I tighten the clamp bolts?
View 2 RepliesGolf IV / Jetta IV :: Bearing Noise After Bearing And Transmission Replaced?
I replaced all the bearings and put in a rebuilt transmission and still have bearing like noise , seems like the front, directly increasing with speed . Same in neutral, no change with turning or breaking. Getting worse over the past few months.
View 1 RepliesGolf IV R32 :: Suspension Clunking - Strut Caps Raised A Little Under Load
Installed fk coils about 5k miles ago. I replaced the strut mounts and the bearing with new oem. I am not "slammed" by any means but a very mild drop. I noticed the strut caps are raised a little under load, can this be the cause of the clunking sound? The strut cap going down on bumps etc? Or could the strut mounts have already failed. Seems a bit premature to me. I guess I'll have to take it apart and take a peek.
View 2 RepliesGolf IV / Jetta IV :: Coilover Caps Are Sticking Out And Hitting Hood
I bought some coilover for my mk4 Jetta, and the two front coilover just don't seem write, they are sticking way to much from where they need to be at, and they are hitting my hood..
View 24 RepliesGolf IV / Jetta IV :: Door Malfunction - Needs To Be Pushed In Order To Open
when unlocking the car, half of the time the passenger front and back door do not open from the outside even though the little door opening/closing pin has jumped up into the open position. then i need to give the door a good push near the lock , i can hear a little click and then the door opens.
how to fix this?
Golf IV / Jetta IV :: Can't Move The Seat In Order To Remove Center Console
Completely stock, no swap. No motor noise when I click the buttons on forward, back, up or down. Nothing. Everything looks connected under the seat but not entirely sure. Fuse 1 and 44 are good on the side of the dash. This is for a 2003 Wagon with GLX interior and most upgrades from the factory. I need to move the seat in order to remove the center console/radio cage as it's blocking the armrest nut.
View 1 Replies