Ford Transmission :: Hard Shift And Clunk When Shifting To Reverse
I just recently bought a 95 F150 with a 351. The truck has high mileage, about 190k, and I am not sure how long the transmission has left. It rides smooth down the road, but when I put the truck into reverse it hesitates for a moment then makes a loud clunking sound(as if a door is being slammed) and then jerks into gear. The reverse works great at the moment though. Should I be worried, is there anything I can do to fix this?
View 11 RepliesLS / MKZ :: Transmission Is Sporadically Shifting Hard When Car Is Cold
2002 LS-V8 230k miles.
Recently, I'm noticing that when the car is cold, the transmission is sporadically shifting hard. Sometimes from P to R it kicks into gear hard. From R to D the same thing. Whenever I shift to to N first, and then go to R or D it never happens.
Ford 6.7L Power Stroke Diesel :: 6r140 - Transmission Slams Hard Into Reverse / Shifting From 1 To 3 Is Awful
I'm having problems with my 6r140 in my 2011, the truck is an early build around 8/2010 I believe.
After cold soak when shifting into reverse after allowing engine to warm a bit the transmission almost always slams hard into reverse.
After that shifting from 1-3 is awful, the transmission will try to go into 3rd but downshift to 1st then fail to go back into 3rd multiple times. This situation is extremely dangerous when trying to pull into traffic.
Oh and once the transmission gets into 3rd it will skip 4th and go right into 5th. There is only 94k miles on this transmission/truck.
I just bought this truck about a month ago, does this sound like an issue with the solenoids in the valve body?
I'm very mechanically inclined and can swap them if need be but now we're talking few hundred in solenoids and then getting the trucks pcm flashed right?
Also fluid has been changed and I used mercon lv.
Golf IV R32 :: Hard To Get In Reverse And Shifting From 1st To 2nd Is Very Rough
Lately my R is acting up, sometimes hard to get in reverse and shifting from 1st to 2nd is very rough. I looked at the cables , the left one towards the engine , the rubber bushings seems to be broken, lots of wiggle in there, is that enough to cause this? Is there any adjustments needed on the cables anyways?
View 9 RepliesElantra MD (2010-15) :: Transmission Slips From Cold Start / Shifting Hard From 1st To 2nd Gears
I've had 2 Elantra 2012 models 1 a gls the second a limited. As far as transmission issues both Elantra's from a cold start after allowing RPM's to idle down before taking off they both have started shifting hard going from 1st to second gear 1st car was around 8-9 k miles now 2nd started at 3 k miles. Since owning 2 cars same make same year same transmission and many times to dealer 1st car ended with Transmission replaced 2nd has now started doing the same thing they reset adaptive and next day did it again its now back at dealer waiting for them to diagnose again.
View 13 RepliesGolf IV / Jetta IV :: Fails To Go Into Reverse When Transmission Is Cold
I recently purchased a 2002 Jetta VR6 GLX. It drives fine when the transmission is warm, but fails to go into reverse and has a hard time shifting out of first when it's cold. I took it to my german mechanic friend who specializes in transmissions and he said that both the valve body and transmission need to be replaced. Problem is I don't have the funds to replace both.
The current transmission has 131000 on it.
Golf IV / Jetta IV :: 2001 - Transmission Has Hard Time Going Into 1st And Reverse / Rough Idle
2001 VW Jetta 1.8t automatic.
Transmission has a hard time going into 1st and reverse. Also some times hits hard going into third. I have a CEL for a vehicle speed sensor? Was wondering if it's not the VSS but maybe one of the other tranny sensors?
Separate question. Same car has a rough idle issue. Occasionally stalls but intermittently runs normal always has a low idle around 600 rpm. I have a code for an injector on cylinder three.
VSS code : P0725 - engine speed sensor circuit malfunction
Injector code : P0203 - injector circuit open cyl 3
Golf IV / Jetta IV :: After Changing Transmission Fluid Hard To Shift Out Of Gears On Cold Starts
So I changed transmission fluid on my 1.8t GLS because I was having difficulty shifting out of gears on cold starts. It seemed to work fine for a few days and now I'm back to square one, it still doesn't want to shift correctly!
View 14 RepliesCamry :: 2004 Clunks Very Hard When Shifting Into Reverse
I have a 2004 Camry 4cyl with and Automatic Transmission. 193,xxx miles. I bought the car with 165,xxx miles. From time to time the transmission would take a little longer than normal to shift from 1-2 or 2-3. It has also had an issue with locking up the torque converter at speeds around 50 MPH which seems to bog the engine some. An adjustment of the foot on the gas pedal fixed both of these problems. (I just let up a little or pressed a little harder)
Well on friday it did something weird. It now clunks very hard when shifting into reverse. Also when in drive it seems to be in 3rd gear. The engine revs very high before the car starts moving but then it seems to run fine once moving and up to road speed.
I have heard that the Transmission may be controlled by its own Computer unit. Is that true? How do I get codes from it?
I have run my scan tool through the OBDII port and get no codes at all.
Accent LC (2000-05) :: Overheating Constantly - Car Won't Go In Reverse And Has Hard Time Shifting Sometimes
I have a 2003 Accent and it has been over heating constantly for about 5 months. After it started, we replaced the main radiator hose, thermostat, radiator cap AND a head and head gasket. It worked for about 2 weeks and then over heated again. It seems like there is too much pressure somewhere because the lid for my reservoir shoots off and all the coolant comes out. I'm just not sure where to look for a clog since it is coming out of the reservoir. It also recently started having transmission problems(?) or that is what I think it is... It won't go in reverse and has a hard time shifting sometimes. I'm not sure if it could be related or if it is the tranny also.
View 4 RepliesSanta FE SM (2001-06) :: 2004 - Hard Thump When Shifting From Reverse Into Drive
Recently my 2004 Santa Fe 2.7 AWD (~86k miles) has started to give a sort of hard thump when shifting from reverse into drive. It's fine going into any other gears and it shifts up and down normally. If I shift from reverse to neutral and then to drive it's fine.
I changed the transmission fluid when we first got the car at 40K miles with Hyundai Liquid Unobtanium SPiii fluid and again at 80k miles with Valvoline's SPiii offering. I just checked the transmission fluid level and it's within the normal range.
I can't tell if this is just drive-line slop or something else inside the tranny.
Honda - Fit :: 2008 - Knocking Noise In Engine / Hard Time Shifting Into Reverse
[URL] .... My engine has been making this sound for a while now I am at 125000 miles, what it could be and if i need to be worried about it? also, possibly unrelated, it has a SUPER hard time shifting into reverse, it gets stuck and it feels just super sticky shifting in and out of reverse. Sometimes I can't even get it to go into reverse without letting the car roll a bit. Also, at around 3k rpm the engine sounds a little grinder in any gear. 2008 Honda Fit Sport ...
View 19 RepliesFord Transmission :: Shifting Hard From 1st To 2nd?
bought the truck about 3 weeks ago and still having problems with the transmission. Replaced the VSS and it didn't work. My problems are it shifting hard from 1st to 2nd, it feels like it falls out of gear ( i can floor it and the speedometer creeps up then shifts hard.) Now i read having the 3rd brake light out is a problem with the trans too, my 3rd brake light is out along with the interior dome light ( doesn't go on when doors open) i plan to replace the TRS on the tranny tmw is there anything else i can do? how do i solve the brake light problem?
View 14 RepliesImpala - Chevrolet :: Transmission Slipping When Shifting From Reverse To Drive
2007 Chevy Impala3.5L 6-cyl Flex Fuel engine w/ 4 speed auto trans52,800 miles
Extreme driving conditions maintenance schedule kept.Transmission standard service done @ 32,800 miles which was 20k ago.
PROBLEM:
1) Twice in past three days, when shifting from reverse to drive the transmission has slipped, revving hard with rpms spiked above 3,000 for about 2 seconds before engaging the forward drive gear.
Normally I come to a complete stop of all reverse motion with foot fully on the brake pedal before shifting. Admittedly, I got sloppy the first time noted and still had very slight reverse motion when I shifted.
2) Several times late today, while driving uphill at approx 35 - 45 mph, when the car downshifted there was an extremely brief moment of transmission slippage with spiked rpms. It was so brief each time that at first I thought I'd imagined it until it happened again. Then it did it once on a level surface in a parking lot when having shifted from reverse to drive without problem and was gently accelerating the transmission again slipped for just the briefest moment when the normal automatic shift point was reached. So far, all incidences while driving have been so extremely brief that it was the merest hint of a hiccup.
3) When bringing the car to a complete stop, such as at a stoplight or when parking, as the transmission automatically shifts for the braking of speed, sometimes there is a minor but noticeable thunk sound seeming to come from underneath the car, I'd judge to be somewhere about under the level of the dashboard or slightly forward of that. Could that be from a worn or broken transmission mount? And, if so, could that be somehow causing the slippage problem?
4) This transmission has always, even since new, allowed more roll after being shifted into park, the engine shut off and my foot taken off the brake than any other car I have ever driven. If I forget to engage the parking brake quite tightly, the car will roll forward quite a few inches before the parking pawl holds it, even on the level. I've been told both by the dealership shop and the independent mechanic shop that there is no problem and that this particular engine/transmission combination tends to do this although my particular car seems to do so somewhat worse than average.
ACTIONS TAKEN SO FAR:
1) Have made an appointment to take the car into the mechanic.
2) Will check the transmission fluid level per instructions in the owner's manual tomorrow when I have daylight to see what the fluid level and color on the stick looks like.
NOTE:
1) I periodically check the transmission fluid level and it has never been low or discolored. The shop checked it for me, along with making sure everything else was road trip worthy, for an emergency 1,000 round trip in late November, just three months ago. No problems then.
2) No evidence on the garage floor of any leakage. Garage floor is dry.
QUESTIONS:
1) I presume the first step is for the mechanic to check the fluid level and examine for any leaks?
2) If the mechanic cannot duplicate the problem in a test drive, then what?
3) If the problem cannot be duplicated and no apparent cause found, I presume that the prudent course of action is to go ahead and have standard transmission maintenance done (i.e. drop the pan, check for debris, drain and replace with fresh fluid) then see if that halts the slippages?
4) Given that this car has already had failures of the power steering pump, water pump, and part of the wiring harness, and has a fuel pump starting to get noisy, despite aggressively maintaining all standard/preventive maintenance, that perhaps it is time to think of replacing this car, especially if there proves to be any truly major transmission problem found?
Passat (B6) :: Transmission Having Delayed Engagement When Shifting Into Reverse And Drive
I bought my '07 Passat 2.0T Wagon as a CPOVW 6 weeks ago. It had 4700 miles on it. I complained about the transmission having a delayed engagement when shifting into reverse and drive. (it drives normally however with positive shifts and is very enjoyable) I was told it was normal and not to worry. (could it be designed-in to soften the engagement?).
This week I noticed a light "thunk" in the right front when re-applying power while coasting below 40 MPH. I never noticed it before but I usually strive for smooth driving so that may be why. I've had other Aisin Warners but they were in Volvos. I got out of a '99 Volvo Cross Country because I didn't trust the driveline. Am I going down the same road?
Ford Transmission :: E4OD Shifting Into Reverse And Drive A Bit Clunky
I have a 94 E350 with the 460 and the E4OD trans. that has only 30K on it.
Last weekend I took it on a 250 mile trip (one way) and it ran beautiful until the final steep hill to our vacation house. It started vibrating when it went to down shift and wouldn't pick up any speed, the OD off light was blinking. When I pushed the OD button and it cleared right up. Ran beautiful until I tried to climb that same hill again (same thing happened). It showed the same symptom when I tried to back up a steep driveway during the same trip.
Now it no longer does the vibrating but now has harsh/firm up shifts. Downshifts are smooth though, but shifting into reverse and drive are bit clunky too.
The codes I pulled were KOEO 212 and 668. After I erased the codes the 668 didn't come back. But I did change the MLPS to the new updated one from Ford and its still doing it.
I also found the 40amp mega fuse under the hood was blown too, related? Could a 1/2 qt over filled trans. cause this now too? In NH I added some fluid thinking it was low because I could not get a clear reading on the dipstick but I think the level was up there.
Ford Transmission :: Hard Shifting From 1st To 2nd Gear
Have a 2000 expedition with 84,000 miles. Tranny seems to shift hard from first to second gear. Its been 24,000 miles since my last dealer tranny service. Thinking of getting a new service now before the recommended 30,000 manual recommendation. Whats happening?
View 6 RepliesFord - Explorer :: 2006 - Shifting Hard Into Reverse At First Then Stuck In High Gear Or Slipping - OBD2 Codes
Tranny started acting funny recently...shifting hard into reverse at first, then last night it was like it was stuck in high gear or slipping on the way home. Limped it home and took the following codes:
P0743 TORQUE CONVERTER CIRCUIT ELECTRICAL
P0750 SHIFT SOLENOID A MALFUNCTION
P0755 SHIFT SOLENOID B MALFUNCTION
P0760 SHIFT SOLENOID C MALFUNCTION
P0765 SHIFT SOLENOID D MALFUNCTION
P0962 PRESSURE CONTROL SOLENOID A CONTROL CIRCUIT LOW
P0966 PRESSURE CONTROL SOLENOID B CONTROL CIRCUIT LOW
P0970 PRESSURE CONTROL SOLENOID C CONTROL CIRCTUT LOW
Mazda - Mazda3 :: Reverse Gear Wasn't Shifting Properly - Low Transmission Oil
Took my car in for oil/filter change and in some odd circumstance, the young mechanic managed to drain 1 liter of transmission oil out of my car (which I didn't know at the time). After driving for 10 minutes (~5 km), I noticed my reverse gear wasn't shifting properly. After ~30 minutes of driving, my car was smoking from the exhaust pipe (turns out he had overfilled my engine oil too!!). Took the car back in to complain the mechanic supervisor claims my transmission is still fine and all I need to do is refill the lost fluid. Another independent mechanic later tells me my transmission line is likely fried if I had experienced what I did, and those guys should be responsible to replace everything. Since fluids have been topped up, I have no proof of who is right. So my question is, if I only drove for maximum 50 km after my transmission fluid was drained and engine oil overfilled, would that be enough to cause serious damage to the car?
View 10 Replies