Honda - Fit :: 2008 - Knocking Noise In Engine / Hard Time Shifting Into Reverse
[URL] .... My engine has been making this sound for a while now I am at 125000 miles, what it could be and if i need to be worried about it? also, possibly unrelated, it has a SUPER hard time shifting into reverse, it gets stuck and it feels just super sticky shifting in and out of reverse. Sometimes I can't even get it to go into reverse without letting the car roll a bit. Also, at around 3k rpm the engine sounds a little grinder in any gear. 2008 Honda Fit Sport ...
View 19 RepliesAccent LC (2000-05) :: Hard Time Getting Uphill
This isn't my car, but It is my grandparents and I drive it often to my doctors 80 miles away, and to meetings 100 miles away. Both directions are very hilly and one of the road has 3 mile inclines. 2005 Hatch, Automatic.
Fresh spark plugs, oil change, oil filter, air filter. 95k miles.
Gas mileage is ok, but it has a really hard time getting up hill. I will be almost pedal to the floor going up the hill for 3 miles at 3k RPM.
Is this something I should be turning OD off for? I checked the manual and OD wasn't mentioned in the glossary.
Accent LC (2000-05) :: Hard Shifting Between Gears And Wouldn't Go Over 45
That said my wife bought a 2001 Accent 1.6L Auto while I was overseas and it's been a great car, about 8 days ago it just crapped out. The reverse went out on her so we took it to get the codes read and on the way it went in limp mode, started hard shifting between gears and wouldn't go over 45 she says. Took it in to the stealership today and they said that the trans is shot as well as showing codes for P1527, P0732, and P0734. I know what the two slippage codes are and I can prolly just replace the speed sensors and that will be fixed but I'm not sure about the reverse and P1527.
View 4 RepliesAccent LC (2000-05) :: 2001 GL Transmission Shifting Hard Into Drive
I have a 2001 hyundai accent GL the transmission has started shifting hard when it shifts into drive. It shifts fine and smooth from first to second but when it shifts into drive it hits drive hard and sometimes it acts like it doesn't want to shift and if you let up on the gas it will go ahead and shift, but when it shifts to overdrive it seems fine but hits hard when it down shifts back to drive. Also I have noticed a couple times when it goes to shift into drive the engine seems like it revs up some but when you let off the gas it goes ahead and shifts.
View 3 RepliesAccent LC (2000-05) :: 2002 - Hard Shifting Into 2nd Gear (Automatic)
The Accent has been working great recently until the other day when I got in to go to work and now it suddenly shifts very hard into 2nd. And sometimes 3rd.
This problem seems to come and go. Sometimes it will shift smoothly. Other times it will have to reach super high rpm and I will have to let off the gas and slowly accelerate to get it to shift. This seems to happen throughout all the gears and it does not make any difference if overdrive is turned on or off. Also reverse works just fine.
I checked the fluid and it is at the proper level. It does seem to be a little dirty (not burnt) so I am planning on changing the transmission fluid, but something tells me that is not going to solve this issue. It seems like an electrical issue to me. What it could be?
There are no codes at all on the car. Don't know if it matters but the car just turned over to 100k miles. I've been reading on here about all the problems the automatic trannys have in this car but 100k seems a bit early to have any serious transmission problems.
Accent LC (2000-05) :: Light Clunk When Shifting Into Reverse - AT Fluid Has Burnt Smell And Color
I bought a 2005 Accent with 150k one year ago and 3 months ago got AT fluid and filter changed. Color was very dark my mechanic friend said.
I checked the fluid and after just 3 months light driving, noticed it smelled burnt and so just changed it again yesterday and it was very dark.
Another piece of info is that previously when got the fluid changed 3 months ago the level registered way above high when car was off but then then normal when running in N. Same thing is happening now. My knowledgeable mechanic friend just told me to keep my eye on it.
There are no shifting issues, except for just light clunk when shifting into Reverse, but other than that it's great.
I just want to know what problems might be going on to burn the fluid so fast and have strange level readings when car is off but okay when on. I read some stuff about solenoids but because shifting is great should I even consider that?
Accent LC (2000-05) :: 2004 - No Reverse / Shifts Hard Into Drive
2004 accent had a drink spill on lower console, and think this is why it quit shifting? Disassembled, cleaned switches, unhooked battery, and car still has no reverse, shifts HARD into drive, will not move further.
View 5 RepliesAccent LC (2000-05) :: 2004 - Clutch Lost All Resistance / Hard To Get Into Reverse
I'm not very mechanical when it comes to cars. I have never had any clutch issue with my car. I arrived to work yesterday fine. When I started to leave it was incredibly hard to get into reverse and I had to force shifting after I left and the clutch had also lost all resistance and I could easily push it all the way to the ground. What could be a cause of the clutch always working perfect including the last time you drove it, and then 8 hours later you start up and it has done a 180. The fluid level is fine. I would presume if my clutch had went I have have slowly noticed it going.
View 1 RepliesCavalier :: Clunk When Shifting Into Reverse Doesn't Happen All The Time
I just had the motor torque and strut mount fixed and was told that I have an exhaust leak flex pipe. My problem is I'm still getting a clunk when shifting into reverse doesn't happen all the time but it is concerning plan to have flexpipe fixed in the near future. will that take care of the clunking sound or is it something else? don't have a lot of cash to work with right now.
View 1 RepliesToyota - Corolla :: 1994 - Hard Time Shifting Between 20 - 30 Mph
My 94 Toyota Corolla has about 190,000 miles on it and lately it has had a hard time shifting between 20-30mph. It finally does reach it and does not have trouble shifting at any other speeds. This only happens in the heat of the afternoon (Never have this problem in the morning). Also, my O/D light has been flashing when this happens, or at least around the time it happens. Could these two problems be linked? I took it to my mechanic in the morning and he checked the transmission fluid and it seemed fine, he also had no problems driving around when he tested the car. He said my transmission is going and that I should make "long term" plans. Is there any hope?
View 1 RepliesPassat (B6) :: Hard Time Shifting Fast From 1st To 2nd When Accelerating
Was having a hard time shifting fast from 1st to 2nd when accelerating hard, it was like something was blocking the 2nd gear gate, same thing sometimes when downshifing fast from 6th to 5th.
After JT recommending it here, I installed the Neuspeed torque arm insert. Used a scissor jack on the left front side (it has a wide base), got under the car from the front bumper passenger side. 21mm bolt was tight, but got it out with a regular length 1/2 inch socket bar. Insert was hard to get in (even after spraying silicone on it), finally just sprayed silicone into the existing bushing and the insert slipped right in.
First test drive really made it easy to shift from 1st to 2nd under hard acceleration only a slight bump when entering the 2nd gear gate, downshifing was smooth too. Down side? none that I noticed, no vibration.
Golf IV R32 :: Hard To Get In Reverse And Shifting From 1st To 2nd Is Very Rough
Lately my R is acting up, sometimes hard to get in reverse and shifting from 1st to 2nd is very rough. I looked at the cables , the left one towards the engine , the rubber bushings seems to be broken, lots of wiggle in there, is that enough to cause this? Is there any adjustments needed on the cables anyways?
View 9 RepliesExplorer :: 2000 - Overheating And Air Conditioner Went Out At Same Time
My Explorer has been overheating for the last couple of days. It red-lines unless I turn on the heater, and then it still runs pretty hot. From all I can tell, there is plenty of coolant in it, and the fan is running.
The air conditioner went out about the same time (it goes in and out), but that may just need to be recharged.
Camry :: 2004 Clunks Very Hard When Shifting Into Reverse
I have a 2004 Camry 4cyl with and Automatic Transmission. 193,xxx miles. I bought the car with 165,xxx miles. From time to time the transmission would take a little longer than normal to shift from 1-2 or 2-3. It has also had an issue with locking up the torque converter at speeds around 50 MPH which seems to bog the engine some. An adjustment of the foot on the gas pedal fixed both of these problems. (I just let up a little or pressed a little harder)
Well on friday it did something weird. It now clunks very hard when shifting into reverse. Also when in drive it seems to be in 3rd gear. The engine revs very high before the car starts moving but then it seems to run fine once moving and up to road speed.
I have heard that the Transmission may be controlled by its own Computer unit. Is that true? How do I get codes from it?
I have run my scan tool through the OBDII port and get no codes at all.
Golf/GTI VI :: Hard Shifting Into Reverse When Transmission Is Cold
Noticed that the transmission is cold (ie. sits overnight) it is hard, sometimes impossible, to shift into reverse. Specs on my gti: 14k miles, pretty much stock, manual trans...
View 1 RepliesSubaru - Forester :: 2003 - Hard Time Shifting Into 2nd And When It Does (at About 40MPH) It Jolts
I bought my 2003 Forester a year ago from a friend with 90,000. I love this car, I put a new timing belt on it and off we went. The car worked fantastically from January to August 2011. One night I was driving to watch a show and rather then shifting into gear, it jolted. Pulled over, checked fluids and so on, car worked normally for a while. It started doing this more frequently. It has a hard time shifting into 2nd and when it does, (at about 40MPH) it jolts and same thing for third and so on. I took it to my mechanic but it never misbehaved for him sop I took it back and drove some more and dropped it off at a transmission shops. They get it to do what it does, ran many tests, decided it was the throttle sensor, replaced it, car worked great for two weeks and then reverted back to this behavior. Took it in again three times but they can't seem to figure it out. Anyway, I have taken the car to five different mechanics and no one can quite figure it out. So my car, the Diva, as I like to refer to her, continues to jolt to shift gears. If I put it into reverse it will shift normally until I stop again or slow way down. I am stumped and sad because I love my car. It now has 101,000 and I want it to be kind to me.
View 5 RepliesFord Transmission :: Hard Shift And Clunk When Shifting To Reverse
I just recently bought a 95 F150 with a 351. The truck has high mileage, about 190k, and I am not sure how long the transmission has left. It rides smooth down the road, but when I put the truck into reverse it hesitates for a moment then makes a loud clunking sound(as if a door is being slammed) and then jerks into gear. The reverse works great at the moment though. Should I be worried, is there anything I can do to fix this?
View 11 RepliesAccent LC (2000-05) :: 2002 - Hazards / Dash Lights / Radio And Clock All Constantly Flashing On And Off Repeatedly
I'm having an electrical problem that's resulting in the hazards, dash lights, radio and clock all constantly flashing on and off repeatedly. The car starts fine.
When investigating under the hood, I found a wire (pictures below) that wasn't connected to anything. I'm not sure if this is what's causing the problem, but I figured this was a good place to start.
What this wire is supposed to be attached to, and if it has anything to do with the flashing lights I'm experiencing?
What this wire is or possible causes of these flashing lights.
Ford Excursion :: Transmission Leak / Hard Time When Try To Reverse
I've seen this talked about before and it's happened to me before as well but now the tranny is leaking onto my Ypipe a couple times per week and it's giving me a hard time when I try to reverse. revs drop and it stalls if I don't give it enough gas.
So I know I have to change the seal but Ford is telling me the torque converter will need to be replaced but another transmission shop told me once the seal is changed and fluid level set appropriately I shouldn't have the reversing problem anymore?
Is this something I could attempt myself... looks almost like I'd have to move the exhaust to drop the tranny...