Lexus GS 2006-11 :: Check Engine And VSC Light On - Car Wasn't Shifting Properly
I have 2006 GS 300. Check Engine and VSC Light came on after car wasn't shifting properly. The codes are P0761 and P2714. Dealer claimed transmission fluid was low said they drain and refilled the fluid. Transmission does not have a leak, so I didn't understand why they claimed the fluid was low. Car ran fine for a day then issue came back. The codes refer to shift selenoids.
View 14 RepliesCamry :: 2007 Transmission Not Shifting Into Gear Properly
I have a 2007 Camry V6 XLE with a rebuilt transmission. Since the rebuild I have had an intermittent problem with the transmission not shifting into gear properly from park. When shifting from park into drive, sometimes the transmission will pause, leaving the vehicle in neutral, then slamming into drive.
The transmission was replaced in April of 09 with a leaking transmission seal. Since this time I have has this problem but have not been able to get it to be reproduced for Toyota to observe.
Purchased: February '08 (ish)- New
First Transmission Replacement- April '09- 35980 Miles
Transmission Repair- Internal Temp Sensor/leaking o-ring/Transmission Flush- 9/13/11- 101k miles
Mazda - Mazda3 :: 2008 - Noise While Shifting Between First And Second
I hear a noise- what I can best describe as a metallic plucking sound - like a low metallic chord being plucked- when my automatic transmission 2008 Mazda3 shifts from first to second gear. It only happens the first time. I don't hear it after the car ihas been driving and is warmed up. Any thoughts on what could be happening?
View 2 RepliesMazda - Mazda3 :: Skipping Gears While Shifting
Is it ok/better/worse to skip gears while accelerating in a manual car? Example would be starting from a stop in 1st and going strait from 1st to 3rd gear. , I have a mazda 3 and i usually run 1st up to 3500 rpm or so and when i hit 3rd its around 1400 when I let the clutch out.
View 13 RepliesMazda - Mazda3 :: 2005 - Gear Selector Won't Click Into Position
The gear selector on my 2005 Mazda 3 with automatic transmission is difficult to move between P, R, N, and D positions. It does not "click" or fall into position like it used to. It has gradually gotten worse. When the car is in Park, it seems to not want to go all the way up into the Park slot. Even though the car actually parked, the P will not light up on the dashboard, which sometimes causes the car not to start when the key is turned. So sometimes I have to put it in Neutral to start.
Now the problem is that when it is in Drive, it will "fall out of gear". I put that in quotes because it is still in drive, but it was shift up to a higher gear if i don't physically pull the gear selector knob back. For example, if i'm driving and the car is in 4th gear going 60mph, and the shifter know slides up an eight of an inch, the D light will go off and the car will move into a higher gear (not sure which one, feels like 2nd or 3rd) and the engine will rev up. It doesn't feel like neutral.
Is there anything I can do myself? I plan on trading in the car in the next couple months, but I'd prefer to not have to get it worked on until then.
Saturn - Sl :: 2002 - Automatic Transmission - Shifting Delay When Put In Reverse Gear
I'm having problems with my automatic transmission in a 2002 Saturn SL. About 2 months ago I noticed a delay when I would put my saturn in reverse and it would sort of kick into gear after a few seconds (up to 10seconds sometimes). I wasn't worried much about this at first until another problem started happening. Between second and third gear it seems to be shifting slow/hard(?). I can feel where it wants to shift, but its slow to shift and actual revs high before shifting down. The problem doesn't always exist, and some days its more then others. We took it to get a transmission fluid/filter change and this didn't solve the problem. Took it back for a transmission diagnositc and GM told us we need to replace the transmission or do an overhaul. They didn't explain why really though- no clear answer. I've heard everything from the torque converter to a solenoid problem.
View 3 RepliesMazda - Mazda3 :: 2008 Engine Noise At 1400 - 1700 RPMs When In Gear
I have a 2008 Mazda3. The car has a replaced engine with 24,000 miles on it. The engine was put in before I bought the car.The car and engine run like a top; except at certain RPMs and when in gear. When I have the car in any gear (auto), the engine makes a rougher noise at RPMs 1400-1700. As I apply more gas, the RPMs seem to get stuck at 1700, then it will break through and run smooth 2000+ RPMs. The engine sounds perfect at all RPMs except 1400-1700 when in gear. When I have it in park and rev the engine, the engine sounds perfect at all RPMs.
View 8 RepliesFord Super Duty (1999-2016) :: Transmission Stays In 5th When Shifting Into Any Gear Including Reverse
I have a 2000 F-550 w/7.3 and a 6 speed ZF transmission. My problem is that when you go to shift into any gear inc. reverse the transmission stays in 5th gear. I pulled the shifter and tried to do it from top of transmission it still stays in 5th. Any thoughts that I could possibly check?
View 1 RepliesChevrolet - S-10 :: After Changing Fluid And Filter Won't Shifting All Gear Properly?
My truck was noticeably sluggish when it shifted into overdrive or would refuse to shift into it all together, so I decided to change the filter and fluid in it. After this maintenance task was done, and I test drove it, I noticed the problem was still there. It also seems now that it has trouble shifting in all gears. When I tried to "manually" shift it through all gears, the transmission would hold it in the previous gear, buck, shake and then shift at a higher RPM.
Not only this, but if I floor the pedal, the truck doesn't want to drop to a lower gear to increase RPM. It only bucks and carries on until I let out of the gas. I also noticed that when I rev the engine in park, the engine does not want to go past 4,000 RPM, and I hear a "grinding" noise at about that range. In the past, I could red-line the engine in park/idle no problem. Does the auto trans have the ability to "hold back" the engine or do I have deeper engine problems?
Grand AM :: Transmission Not Shifting Properly - Speed Odometer Not Working
Grand am is a 4cly 4speed trans. My daughter is off to school. She called and told me her speed odometer is not working. She also mentioned that it is not shifting properly if at all. Is the speed odometer operated by cable? Would the two be related to the transmission going bad?
View 4 RepliesToyota - Camry :: 1994 - Transmission Malfunction / Not Shifting Properly
I have a 94 Camry 2.2. When I am driving 45 MPH the transmissions acts like it is shifting into N or OD and then the RPMS fluctuate between idle and 1500 or so. Then when I it will shift hard because the car has decelerated. If I stay in the throttle during this it just jerks or lunges.
View 3 RepliesFord F-150 (2009-2014) :: 2013 - Transmission Not Shifting Properly?
I have a 2013 F-150 Lariat 5.0 L, 6 speed auto transmission crew cab truck with 44,000 miles on it. Recently I have experienced problems with the transmission not shifting properly. Three times when I have started out of my driveway, it has shifted into 2nd gear while I am going only 2-3 mph up my driveway which is about a 10-12 degree incline. It stays in 2nd gear even if I stop. When I pull out onto the highway, it shifted normally into the remaining gears. Then, the other night as I was returning home, while traveling up the road, it shifted into 5th gear and stayed there even when it needed to downshift. A wrench i-con appeared on my screen, my odometer showed dash lines instead of mileage and my seatbelt i-con appeared. When I got home, I shut the truck off and restarted it and everything was normal again. I have driven the truck a couple more times with no issues. The transmission shifts normally. Could a sensor be going bad ?
View 2 RepliesCelica :: 2000 - Random Power Loss - Transmission Won't Shifting Properly?
The car on cruise control sometimes randomly looses speed & downshifts to 3 and raise rpms quickly to gain the set cruise control speed again."
Vehicle Background: bought it from the original owner, the fuel gauge showed empty on a full tank of gas and I passed on the car, owner called a week later and said they installed a used PCM and everything now works, and it did, I bought it since it was a really clean car.
After driving on highway with cruise control set it would randomly loose power and downshift and then regain speed from being set on cruise control, mostly uphills and downhills but also straights sometimes and it would loose 7-8 mphs not the 1-3 mph loss that is typical of some other cars on cruise.
Engine has been rebuilt to success, other then this issue, the car drives like a dream and doesn't burn a drop of oil. Plenty of power compared to before the rebuild as well.
I learned from a DIY oil consumption fix on a 98 corolla that removing throttle body and cleaning it and the IACV, makes the vehicle idle within stock spec, really quiet and also improves the throttle response, I attempt this on the GT-S.
So I open up the airbox to make room to clean my throttle body and the 2 nuts were fairly loose, but the 2 bottom bolts were completely out that attach the throttle body to the intake manifold and only holding their place because of the tight fit in that area from all the hoses. This wasn't even touched during the engine rebuild.
I remove everything, looks dirty as [censored] and the intake has some oil in it, which I use brake parts cleaner to dry and use air to blow off and only got to remove maybe 30% of it from the inside of the intake. I then also remove the IACV to find it REALLY dirty like all the ones I had open so far and I go to town and cleaner both that and throttle body and replace both the gaskets as well.
Upon completion the vehicle's throttle response becomes AMAZING compared to before and it seem like a proper GT-S rather then a slow car which before had a slower acceleration then my 01 GT. I drive the same route home of 25 miles, the car NEVER once down shifts and has plenty of power and I'm HAPPY!
Well guess what, the issue is back now, I open the air box and both the nuts and the bolts seems firmly tight. I loosen everything up to still see the oil in the intake(though I only got to remove/dry30% the first time), brand new OEM PCV valve in the car 5k ago and I followed the PCV Valve pipe to the intake and it was dry from the inside as well.
when the vehicle is driven around and it returns to idle, it seems to hesitate(I think not 100% since it could be the engine just slowing down didn't do it before the throttle body cleaning though) for less then a second when going back to idle speed, it idles perfectly at around 750 rpms though. Questions:
1. What could be causing the oil in the intake? is it just the old oil what has been in the intake since before I bought it? The car doesn't burn any oil in the last 5k since the engine rebuild.
2. Could it be the PCM/VCM is causing the random power loss with cruise control on? which was a problem that was so called fixed using used parts but all the other automatic functions work perfectly.
3. Could it be the Cruise Control it self, apparently I can snag one from a local pick n pull for like 8 bucks (I think, listed on website)
4. Could it be this issue listed in this link? [URL] ..... , bad throttle position sensor? could it be that I cleaned the idle air control valve too roughly to get that slight hesitation when returning to idle?
5. Could it be the Throttle body itself in the GT-S? Did I clean it too aggressively, and ruined the round opening, which is causing the random loss of power? I had my cuzin do the throttle body removal and cleaning DIY step by step on our 99 corolla and he used a gasket remover (attached to a power tool) to clean up the dirt/oil build up inside the round opening and it started to give him jerks driving at highway speeds, constantly...We used the 98 corolla's gently cleaned throttle body in the 99 corolla and immediately issue solved. The proper working throttle body in the 98 corolla is a used replacement one as I aggressively cleaned the round opening in the original one and had hesitation issues as well.
Ford 6.7L Power Stroke Diesel :: 2011 - Transmission Won't Shifting Properly?
In my 2011 F-250, 6.7, auto....it seems that at certain times went the tranny shifts from 2nd to 3rd and I pause with acceleration, for some reason the tranny seems to go into a slip mode and then slams into 3rd. Now I read about 8 months ago that there was a computer upgrade via Ford. Which they did when I was having some work done on the truck at the dealership.
View 14 RepliesMazda - 626 :: 1999 - Delay When Shifting Into 2nd Gear
I have a 1999 Mazda 626. Lately, it seems to shift into 2nd gear much too late - ~5000 rpm - regardless of acceleration. Is there a good place to start diagnosing this problem? I've heard everything from new tranny to neutral safety switch.
View 6 RepliesGolf IV / Jetta IV :: 09a Transmission - No Reverse / Car Doesn't Shift From 1st To Second Properly
Bought a 2003 golf gti 1.8t as kind of a project. Car had no interior no exhaust and some shifting issues. To fix the shifting issues rather than replacing solenoids I just got a rebuilt valve body. After installation the car still doesn't shift from 1st to second properly and now I don't have reverse. (It's an 09a transmission)
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 E350 Transmission Not Shifting Properly
I recently purchased a used 2001 E350 with a 7.3L and the transmission is not shifting properly. It will go into Reverse no problem, put it in "D" and it starts in high gear and will not shift out. If I manually shift from 1 to 2 to "D" it works fine and will even go into OD. It will not down shift on its own either. What should I do to fix this issue?
View 2 RepliesChrysler - Towncountry :: Transmission Not Working Properly When Shift Into Drive From Reverse
When backing up in reverse I come to a stop and shift into drive. About 60% of the time it slams into gear (Drive). It feels as if someone rearended me. It's a 2012 Chrysler Town and Country with 40K miles. 2 dealers worked on it, reprogramed the computer and replaced 2 seloniods and the problem is still there. What is wrong but said thats typical on that 6 speed. What to do next?
View 2 RepliesMazda - B2600 :: Shifting Into Higher Or Lower Gear Getting Stiffer
Shifting into gear was a problem occasionally, but lately, within 15 minutes of driving, I start feeling the shifting into higher or lower gear getting stiffer and will not shift into gear.I've shared the problem with couple of my mechanics and it left them puzzled, since there are no leaks or low levels of fluid.
B2600i '92 cab ....