Ford Wiring/Electrical :: 1978 E350 - No Ignition Voltage - No Start?
I bought a 1952 F1 that is mounted on a 1978 E350 chassis.( 351W )
It has all the 78 wiring installed. When cranking engine, it will not start, unless you release key to run position. You have to get engine turning over, and then quickly release key to start. Checked back of switch, not losing voltage at ignition post while cranking...
Ford Wiring/Electrical :: 2012 E350 - Wiring Diagram?
Where can I find/buy a wiring schematic for a 2012 Ford E350 with the 5.4 L V8?
View 1 RepliesFord Wiring/Electrical :: 2006 E350 - Flasher For Turn Signals
I must be missing something here. Where is the flasher for the turn signals? It isn't the two relays behind the radio is it?
View 2 RepliesFord Wiring/Electrical :: Moving Engine And Ignition System - Wiring Harness For Further Use?
I plan on moving the engine/drivetrain from my 1986 F350 460 to my 1996 F250. I also want to move over the 1986's ignition system with a Duraspark 2 setup.
Although I could just cut in the easiest places to remove the wiring for later reuse I am looking for where to make the cuts, what to take and what to scrap. Alternatively I am also asking if there are aftermarket or OEM replacement sets out there are aren't a ton of money. The current harness in the 1986 has been sprayed with engine oil and cooked for 27 years so I am looking at alternative options if there are any.
Ford Wiring/Electrical :: 1997 E350 - MIL Code 4011 - Insufficient Secondary Air Injection
My 97 E350/460ci occasionally sets trouble code 4011. It clears every time I check it with my code reader. Something about insufficient secondary air injection. The dealer ship couldn't duplicate/diagnose the problem. Maybe something with the air injection solenoids.
Otherwise, it runs fine. I did notice on the passenger side of the engine compartment a large black metal filter looking thingie with about a 3/4" outlet that doesn't have any hose on it or seem to go anywhere else. Once in a while when you start it i hear a sort of soft popping noise for a few seconds that I would associate with the air pump.
Also can't get the ABS light to go away. It's out when you start it but as soon as you get going it comes on. I flushed the fluid and replaced the rear sensor to no avail. Also tried to flush out the front tone wheels and sensors.
Ford Wiring/Electrical :: 1996 E350 - Dash Losing Power During Cranking No Start
I have a 1996 E350 7.3 pstd and it hasn't started since April... Van ran great but had bad bearings in the steering column. I changed out the bearings around the steering stem and it hasn't started since but turns over just fine. The main symptom is the dash loses power when key is rotating from the last run position to the spring back crank position. Basically halfway between run and start the the dash drops power. You can see the problem very well in this video I'm attaching.
I filmed this moths ago so the dash is in disarray and I'm using a screw driver to activate the ignition switch. The screw driver bypasses the key cylinder which I thought was the problem but it's not. Parts I've replaced include new glow plug relay, new ignition switch, alternator rebuilt, 2 brand new batteries, new cps sensor, and also a new pcm. All fuses and relays have been checked and most have been tested, pcm gets power in run position as well. Gotta get this thing figured out it's been sitting for 6 months
Watch the video : [URL] ....
Ford Wiring/Electrical :: 1983 E350 - Lights And Radio Display Fluctuating When Engine Running?
I have a 1983 E350 RV with a 460 engine. It would appear that many "Mechanics" have altered the wiring in different ways. That being said I think the charging and starting electrics are fairly untouched. My issue is that once it has been running for a while the interior lights start to fluctuate so does the radio display. The AC fan speeds up and slows down and I feel like there is not enough gas being pumped up too due to some coughing and sputtering. When I press the brakes the radio stops playing and if I have the AC on it gets worse. Today I changed the voltage regulator and it made no difference. This vehicle has two batteries, one for starting the van like normal and one to run the coach part. The alternator charges both. I think it must be a bad ground somewhere but not sure where to start.
View 2 RepliesFord Wiring/Electrical :: 2003 E250 - Lost Power To Circuit 124?
'03 E250 connector C3136 located by the left lower B Pillar---have lost power to the Brown wire which seems to be designated as Circuit 124.
Which fuse controls that circuit? I have a factory EVTM but I can't find what fuse to check. And here I though I knew something?!
Ford 7.3L Power Stroke (1999-2003) :: E350 - Instrument Cluster Not Working After Electrical Wiring Mistake
I am currently converting a 1999 E350 7.3 diesel bus into a camper to live in. The bus has already had a lot of weird custom work. Done by someone else and a lot of the interior torn out and extra insulation put in. There is an exposed electrical panel behind the drivers seat. It was a cheap buy, previously fleet maintained with only 120k.
I was hooking up a battery for accessories to a terminal labeled "Battery" that does run indeed directly to the + terminal of the battery in the engine compartment.
Unfortunately I mistakenly connected the accessory battery to a terminal labeled "ignition" that runs to behind the dash. When I tried starting the vehicle off the auxiliary battery for a test everything went out for 2 seconds, I heard a click from the engine compartment, and everything than came back on. This is when I realized my mistake.
It used to be the speedo only didn't work (which I assumed was the step motor), now after this mistake all the gauges, the odometer and the buzzers don't work. Lights like the battery and airbag warning indicator still function.
Checked fuse 2 (15 amp) for the instrument cluster and it is intact. Actually checked every fuse in the vehicle in both fuse panels and all are intact. The radio works though and the vehicle is not equipped with power windows.
Going to go get a radio removal tool to take apart the dash and get back there. What this could be? Did I fry a relay? Did I fry the cluster circuit board.
Ford Wiring/Electrical :: P1451 Code - EVAP Control System Canister Vent Solenoid Circuit Malfunction
I'm not too knowledgeable about wiring and electrical systems. I'm getting a P1451 code (EVAP Control System Canister Vent Solenoid Circuit Malfunction) on my 99 4.2. I've read that it could be a bad solenoid, bad wiring, or a blown fuse. So far I've;
- checked (and changed) the related fuse
- checked the wiring for damage at the connector
- checked voltage at the connector (12 volts)
- checked the resistance at the solenoid (around 60 ohms)
- actuated the solenoid with a 9V battery (can hear it opening and closing)
I haven't had a chance to check the wiring all the way back up the frame to yet, but I noticed that the ground at the trailer wiring harness has broken off the frame. Would this potentially cause a fault in the upstream wiring? I'm going to slap a new connector on and bolt it back down anyway, but as it's Labour (Labor) Day I'll have to wait for the stores to be open tomorrow.
Ford Wiring/Electrical :: Ignition Stuck On With Key Out / Engine Kept Running
Pulled up to customers home and took key out and engine kept running. Disconnected battery, engine and aux turned off. Then Connected battery and power came on as if the key was in. Then put key in and turned with no change in power or engine trying to turn. Disc battery, put key in first then connected battery and truck started. Last stop took key out as well as disc batt and engine stayed on this time. repeated steps above several times to get back. Looking for narrowing the problem,possible ignition key cylinder, actuator or possible bad circuit.
View 4 RepliesFord Wiring/Electrical :: 1966 F100 - Ignition Totally Cut Out
Just got a 66 f100. Some one cut out the ignition. It has a toggle switch that doesn't seem to do anything, turned it to on and used a screwdriver to short the solenoid and it did not crank. I think I counted 9 cut wires in the area of the ignition counting 2 for the toggle. My other 61-66 trucks seem to just have five wires? So I can remove an ignition from one of these parts trucks, but might there be a difference since the gauges are unique to 1966 ?
Started to take the ignition out of my 62 f600 but i hate to cut wires but i must since there is no remnant of an ignition in the 66 f100. If I can match the five wires i should be ok. Just putting a battery in i have headlights, tailights and dash lights. Solenoid and cable to starter look horrible so i bought a new cable. I think i have a good solenoid or two? I didn't even get a spark when i shorted the solenoid with a screwdriver....
Ford Wiring/Electrical :: Ignition System Keeps Shorting Out / Killing Spark
I have a 77 ford truck with a 351 ,the ignition system keeps shorting out, killing spark. If i replace the starter solenoid, it works for a while, then goes out again. I have replaced 4 solenoids this month. What could be shorting the solenoid out? Had the truck for 8 yrs. now, never had a problem with it till now. It has a mallory dist. it was in when i bought it.
View 7 RepliesFord Wiring/Electrical :: 1977 - No Start - Ignition Wire Melted?
My 77 F150 Ranger with a 400 in it didn't wanna start up at all. It wouldn't even crank or click like if the battery was dead. Then I tried again this morning and it cranked once then melted a red wired with I think a black or gray tracer, on the ignition. (I put a new solenoid on a couple months back and the positive also melted a bit by the solenoid but didn't pay any attention to it.) I'm just wondering what could be wrong with it to make it do that and how to fix it. Also when I went to put gas in it (it's on a slight hill making it lean to the driver side) it was empty but no fuel would go down the filler neck, then it started to gurgle and spit it out some. I was told it was vapor lock but I thought vapor lock happens when it's hot.
View 3 RepliesFord Wiring/Electrical :: Door Locks Attempting To Activate When Turning The Ignition Key?
Having problems with their door locks attempting to activate when turning the ignition key? If so, how can I correct it or make repairs.
View 4 RepliesFord Wiring/Electrical :: 1986 - Lost All Power To Fuse Box After Hitting A Bump / No Ignition
here its is i have a 1986 ford f350 6.9 aftermarket turbo set up i was driving it then i went over rail road tracks lost all power to fuse box no headlights no interior lights no ignition power batteries are good so now when i turn key nothing lights up it just killed my whole truck....
View 7 RepliesIgnition - Electrical-wiring - Engines - Civic - Honda :: 2002 - CEL Came On?
So my Honda Civic has been flashing my check engine light, which is telling my my cylinders are misfiring. I checked the ignition coils by removing them while the car was running and cylinder 2 and 3 I can remove and it doesn't change how the car runs. I put a new ignition coil In and that doesn't work so it isn't the ignition coils, what it could be?
View 8 RepliesIgnition - Starting - Electrical-wiring - Starters :: 2006 - Delayed Start Intermittently?
Our Honda Odyssey will have an occasional delayed start where you turn the key but no sound occurs. All the lights come on like normal and the automatic doors can all close and open without any issues. Originally we didn't know that we could eventually get the car to start by turning and holding the key in the start position. It happens every couple days to couple weeks and without holding the key in the on position it will be anywhere from 30 minutes to 3 days before the car will start normally again. We've spent about $1,000 at the Honda dealer to have the battery, battery cables, starter, and starter relay replaced but we're still having the problem.
View 2 RepliesFord Wiring/Electrical :: 2007 - Reverse Lights Won't Work?
so I recently purchased a 2007 f350 SCSB and my reverse lights don't work. I am trying to trouble shoot the cause... So far I've replaced the bulbs and tested the plugs and im not receiving any power to them... Where to start to look for the problem?
View 3 Replies