Ford Wiring/Electrical :: Ignition System Keeps Shorting Out / Killing Spark
I have a 77 ford truck with a 351 ,the ignition system keeps shorting out, killing spark. If i replace the starter solenoid, it works for a while, then goes out again. I have replaced 4 solenoids this month. What could be shorting the solenoid out? Had the truck for 8 yrs. now, never had a problem with it till now. It has a mallory dist. it was in when i bought it.
View 7 RepliesFord Wiring/Electrical :: 1987 F250 - Engine Compartment Harness Smoked
1987 F-250 4x4, 460cid... My engine compartment harness smoked. Do the 1987 models have wiring problems and I need any wiring diagrams that are out there.
View 6 RepliesFord Wiring/Electrical :: Ignition Stuck On With Key Out / Engine Kept Running
Pulled up to customers home and took key out and engine kept running. Disconnected battery, engine and aux turned off. Then Connected battery and power came on as if the key was in. Then put key in and turned with no change in power or engine trying to turn. Disc battery, put key in first then connected battery and truck started. Last stop took key out as well as disc batt and engine stayed on this time. repeated steps above several times to get back. Looking for narrowing the problem,possible ignition key cylinder, actuator or possible bad circuit.
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Ignition Harness Wiring Colors?
My 2000 f350 has wires that dont match anything I've seen. I need to mate this to an 08 harness so I need to be accurate. I have
(2) yellow. I know this is 12v constant
(2) green/purple I know this is 12v constant
(1) red/black
(2) solid red
(1) solid black
(1) gray/light blue
Ford 6.7L Power Stroke Diesel :: 2016 F550 - Ignition Wiring Harness Diagram?
I need to connect a remote start stop for a bucket truck attachment to this new 2016 F550. Found everything except the ignition wiring harness diagram. Need to know what I can tie in to.
View 4 RepliesFord Audio/Video System :: 1999 - Powerstroke Amp Installation - Wiring Harness?
I am no novice at stereo system upgrades but have never done anything to a diesel before so here it goes....99f-250 powerstroke....which battery should i hook the amp power cable to driver side or passenger side or does it matter?
View 3 RepliesFord Ranger / B-Series :: 2007 - Replacing Pioneer Audio System - Dash Wiring Harness?
I'm going to replace the bone stock/non-"Pioneer Audio System" radio with a new Pioneer head unit in my 2007 Ranger Super Cab. After looking at the wiring between the third-party Metra Ford adapter and the supplied Pioneer harness, I'm left with a couple of connections that must be made to other wiring harnesses in the dash.
First up is a wire from the supply side of the parking brake switch; the second is to the supply side of the Reverse lights. These are in the Pioneer harness and both are about 12" long, so I'm guessing the connections can be accessed fairly close to the radio well in the dash.
Installing a new Pioneer radio in their 2007, and where did you pick off those two connections?
Ford Wiring/Electrical :: 1967 F100 - Instrument Cluster Gauge Wiring
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
Ford Wiring/Electrical :: 2002 - Complete Headlight Switch Wiring Diagram?
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 RepliesFord Wiring/Electrical :: 1997 F250 - Rear Tail Lights Wiring
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 RepliesFord Wiring/Electrical :: 2004 - Instrument Cluster Wiring Diagram?
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 RepliesFord Wiring/Electrical :: 7 Pin Trailer Wiring - Running Lights Not Working
Just bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 RepliesFord Wiring/Electrical :: 2004 - Installing Seat - Wiring And Functions?
Im installing a set of 04 lariat seats into a 00 truck. I need to know how to hook up the heat. The power part is no problem. What I thought was right which was a separate constant 12v and a switched 12v for the module and ground apparently isnt right. If somebody could ohm out their harness on a 01 truck that would be great. As I have it right now the light on the switch comes on but almost instantly turns off.
View 14 RepliesFord Wiring/Electrical :: 1987 F150 - Wiring Diagram With Carburetor?
Looking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 RepliesFord Wiring/Electrical :: Wiring 2008 Seats In 2001 Model?
Let me start by saying electrical is something I really have no knowledge of....(never used any kind of an elec meter and don't have one) simple, Pos-grd and fuse, NP. I really don't want to fry something in these expensive new seats w/my normal trial and mostly ERROR!
The 08 (drivers) seat has 4 wires in the input clip.
GRN-RED (heavy gauge)
BLK-PURP (heavy gauge
BLU-RED
BLK-WHT
and my 01 whip out of the floor has a 3 wire setup.
GRN (heavy gauge)
BLK (heavy gauge)
BRN-BLU
I can wire PS side seat from fuse box and ground it NP. It only has a 2 wire set-up in the new seat.
Ford Wiring/Electrical :: 2007 E350 - Tap Into Ignition Circuit?
I have a 2007 e350. I installed a battery isolator and I believe I need to run a wire from the ignition circuit to the exciter post on the isolator. I found the Power Distribution Panel under the hood (drivers side) which has a fuse in slot #7 (60 amp Maxi Fuse) listed as Ignition Switch/Accessory Delay. What is the best way to tap into this?
Also, I have 8 gauge wire which I ran from the isolator to the batteries. I am second guessing this now and wondering if I should go with thicker wire?
Ford Wiring/Electrical :: 1966 F100 - Ignition Totally Cut Out
Just got a 66 f100. Some one cut out the ignition. It has a toggle switch that doesn't seem to do anything, turned it to on and used a screwdriver to short the solenoid and it did not crank. I think I counted 9 cut wires in the area of the ignition counting 2 for the toggle. My other 61-66 trucks seem to just have five wires? So I can remove an ignition from one of these parts trucks, but might there be a difference since the gauges are unique to 1966 ?
Started to take the ignition out of my 62 f600 but i hate to cut wires but i must since there is no remnant of an ignition in the 66 f100. If I can match the five wires i should be ok. Just putting a battery in i have headlights, tailights and dash lights. Solenoid and cable to starter look horrible so i bought a new cable. I think i have a good solenoid or two? I didn't even get a spark when i shorted the solenoid with a screwdriver....
Ford Wiring/Electrical :: 2000 - Electric Shift Transfer Case Wiring Diagram?
I am curious if it is possible to make a stand alone controller for the electric shift transfer case in a 2000 F-350?
The reason I ask is, this is swapped into a 4x4 conversion in a van and I would like the transfer case to work like the factory, but I don't want to swap over the whole GEM module. I have the high to low and low to high shift relays and wiring, the selector switch from the dash.
I know that powering up the relays will shift the transfer case, but the GEM module tells when the relays need to shut off, and that is where I am not sure what to do. I am assuming that the other plug on the shift motor (6 pin plug) is the sensor that tells the GEM module where the shift is at.
What needs to be done (with a bank of relays).....
Ford Wiring/Electrical :: Different Color Wires In Cab - Brake Light Not Working - Wiring Diagram?
Need a wire diagram. I have a connector in the cab that has red,blue,lt green,white wires. It's causing my brake lights not to work. I need a wire diagram that shows were they go. I can't find these wires in my Haynes manual.
View 3 Replies