Ford Transmission :: 1989 F350 - Harder To Shift / Grinding Noise Like It Doesn't Want To Go In Gear
I have a 1989 F-350 7.3 IDI with a ZF-5 trans. Lately, I noticed that it was a little harder to shift my truck through gears while driving than it normally is, and when I'm stopped and try shifting into first gear or something it like vibrates and makes like a grinding noise like it doesn't want to go in gear. For a while, I've also had to push on the clutch very hard in order for it to I guess hit the linkage and start, but I never had problems shifting until lately.
Today though, I went to start my truck, I pushed on the clutch as hard as I could, and the switch would not engage so I couldn't start it. So, I guess the switch was farther to link than the pedal could possibly go. I went under the dashboard and engaged it by hand then it started. I drove home and the shifting was still iffy. How can I make the switch engage normally again so its closer I guess and so I don't have to push so damn hard on the clutch to get it to start? And could the switch linkage have anything to do with the shifting being funky lately, or could that only be the clutch itself?
Golf IV / Jetta IV :: Transmission Grinding When Shift Fast From 2nd To 3rd Gear
Have a question when I shift slow from 2nd to 3rd my o2j tranny doesn't grind but when I shift fast from 2nd to 3rd it grinds it happens starting at 3000 Rpms thru 6000 Rpms. It also doesn't happen when I shift from 4th to 3rd. Have performed a tranny fluid change. Along with replacing the clutch at 1500 miles ago. The engine is AWP.
View 4 RepliesSonata NF (2006-10) :: 2008 - Grinding Noise When Shift From First To Second Gear
I am now getting a grinding noise when I shift from first to second gear. It sounds like the two metals rubbing each other. Its not happening all the time, but for the past two days a bit frequently
I had reported this grinding noise when I turn left a month back. Was thinking because of my worn out tyres, but apparently not.
Ford 7.3L Power Stroke (1999-2003) :: Loud Gear Meshing Like Grinding Noise - Delayed Hard Shift 2 - 3
I have an early 99 F250 4x4 7.3L..... 4R100....
Brief history, a while back on way home from work I let off of the accelerator and had a loud gear meshing like grinding noise, got back on the accelerator and went away, let off and back, so I quickly stopped and pulled over, went through the gears and reverse, everything seemed ok,??? went on my way, got home parked the truck and went about my evening. came out next day to leave and truck wouldn't move in reverse, forward but not reverse. long story short I was told that the snap ring internally probably came out, I have heard of this being a big issue with these, so I set up for it to be rebuilt, got it back and installed and still same issue, what the crap so I ended up having to pull it back out and amongst my own trouble shooting I found the simple issue and was the nylon riders on the 4hi/4low shifter fork were completely gone and allowing the planetary group to free float in and out of 4x4 neutral!!! NOW on to the issue at hand. so far only thing has been done is rebuilt and those fork riders replaced.
now I can move but 2-3 upshift under a load(more noticeable) has a delay going from 2nd to 3rd and under a load it hits hard. I talked to the guy that rebuilt it and he said that the rebuild kits don't always the right springs for the valve body and causes shift issues, so he talked me into the shift corrector kit which I researched and did see what he was saying, so had that done and still no better, still does it, however, it does shift into the gear softer but didn't fix the delay or the hitting hard when it did finally go into 3rd.
After being forced to drive it that way I have since determined that what it happening is it is coming out of 2nd with a second and half pause and then shifting into 3rd, the hard shift comes in to play because during the delay the torque convertor is locking up making it a direct drive like popping the clutch on a standard!!!
I just swapped out the sol pack and I heard from a youtube video that the bolt next to the 2-3 upshift valve on the valve body could be to tight and making a sticky valve, so I re-torqued all the bolts and nuts put all back together and test drive proved to be worse, I now have same issue in all upshifts. all hit hard now, I am at a loss and don't know where to go from here, I can only imaging the sol pack is causing this but I have yet put my org one back in to see... oh and I found two bolts on the accumulator stripped and found one non torqued bolt on the main valve body!!
Saab - 9-3 :: Grinding Noise From Manual Transmission In 3rd Gear
I have a 98 saab 900 se turbo.90000 miles on it. Just had a new clutch kit/throwout bearing and master cylinder clutch installed, as the clutch was going bad.
When I shift the car (while driving) from 2nd into 3rd/4th/5th gear,and accelerate I suddenly notice what sounds like a "grinding"/raspy noise that stays with the car while in those gears. It does not occur in 1st or 2nd , although it seems that in first gear the rpms go up real fast now (could the gears be slipping again?? this is a brand new clutch..).
The second I shift to 3rd gear and give it gas, the noise shows up instantly. Now when I let my foot off the gas, the noise goes away 100%. The second I give it gas again, it comes back. Also I don't believe the noise increases or decreases in relation to the speed of the vehicle. It seems to stay constant no matter what speed I'm at, as long as I'm actively giving it gas.
It occurs every time I drive..not sure what to do and what causes this..maybe I just need to check the transmission fluid?
Golf VI R :: Clicking Noise From Transmission When Shift Gear
I have the mods listed below in my signature. When I shift gear and have almost completely released the clutch to move up into the next gear I get a clicking noise and feel from my transmission I think or maybe differential. This is with traction control off and is only noticeable at lower rpms like a low rpm shift from 1st into second.
View 7 RepliesFord Super Duty (1999-2016) :: 2010 F350 - Transmission Makes A Weird Noise When Takeoff And Shift Into Gear
I bought this truck with 60,000 miles and have had about 3 months. I don't drive it very much but when I do I have noticed that when it sets for 4-5 days or longer the transmission makes a weird noise as you take off and does does shift into gear as it does when I use it ever day. The problem goes away very quickly (not even a 1/4 mile driving) and everything is fine after that. By the way I took it to the ford dealer who did a complete 60,000 mile service on it that was suppose to include changing the transmission fluid and filters-could they have screwed something up (I did not notice this issue until after the 60,000 mile service?).
View 7 RepliesFord Transmission :: 1986 - Replaced Torque Converter Now AOD Transmission Won't Shift Out Of 1st Gear?
Replaced Troque Converter, Truck runs engine runs fine transmission won't shift out of 1st gear.
View 2 RepliesFord Transmission :: FMX Transmission Will Not Shift In To 3rd Gear
I have a Ranger that I have put a 302 engine with an FMX transmission in...everything seems to be working correct except the transmission will not shift in to 3rd gear... don't know alot about transmission.. could this be a linkage adjustment issue?
View 6 RepliesGolf/GTI VI :: 2010 - Bad Grinding When Shift From 1st To 2nd Gear
when i shift from 1st gear to 2nd gear, above 2500 rpms i get a really bad grinding, i am just under 50,000 miles so it is going to the dealership to get fix. It also kicks me out of second gear some time.
View 24 Replies3000GT/Stealth :: Grinding When Shift Into Reverse And Car Won't Go Into Gear
Buying a vr4 this weekend with dr650 turbos... The only problem with car is when you shift into reverse it grinds and won't go into gear, I'm thinking its the reverse synchro?
View 2 RepliesAccent LC (2000-05) :: 2003 - Grinding When Shift From 1st To 2nd Gear
Why my car is grinding gear when I shift from 1st to 2nd, & yes the clutch is fully depleted and still grinds when I shift.
View 4 RepliesFord :: Automatic Transmission Sometimes Not Shift Into First Gear
I have a 36 foot motor home on a 2000 Ford F53 chassis. (similar to single axle freight trucks and school busses) After getting one set of the rear wheels partially stuck, which resulted in some spinning of that side, the overdrive off light on the shift lever began to blink and the service engine soon light came on. The fault code said, "speed sensor showing more than one mile per hour". Now the automatic transmission sometimes will not shift into first gear after stopping and has to be manually downshifted, after which, it works fine.
View 1 RepliesFord Transmission :: 4R70W - No First To Second Gear Shift
Working on a 2004 E-250 van. [URL] ....
I went through this transmission completely, its back in the van and I get no 1-2 shift.
when I first put it together, I missed the hole in the flex plate for the torque converter stud and started tightening the bell housing bolts down, I heard loud "POP" and realized what I had done. maybe I damaged the pump?
forward and reverse engagement is firm, both give a nice bump when it goes in gear. This tells me the forward clutch is working, but the intermediate clutch is not applying to make second gear happen.
I have done all the easy stuff I can think of, replaced the shift solenoid and put in a new 1-2 accumulator piston. I guess i need to air check the intermediate clutch piston again and make sure its applying. this a 2004 model trans, so it has the new style pump and intermediate piston.
Ford Transmission :: Grinding Noise Coming From The Transmission
I swapped a t5 transmission from a s-10 into my 52 ford f3. I am trying to rundown a grinding noise coming from the transmission. I replaced the throw out bearing and the input shaft bearing on the transmission. With the transmission partially apart I couldn't find any obvious problems. The noise is only present when the clutch is depressed either in gear out out of gear.
Left in neutral there isn't any noise. I initially thought the throw out bearing was the culprit and replaced both that and the input shaft bearing. What could be wearing out? The transmission shifts perfectly but there is a binding noise when the clutch is released in first and sometimes second gear. another binding noise is present when making a hard left turn while starting out. I am at a loss here....
Ford Transmission :: 4r70w - Truck Tries To Shift Into 4th Gear
I have a 2005 ford expedition with 91000 miles, it has the 5.4 w/ the 4r70w transmission.
For some reason when my truck tries to shift into 4th gear, the RPM's climb to approx. 3000 rpms (meanwhile the truck is not gaining speed) and slowly drops down to about 1000-1500. once the rpms drop down fourth gear eventually engages and I can go about my business as normal as long as I do not let my mph drop too low.
If I turn O/D off, the truck drives perfect, minus not having overdrive.
If I come to a dead stop and put the truck in 2nd gear, with O/D on the truck drives great and it has good engine braking so I am assuming that the band is holding.
I took it to a transmission shop to have some diagnostic checks done, they told me that fourth gear was barely engaging and that they would have to tear apart the transmission to diagnose it further, I told them not to disassemble the transmission.
So I changed out the torque converter (which I assumed was "fourth gear") and changed out all the fluid, the fluid looked a little burnt but there was no debris in the pan but there was some silver material on the tranny pan magnet, and installed a new filter. and the problem still exists.
Ford Excursion :: 2000 - Transmission Won't Shift From 1st Gear?
I have a 2000 Excursion w/ V10 and I have an issue with the transmission form time to time. some times it does not want to shift out of first. if I pull over and turn it off for a few minutes it will be fine for a while and it doesn't do this all the time. A few nights ago it did this so I pulled over and turned it off and it still did it but then it started shifting on its own just fine till we got on the high way which is started shifting in and out of over drive going around 60-65 MPH. didn't want to go too fast not knowing what it could or would do. it did this for a few miles then it started working fine. next day it did the same thing not wanting to shift out of first then started working fine. drove it around last night and it all worked perfectly. The CEL is on but I get a no communication text from the scanner so that is another thing I need to look in to. I'm guessing it is an electrical issue being when it works it shifts fine and it does not slip at all.
View 14 RepliesFord Transmission :: 1985 F250 Won't Shift From 1st Gear?
Well I Took my truck (1985 F250 6.9L IDI C6) and went through a little mud bog got some water in the tranny, no biggy i flushed the fluids out a couple times and went to drive it. But now it wont shift from 1st to 2nd but i can manually shift it from 1-2 I replaced the Modulator and that havent made a difference. Is there anything I should look into?
View 14 RepliesFord Transmission :: 1996 F250 Will Only Shift To 3rd Gear
On my 96' F-250 4x4, The tranny will shift to 3rd gear and that's it. If I put it in Neutral and then back into drive it will stay in 4th gear for about 15 seconds then go back to 3rd. What could be causing that?
View 14 Replies