Ford Transmission :: 1986 - Replaced Torque Converter Now AOD Transmission Won't Shift Out Of 1st Gear?
Replaced Troque Converter, Truck runs engine runs fine transmission won't shift out of 1st gear.
View 2 RepliesFord :: Automatic Transmission Sometimes Not Shift Into First Gear
I have a 36 foot motor home on a 2000 Ford F53 chassis. (similar to single axle freight trucks and school busses) After getting one set of the rear wheels partially stuck, which resulted in some spinning of that side, the overdrive off light on the shift lever began to blink and the service engine soon light came on. The fault code said, "speed sensor showing more than one mile per hour". Now the automatic transmission sometimes will not shift into first gear after stopping and has to be manually downshifted, after which, it works fine.
View 1 RepliesFord Transmission :: 4R70W - No First To Second Gear Shift
Working on a 2004 E-250 van. [URL] ....
I went through this transmission completely, its back in the van and I get no 1-2 shift.
when I first put it together, I missed the hole in the flex plate for the torque converter stud and started tightening the bell housing bolts down, I heard loud "POP" and realized what I had done. maybe I damaged the pump?
forward and reverse engagement is firm, both give a nice bump when it goes in gear. This tells me the forward clutch is working, but the intermediate clutch is not applying to make second gear happen.
I have done all the easy stuff I can think of, replaced the shift solenoid and put in a new 1-2 accumulator piston. I guess i need to air check the intermediate clutch piston again and make sure its applying. this a 2004 model trans, so it has the new style pump and intermediate piston.
Ford Transmission :: 4r70w - Truck Tries To Shift Into 4th Gear
I have a 2005 ford expedition with 91000 miles, it has the 5.4 w/ the 4r70w transmission.
For some reason when my truck tries to shift into 4th gear, the RPM's climb to approx. 3000 rpms (meanwhile the truck is not gaining speed) and slowly drops down to about 1000-1500. once the rpms drop down fourth gear eventually engages and I can go about my business as normal as long as I do not let my mph drop too low.
If I turn O/D off, the truck drives perfect, minus not having overdrive.
If I come to a dead stop and put the truck in 2nd gear, with O/D on the truck drives great and it has good engine braking so I am assuming that the band is holding.
I took it to a transmission shop to have some diagnostic checks done, they told me that fourth gear was barely engaging and that they would have to tear apart the transmission to diagnose it further, I told them not to disassemble the transmission.
So I changed out the torque converter (which I assumed was "fourth gear") and changed out all the fluid, the fluid looked a little burnt but there was no debris in the pan but there was some silver material on the tranny pan magnet, and installed a new filter. and the problem still exists.
Ford Excursion :: 2000 - Transmission Won't Shift From 1st Gear?
I have a 2000 Excursion w/ V10 and I have an issue with the transmission form time to time. some times it does not want to shift out of first. if I pull over and turn it off for a few minutes it will be fine for a while and it doesn't do this all the time. A few nights ago it did this so I pulled over and turned it off and it still did it but then it started shifting on its own just fine till we got on the high way which is started shifting in and out of over drive going around 60-65 MPH. didn't want to go too fast not knowing what it could or would do. it did this for a few miles then it started working fine. next day it did the same thing not wanting to shift out of first then started working fine. drove it around last night and it all worked perfectly. The CEL is on but I get a no communication text from the scanner so that is another thing I need to look in to. I'm guessing it is an electrical issue being when it works it shifts fine and it does not slip at all.
View 14 RepliesFord Transmission :: 1985 F250 Won't Shift From 1st Gear?
Well I Took my truck (1985 F250 6.9L IDI C6) and went through a little mud bog got some water in the tranny, no biggy i flushed the fluids out a couple times and went to drive it. But now it wont shift from 1st to 2nd but i can manually shift it from 1-2 I replaced the Modulator and that havent made a difference. Is there anything I should look into?
View 14 RepliesFord Transmission :: 1996 F250 Will Only Shift To 3rd Gear
On my 96' F-250 4x4, The tranny will shift to 3rd gear and that's it. If I put it in Neutral and then back into drive it will stay in 4th gear for about 15 seconds then go back to 3rd. What could be causing that?
View 14 RepliesFord Transmission :: E350 - Auto Gear Shift?
How the auto gear shift works on a ford E350.Does it work by wires or does it have a steel column to change the gears.I have looked for pictures but with no luck. I have spent 2 hours looking.
View 4 RepliesFord Transmission :: Grinding Noise Then Shift Into Gear?
I have a f1ta 5 speed trans on my 4.9 and when i press the clutch in and shift into 1st gear it makes a grinding noise then goes into gear after a little patience. but if i press the clutch and wait a few seconds, then shift into 1st its fine and goes right in.... maybe syncronizers not meshing or they're worn? or could it possibly be a low fluid prob? idk, it just started happening.
View 3 RepliesFord Transmission :: 1982 F150 - Slow To Shift Into Any Gear
My 82 f150 4x4 302 c6 trans is acting up. My c6 is slow to shift into any gear when I shift the column shifter, after a moment it jerks into gear, also it doesn't seem D is doing anything but all the other gears seems to function manually or auto.
Fluid level looks ok, maybe a little high on the dipstick. I'm going to check the modulator and do a fluid/filter change but looking for a link to the band adjustment screw ?
Ford Aerostar :: 1998 - Transmission Won't Shift / Stay In 1st Gear
It's a 1988 with a 3.0 engine and an automatic transmission. It doesn't want to shift. I can make it shift manually, but if I leave it in OD, it wants to stay in 1st gear . If you fiddle with the accelerator, you can get it to shift. Then it wants to stay in 2nd, and so on.
Like I said, if I use the gear selector to manually shift, it will go to all four gears just fine.
My thoughts are a vacuum leak (a big one) or a faulty vacuum modulator at the transmission. No, the vacuum line to it doesn't have tranny fluid in it, but I replaced it, and I wonder if it's bad. Yes, I made sure to put the little metal pin/link back in it.
Ford Excursion :: Tightening Transmission Gear Shift Selector?
Fix a Loose Column Shifter on Ford Vehicles - YouTube
The first pic shows the torx screws that come loose, allowing the handle to get sloppy.
The second pic shows the black plastic adjuster wheel that centers the gear shift selector needle on the proper designated gear displayed in the indicator window.
Ford Ranger / B-Series :: 2000 / 4R44e Transmission - Hard Shift From 2 - 3 Gear
2000 Ranger 4R44e transmission.Hard shift from 2-3 gear and when i run about 35-40 mph and brake then acelerate it downshifts hard . Whats wrong with it?
View 14 RepliesFord Super Duty (1999-2016) :: Transmission Will Not Shift Out Of Gear Occasionally
2015 F 250, less then 5k miles. When towing travel trailer, weight 7500lbs, on occasion transmission will not shift out of gear. Happens in first, second, or third. Very intermittent. Take off from a stop engine goes to 6k rpm. Let foot of the throttle goes all the way back to idle, still no shift. Accelerate back up to speed still will not shift. After doing this a couple of times finally shifts. Have had this happen in second and third. Not a lot of fun with cars behind you or trying to merge on highway. No codes
First trip to Ford dealer they re calibrated computer. Still happened towing. Second trip to dealer they put a flight recorder on it and I towed again. Did not hang up in first or second ,but would not shift out of third on highway doing 70mph, even when I lifted from the throttle and coasted. I finally shifted to manual and shifted to fourth and was able to upshift After reading flight recorder mechanic said it appeared normal. I explained that having to shift the transmission manually is not really normal and they agreed.
Ford 6.7L Power Stroke Diesel :: Automatic Transmission Hard Shift Second Gear
Well I've been towing for almost 150,000 miles with a 2012 6.7 Lariat 4 wheel drive. Things have been going pretty well with the truck. I noticed some sluggish and indecisive type shifts early on but now I'm worried. I depend on this truck for pulling a horse trailer all over the country and Canada. Just recently I've been getting a hard shift or a thump or a clunk when shifting up or down in to second gear. I'm at about 152,000 miles and did a hot flush with LV ATF at about 148,000 miles. Should I worry or keep running?
I have a 97' PSD I'm thinking of giving a nice paint job and a flat bed but am reluctant to do so due to financial concerns and the fact that some folks may not want to see me pull up in an old truck no matter how nice it looks. My tranny temps have been stating under 200F and I really keep an eye on the temps when running up and down the hills while towing. The trailer is a 35' Gooseneck with a max GVRW or 14,000 pounds. Should I wait for the tranny to grenade and then drop in a built tranny and if so who's building these tranny's stronger than stock? Long time no see but this site has always been my go to for all my Ford truck questions, upgrades, etc.
S-10 :: Transmission Hard Shift Into 2nd Gear?
I get a hard shift into second gear, it jerks into 2nd but not all the time. I only notice it after driving on the freeway for several miles. It has 60,000 original miles. Service Engine Soon light come on after the hard shifts with a transmission fault code. I reset the Engine light and let it set 20 or so minutes and it shifts like new.
1997 CHEVROLET TRUCK S10 2WD
6 Cylinders 262 X 4.3L SFI
Automatic
Ford Transmission :: 1989 F350 - Harder To Shift / Grinding Noise Like It Doesn't Want To Go In Gear
I have a 1989 F-350 7.3 IDI with a ZF-5 trans. Lately, I noticed that it was a little harder to shift my truck through gears while driving than it normally is, and when I'm stopped and try shifting into first gear or something it like vibrates and makes like a grinding noise like it doesn't want to go in gear. For a while, I've also had to push on the clutch very hard in order for it to I guess hit the linkage and start, but I never had problems shifting until lately.
Today though, I went to start my truck, I pushed on the clutch as hard as I could, and the switch would not engage so I couldn't start it. So, I guess the switch was farther to link than the pedal could possibly go. I went under the dashboard and engaged it by hand then it started. I drove home and the shifting was still iffy. How can I make the switch engage normally again so its closer I guess and so I don't have to push so damn hard on the clutch to get it to start? And could the switch linkage have anything to do with the shifting being funky lately, or could that only be the clutch itself?
Camry :: 2002 Transmission Does Not Shift From First To Second Gear
My 2002 Camry has an automatic transmission that works fine except when it is about 20 degrees or colder. The problem is that the transmission does not want to shift from first to second gear. After about ten minutes things shift normally. Other than that I have had no issues with the transmission.
View 3 RepliesSC/SL/SW :: 5 Speed Manual Transmission - 97 SL2 Won't Shift Into First Or Second Gear
My 1997 Saturn SL2 with 5 speed manual transmission won't shift into first or second gear. When I shift into the location where first would be the car is in third gear. It shifts into 4th, 5th and reverse just fine, though the shifter is in the wrong position for those gears. I can wiggle the shifter in neutral and get it to move into the position where 5th and reverse are normally found, but it is stiff and makes a clunking noise when I move the shifter over to the far right side.
I have removed the center console and the bushing appears to be intact. Both cables are in their proper positions inside the vehicle and at the engine. One of the cables (the top one in the engine) has some wear and tear on the boot, but does not appear to be binding. Other than the stiffness and the clunking noise, the shifter seems to be working fine too.