Accent LC (2000-05) :: 2003 - Lost The Ability To Shift Out Of 2nd Gear
My 2003 made a sharp mechanical noise one day, next thing I knew it lost the ability to shift out of 2nd gear....Now, it can still shift into 2nd gear when cold, but only after holding rpm for a bit and then suddenly jerking into 2nd gear. Once it's warmed up for a few minutes though, after dropping out of 2nd gear, that's it! Then it's stuck in 1st gear the rest of the time. Reverse doesn't work anymore at any time, and it gave me code P0732 to P0734 which should be gears 2 - 4. Is it possible that not being to get out of 1st means 2nd gear is broken, but the other 2 are okay and it just can't get shift past 2nd? Or might all 3 have problems after all?
View 1 RepliesAccent LC (2000-05) :: Car Shift Violently Between 2nd And 3rd Gear
I have a 2001 Hyundai Accent GS Hatchback, the car has about 41,6xx miles on it. When i drive it between 2nd and 3rd gear it shift violently, its almost like it shifts due to pressure, it also happens when it downshift too. Also the reverse went out, i can hear the pump running and it goes into reverse but when i press on the gas it acts like it in neutral. This is a daily driver for me.
View 9 RepliesAccent LC (2000-05) :: 2002 - Gear Grinding And Leaking Slave Cylinder
When changing gears my accent grinds as if its not engaging properly? I checked my slave cylinder and the rubber was filled with silver looking fluid could me replacing the S/C fix the issue? I don't think its synchro issue i tried double clutching and still no difference. the grind sounds the exact same as it does when you accidentally release your clutch when changing gears and it hasn't engaged properly. I also changed my manual gear box oil.
View 2 RepliesAccent LC (2000-05) :: Won't Shift Past Third Gear Until Car Is Warm
I have a 2000 Accent that wont shift past third gear until the car is warm. The car has 140k miles. When I turn on the car and pull onto the high way it sticks in 3rd. I then have to slow down and drive through a small town. When I get on the other side of the small town and get back up to speed it will shift. Over drive is on.
View 4 RepliesAccent LC (2000-05) :: Manual Trans Notches Sometimes When Shift Into 2nd And 3rd Gear
I just got a 2000 accent. The problems is that sometimes when I shift into 2nd and 3rd is notches sometimes. But it does not do it when i shift down. Also if I shift fast it will occur less often as when I shift low. When my friend drove the car it didnt do it for him. So maybe it is how i drive or something. I make sure the clutch is down all the way.
View 7 RepliesAccent LC (2000-05) :: When Shift Into 2nd Gear Car Seems To Stop Powering Wheels Temporarily
I have a 2002 Accent 1.6 with 187000 km on it. I started noticing over the last month that when I shift into second gear the car seems to stop powering the wheels temporarily. Once the RPM's pick up (around 2200) the problem goes away. This seems to only happen when I originally shift into second and the RPM's are lower. If I accelerate slowly then the lag usually won't happen, but if I push down more on the gas then you can really notice the lag.
The spark plugs only have 15000 km on them, air filter is new, just replaced the fuel filter, oil was just changed (synthetic) as well as the filter, and I just recently cleaned out the throttle body. I have also seemed to notice a loss of overall power since at highway speeds since this problem started. The engine doesn't lag when I'm in 4th or 5th gear on the highway, but it seems to have less power when I'm accelerating on the highway.
Accent LC (2000-05) :: 2001 1.6 Cranks But Won't Start / Car Wouldn't Shift Into High Gear
I have just recently acquired an 01 Accent with the 1.6L and have had a few problems with it. It has about 112,000 miles on it and at about 109,000 it had the following services performed by the previous owner (reputable shop did the work)
-New battery
-New timing belt kit
-New water pump
-New valve cover gasket
-New plugs
-New belts
-New front pads
-New front rotors
-New rear wheel cylinders
-New front CV axles
-New tires all around
-Alignment
Now since I got it with about 111,000 miles on it, it ran and drove great until I had to put a new alternator on it as well as having to take the center console and automatic shift lever out to repair the wires for the O/D button. Car wouldn't shift into high gear. The problem I am having now is the car will crank but it will not start. Not even a sputter. I drove the car to and from work the day previous and then went out and started it to go to work in the morning and it started fine and ran fine for a minute or two then it just died like I turned the key off. No spitting or sputtering like it was running out of gas just died completely. Checked a few fuses and such and really not sure where to go from here because I don't have a code reader and don't wanna just throw parts at it, I would rather troubleshoot the problem.
Ford 7.3L Power Stroke (1999-2003) :: Loud Gear Meshing Like Grinding Noise - Delayed Hard Shift 2 - 3
I have an early 99 F250 4x4 7.3L..... 4R100....
Brief history, a while back on way home from work I let off of the accelerator and had a loud gear meshing like grinding noise, got back on the accelerator and went away, let off and back, so I quickly stopped and pulled over, went through the gears and reverse, everything seemed ok,??? went on my way, got home parked the truck and went about my evening. came out next day to leave and truck wouldn't move in reverse, forward but not reverse. long story short I was told that the snap ring internally probably came out, I have heard of this being a big issue with these, so I set up for it to be rebuilt, got it back and installed and still same issue, what the crap so I ended up having to pull it back out and amongst my own trouble shooting I found the simple issue and was the nylon riders on the 4hi/4low shifter fork were completely gone and allowing the planetary group to free float in and out of 4x4 neutral!!! NOW on to the issue at hand. so far only thing has been done is rebuilt and those fork riders replaced.
now I can move but 2-3 upshift under a load(more noticeable) has a delay going from 2nd to 3rd and under a load it hits hard. I talked to the guy that rebuilt it and he said that the rebuild kits don't always the right springs for the valve body and causes shift issues, so he talked me into the shift corrector kit which I researched and did see what he was saying, so had that done and still no better, still does it, however, it does shift into the gear softer but didn't fix the delay or the hitting hard when it did finally go into 3rd.
After being forced to drive it that way I have since determined that what it happening is it is coming out of 2nd with a second and half pause and then shifting into 3rd, the hard shift comes in to play because during the delay the torque convertor is locking up making it a direct drive like popping the clutch on a standard!!!
I just swapped out the sol pack and I heard from a youtube video that the bolt next to the 2-3 upshift valve on the valve body could be to tight and making a sticky valve, so I re-torqued all the bolts and nuts put all back together and test drive proved to be worse, I now have same issue in all upshifts. all hit hard now, I am at a loss and don't know where to go from here, I can only imaging the sol pack is causing this but I have yet put my org one back in to see... oh and I found two bolts on the accumulator stripped and found one non torqued bolt on the main valve body!!
Hyundai - Accent - Transmissions :: 2003 - Struggling To Shift / In Gear Suddenly Accelerate?
Ozzy is a 2003 Hyundai Accent with an automatic transmission. Over the last 2 year he has been having a lot of problems with his transmission. The first thing that was done was to replace his transmission fluid. Unfortunately the chuckle head that replaced his transmission fluid put the wrong kind in and he had to have a whole new transmission installed. And now only about a year later Ozzy is having transmission problems yet again. What is happening is that it feels like the car is struggling to shift gears and then once in gear it will suddenly accelerate.
Also, the idle races even when your foot is not on the gas pedal and yes, the check engine light is on. So, I have a couple of questions. First how much longer can she keep driving it like this before the engine falls out somewhere on the 405? Secondly how much is it going to cost to repair Ozzy? Also her driving the car when it is behaving this way is really dangerous, right? Because it felt pretty scary today when I was sitting in the passenger's seat and we were doing 75 on the freeway and Ozzy was shaking and making all sorts a noise. And lastly, she needs a new mechanic right, there is no way she should keep going to these guys that put the wrong fluid in and then replaced her transmission, right?
Accent LC (2000-05) :: 2003 - Shifter Moves Around In Gear
So long story short I picked up a 2003 Hyundai accent 5 speed 80xxx miles for $1,000 almost two years ago, vehicle has been running great but the shifter always felt loose and it feels really weird going into second (kinda like the shifter really falls far into gear) I was online searching and found other different type of Hyundai vehicles with the same issue and they replace the shifter bushings oem or after market and fixes the issue. I called hyundai and gave them my vin and they told me for my vehicle they don't sell the bushings , i would need to buy a whole new cable.
My questions is am I looking at the correct place to replace my shifter bushing on the trans or is there something else I should be looking at? Shifter has been getting to the point where it hurts my wrist to shift, I've already replaced the trans fluid and its not hard to go into gear, just feels loose and if I try and go fast and shift fast the car will probably grind second due to the shift lever.
Ford F-150 - 1997-2003 :: 2000 5.4L 4x4 - OD Hard Shift / Slams Into Gear When Give It Little Gas
I have a 2000 F150 5.4l 4x4. When I am going over 50 on the highway and I am in OD, if I let off the gas a couple of seconds later it feels as though the brakes come on because the truck slow down so drastically and when I give it a little gas it slams into gear. It feels as like there is a "gap" where nothing is engaged before it slams back in. This is a rebuilt tranny with less than 7K miles on it. I took it back once and they said it was the motor mounts. I had those replaced and still the same problem. I replaced the spark plugs 6K miles ago and the COPs 3K ago. There is 170K on the truck. I only drive about 8K miles a year.
View 2 RepliesGolf/GTI VI :: 2010 - Bad Grinding When Shift From 1st To 2nd Gear
when i shift from 1st gear to 2nd gear, above 2500 rpms i get a really bad grinding, i am just under 50,000 miles so it is going to the dealership to get fix. It also kicks me out of second gear some time.
View 24 Replies3000GT/Stealth :: Grinding When Shift Into Reverse And Car Won't Go Into Gear
Buying a vr4 this weekend with dr650 turbos... The only problem with car is when you shift into reverse it grinds and won't go into gear, I'm thinking its the reverse synchro?
View 2 RepliesFord Transmission :: Grinding Noise Then Shift Into Gear?
I have a f1ta 5 speed trans on my 4.9 and when i press the clutch in and shift into 1st gear it makes a grinding noise then goes into gear after a little patience. but if i press the clutch and wait a few seconds, then shift into 1st its fine and goes right in.... maybe syncronizers not meshing or they're worn? or could it possibly be a low fluid prob? idk, it just started happening.
View 3 RepliesGolf IV / Jetta IV :: Transmission Grinding When Shift Fast From 2nd To 3rd Gear
Have a question when I shift slow from 2nd to 3rd my o2j tranny doesn't grind but when I shift fast from 2nd to 3rd it grinds it happens starting at 3000 Rpms thru 6000 Rpms. It also doesn't happen when I shift from 4th to 3rd. Have performed a tranny fluid change. Along with replacing the clutch at 1500 miles ago. The engine is AWP.
View 4 RepliesSonata NF (2006-10) :: 2008 - Grinding Noise When Shift From First To Second Gear
I am now getting a grinding noise when I shift from first to second gear. It sounds like the two metals rubbing each other. Its not happening all the time, but for the past two days a bit frequently
I had reported this grinding noise when I turn left a month back. Was thinking because of my worn out tyres, but apparently not.
Accent MC (2006-11) :: Clutch Went Out - No Reverse / Goes Into 1st Gear After Lot Of Coaxing And Grinding
Ok, so I got my car at 60k miles, and the clutch went out almost instantly so I had the entire clutch replaced, and it was working just fine until now. It has been 25k miles since I did the full clutch replacement so it shouldn't be messing up again already. It is not going in to reverse at all, it goes in to 1st gear, but only after a lot of coaxing and grinding, and the clutch feels strange. The clutch is too soft (too easy to push down), but after a while it seems to get better.
2007 Hyundai Accent GS
Manual, hatchback
85k miles
Ford Transmission :: 1989 F350 - Harder To Shift / Grinding Noise Like It Doesn't Want To Go In Gear
I have a 1989 F-350 7.3 IDI with a ZF-5 trans. Lately, I noticed that it was a little harder to shift my truck through gears while driving than it normally is, and when I'm stopped and try shifting into first gear or something it like vibrates and makes like a grinding noise like it doesn't want to go in gear. For a while, I've also had to push on the clutch very hard in order for it to I guess hit the linkage and start, but I never had problems shifting until lately.
Today though, I went to start my truck, I pushed on the clutch as hard as I could, and the switch would not engage so I couldn't start it. So, I guess the switch was farther to link than the pedal could possibly go. I went under the dashboard and engaged it by hand then it started. I drove home and the shifting was still iffy. How can I make the switch engage normally again so its closer I guess and so I don't have to push so damn hard on the clutch to get it to start? And could the switch linkage have anything to do with the shifting being funky lately, or could that only be the clutch itself?
Accent LC (2000-05) :: Grinding Noise While Driving
So I have a 2000 Hyundai Accent, 1.5L with an automatic transmission. I'm hearing a grinding noise when I'm driving. It gets faster as the car goes faster, but the engine RPM has no effect only the speed of the car.
I got new tires, changed the CV axle shaft on both sides, and I also changed the front struts as I was told that one of the struts was bad the last time I took the car for an alignment. None of that has had any effect on the grinding noise.
Then I jacked the car up on both sides and let the wheels spin, and the grinding noise is present that way as well. Then I jacked up just one side at a time. When the driver's side wheel is spinning, the noise is audible, but not when just the passenger side is spinning.
I then disconnected the brake caliper from the driver's side and held it up with a tie wrap to keep it out of the way. The noise is still audible when the wheel is spinning, so it's not the pads or a clip or anything like that.
So now I'm down to a couple of ideas.
1) Wheel bearings
2) Something is hosed in the differential or transmission. I'm guessing that the differential is more likely, as the transmission should effect both sides the same, right?
I'm going to check the wheel bearings now, though to me it seems unlikely to be the problem.