Ford Transmission :: 1996 F250 Will Only Shift To 3rd Gear
On my 96' F-250 4x4, The tranny will shift to 3rd gear and that's it. If I put it in Neutral and then back into drive it will stay in 4th gear for about 15 seconds then go back to 3rd. What could be causing that?
View 14 RepliesFord Transmission :: 1985 F150 C6 Won't Shift Out Of First
My 85 300 cid with a C6 trans won't shift out of first. Seems like this happened several years ago and it was a vacuum diaphragm or something like that. Is this user fixable or do I need a transmission shop to look at it?
View 2 RepliesBmw :: 1985 - Manual Trans Will Not Shift Into 1st, 3rd Or 5th Gear
My 1985 BMW 635, standard transmission suddenly developed shifting problem. It will not shift into 1st, 3rd or 5th gear. It will shift into reverse,2nd and 4th gear. The car is not driven on any frequent schedule, infrequently. I can't remember the last time the transmission oil was changed.There has not been any mechanical distress,grinding of gears,etc. you just cant engage those gears. They all are moving the shifter from neutral to a up position. Is it possible that sludge could be blocking the movement of the synchronize r?
View 2 RepliesFord Transmission :: 1986 - Replaced Torque Converter Now AOD Transmission Won't Shift Out Of 1st Gear?
Replaced Troque Converter, Truck runs engine runs fine transmission won't shift out of 1st gear.
View 2 RepliesFord Transmission :: FMX Transmission Will Not Shift In To 3rd Gear
I have a Ranger that I have put a 302 engine with an FMX transmission in...everything seems to be working correct except the transmission will not shift in to 3rd gear... don't know alot about transmission.. could this be a linkage adjustment issue?
View 6 RepliesFord Transmission :: 1999 F250 Will Not Shift Out Of First
1999 F250 super duty 5.4L 4x4 103000 miles. Just started yesterday going to work will not shift out of first.
I can pedal shift it. and then it is ok till come to stop . Start all over again.
Trans 4R100 automatic
Trans has never been touch from day one .
No engine light and nothing on shifter as for flashing light.
I would like to no what the problem is and about what it would cost to fix I am not going to try to fix this myself i can not do that.
Ford :: Automatic Transmission Sometimes Not Shift Into First Gear
I have a 36 foot motor home on a 2000 Ford F53 chassis. (similar to single axle freight trucks and school busses) After getting one set of the rear wheels partially stuck, which resulted in some spinning of that side, the overdrive off light on the shift lever began to blink and the service engine soon light came on. The fault code said, "speed sensor showing more than one mile per hour". Now the automatic transmission sometimes will not shift into first gear after stopping and has to be manually downshifted, after which, it works fine.
View 1 RepliesFord Transmission :: 4R70W - No First To Second Gear Shift
Working on a 2004 E-250 van. [URL] ....
I went through this transmission completely, its back in the van and I get no 1-2 shift.
when I first put it together, I missed the hole in the flex plate for the torque converter stud and started tightening the bell housing bolts down, I heard loud "POP" and realized what I had done. maybe I damaged the pump?
forward and reverse engagement is firm, both give a nice bump when it goes in gear. This tells me the forward clutch is working, but the intermediate clutch is not applying to make second gear happen.
I have done all the easy stuff I can think of, replaced the shift solenoid and put in a new 1-2 accumulator piston. I guess i need to air check the intermediate clutch piston again and make sure its applying. this a 2004 model trans, so it has the new style pump and intermediate piston.
Ford Transmission :: 4r70w - Truck Tries To Shift Into 4th Gear
I have a 2005 ford expedition with 91000 miles, it has the 5.4 w/ the 4r70w transmission.
For some reason when my truck tries to shift into 4th gear, the RPM's climb to approx. 3000 rpms (meanwhile the truck is not gaining speed) and slowly drops down to about 1000-1500. once the rpms drop down fourth gear eventually engages and I can go about my business as normal as long as I do not let my mph drop too low.
If I turn O/D off, the truck drives perfect, minus not having overdrive.
If I come to a dead stop and put the truck in 2nd gear, with O/D on the truck drives great and it has good engine braking so I am assuming that the band is holding.
I took it to a transmission shop to have some diagnostic checks done, they told me that fourth gear was barely engaging and that they would have to tear apart the transmission to diagnose it further, I told them not to disassemble the transmission.
So I changed out the torque converter (which I assumed was "fourth gear") and changed out all the fluid, the fluid looked a little burnt but there was no debris in the pan but there was some silver material on the tranny pan magnet, and installed a new filter. and the problem still exists.
Ford Excursion :: 2000 - Transmission Won't Shift From 1st Gear?
I have a 2000 Excursion w/ V10 and I have an issue with the transmission form time to time. some times it does not want to shift out of first. if I pull over and turn it off for a few minutes it will be fine for a while and it doesn't do this all the time. A few nights ago it did this so I pulled over and turned it off and it still did it but then it started shifting on its own just fine till we got on the high way which is started shifting in and out of over drive going around 60-65 MPH. didn't want to go too fast not knowing what it could or would do. it did this for a few miles then it started working fine. next day it did the same thing not wanting to shift out of first then started working fine. drove it around last night and it all worked perfectly. The CEL is on but I get a no communication text from the scanner so that is another thing I need to look in to. I'm guessing it is an electrical issue being when it works it shifts fine and it does not slip at all.
View 14 RepliesFord Transmission :: E350 - Auto Gear Shift?
How the auto gear shift works on a ford E350.Does it work by wires or does it have a steel column to change the gears.I have looked for pictures but with no luck. I have spent 2 hours looking.
View 4 RepliesFord Transmission :: Grinding Noise Then Shift Into Gear?
I have a f1ta 5 speed trans on my 4.9 and when i press the clutch in and shift into 1st gear it makes a grinding noise then goes into gear after a little patience. but if i press the clutch and wait a few seconds, then shift into 1st its fine and goes right in.... maybe syncronizers not meshing or they're worn? or could it possibly be a low fluid prob? idk, it just started happening.
View 3 RepliesFord Super Duty (1999-2016) :: F250 Won't Shift Into Any Gear
Friend parked his well working truck and when starting it up after sitting a few days it won't shift into any gear. Lever moves as normal but the truck won't move. A soft clicking sound is the only difference to be noticed when shifting the lever. where to start? Temps are below freezing here if that matters.
View 11 RepliesFord Transmission :: 1993 F250 - Sometimes No Shift Until Lift The Throttle
I have a 93 F250 diesel 4X4 with the automatic, the transmission was rebuilt by a reputable shop les than 10000. miles ago, every few months it will act up, it will act like I put it in neutral then it slams back in gear, then it shifts very hard, sometimes it will not shift until i lift the throttle. Sometimes I can shut it off and when i start it again it will be back to normal, other times it will do this for a few days, then work fine for another month or two.
View 5 RepliesFord Transmission :: 1982 F150 - Slow To Shift Into Any Gear
My 82 f150 4x4 302 c6 trans is acting up. My c6 is slow to shift into any gear when I shift the column shifter, after a moment it jerks into gear, also it doesn't seem D is doing anything but all the other gears seems to function manually or auto.
Fluid level looks ok, maybe a little high on the dipstick. I'm going to check the modulator and do a fluid/filter change but looking for a link to the band adjustment screw ?
Ford Aerostar :: 1998 - Transmission Won't Shift / Stay In 1st Gear
It's a 1988 with a 3.0 engine and an automatic transmission. It doesn't want to shift. I can make it shift manually, but if I leave it in OD, it wants to stay in 1st gear . If you fiddle with the accelerator, you can get it to shift. Then it wants to stay in 2nd, and so on.
Like I said, if I use the gear selector to manually shift, it will go to all four gears just fine.
My thoughts are a vacuum leak (a big one) or a faulty vacuum modulator at the transmission. No, the vacuum line to it doesn't have tranny fluid in it, but I replaced it, and I wonder if it's bad. Yes, I made sure to put the little metal pin/link back in it.
Ford Excursion :: Tightening Transmission Gear Shift Selector?
Fix a Loose Column Shifter on Ford Vehicles - YouTube
The first pic shows the torx screws that come loose, allowing the handle to get sloppy.
The second pic shows the black plastic adjuster wheel that centers the gear shift selector needle on the proper designated gear displayed in the indicator window.
Ford Super Duty (1999-2016) :: 2001 F250 V10 Won't Shift Out Of Low Gear?
I may be going to look at a 2001 F250, 4x4 with a V10 engine tomorrow. I think it is a shop truck for a business. The owner said that the mechanics told him that the trans won't shift out of low gear. It is an automatic. Maybe something as simple as a modulator valve (do they still use them)?
View 4 RepliesFord Transmission :: 1970 F250 - Slow To Shift Going From Neutral To Reverse Can Take Almost 30 Sec When Hot
I have a 1970 f250 with a factory 390 (vin verified) and a C6, I believe the transmission was rebuilt but have no way to verify. It works fine while cold and mildly warm. Once heat soaked it is very slow to shift (going from neutral to reverse can take almost 30 sec) and leaks profusely from the front. I can not tell exactly where the leak is. Could this be a case of just having too much fluid or is there a more serious concern? The dipstick does read high but level ground in my area is hard to come by so the accuracy can be questioned. If it does have to much fluid, do I just drain the pan, re-install and let it run till hot and replace fluid as needed or should I drain and replace with 3 qrts prior to starting?
View 7 Replies