Lexus GS 2006-11 :: 2008 Metal Grinding Noise In 2nd Gear
I am having several issues. I got the lexus dealership to service my transmission recently. I got it back with a weird smell. It smells like body odor. I had to reach out to hendrick corporate for them to address the problem without charging me. Turns out it was the fluid they used. I could smell the smell from inside if i wasn't recirculating the air. They changed the fluid again and it still smells. Is my transmission doing this because it is too hot?
This smell was never an issue until after the first transmission service. And now I'm hearing a metal grinding sound in 2nd gear past 4600 rpm. It still shifts smooth but 2nd gear might be slipping. Something just doesn't seem right. o yea they gave me my car back with my brakes sticking after stopping in traffic. I took it back and was told my brake pads in the rear lost 2mm in less than 650 miles.
By the way this sound can be heard in 1st but is more prevalent in 2nd. It is not heard in any other gears. And when in sport mode the sound instantly stops when i shift up into 3rd.
Ford Transmission :: Grinding Noise Then Shift Into Gear?
I have a f1ta 5 speed trans on my 4.9 and when i press the clutch in and shift into 1st gear it makes a grinding noise then goes into gear after a little patience. but if i press the clutch and wait a few seconds, then shift into 1st its fine and goes right in.... maybe syncronizers not meshing or they're worn? or could it possibly be a low fluid prob? idk, it just started happening.
View 3 RepliesSonata NF (2006-10) :: 2009 - Gear Grinding In Neutral And Park
My 2009 Sonata, 2. 4 L engine, base model with automatic transmission started up and ran OK, but 20 minutes later when I parked the car and shifted towards Park the gears grinded in neutral, stopped grinding in Reverse, and then grinded again when I made it to Park, and I quickly turned off the engine.
When I restarted, it grinded in Park, OK past Reverse, Grinded in Neutral, and then OK in Drive. How serious this is, or if there is anything I can check out on my own?
Ford Transmission :: 1989 F350 - Harder To Shift / Grinding Noise Like It Doesn't Want To Go In Gear
I have a 1989 F-350 7.3 IDI with a ZF-5 trans. Lately, I noticed that it was a little harder to shift my truck through gears while driving than it normally is, and when I'm stopped and try shifting into first gear or something it like vibrates and makes like a grinding noise like it doesn't want to go in gear. For a while, I've also had to push on the clutch very hard in order for it to I guess hit the linkage and start, but I never had problems shifting until lately.
Today though, I went to start my truck, I pushed on the clutch as hard as I could, and the switch would not engage so I couldn't start it. So, I guess the switch was farther to link than the pedal could possibly go. I went under the dashboard and engaged it by hand then it started. I drove home and the shifting was still iffy. How can I make the switch engage normally again so its closer I guess and so I don't have to push so damn hard on the clutch to get it to start? And could the switch linkage have anything to do with the shifting being funky lately, or could that only be the clutch itself?
Sonata NF (2006-10) :: Soft Click From Gear Shift
I have a 2010 Sonata 2.4 with 63k miles and auto trans. Just recently I have noticed a single soft click when braking, just before the car comes to a dead stop. I can hear the click and also feel it in the gearshift.
View 4 RepliesHyundai - Sonata :: 2006 - Spill In Gear Shift, Now No Upshifting
I have a 2006 hyundai sonata, which has possibly the worst designed cup holder of all time. Because of this awful design flaw, I stopped my car at a light yesterday and some of my coffee spilled into the gear shift box. Now when I am in regular D, it appears the car stays in 1st gear. This sonata also has the option of pushing the stick to the right so you can manually shift gears.. I think it's called sports mode or something. When I try that, I can shift it up to 2nd, but I drops right back down to 1. I left it overnight, hoping it was just some wet electronics and would dry, but this morning the problem persists. Not sure if there's a fix for this, if I should take it to a transmission place, or just my regular mechanic. Someone suggested contact cleaner, which I might have I just have to look.
View 10 RepliesSonata NF (2006-10) :: Illumination Of Labels On Gear Shift Panel
I think the gear shift letters (P, D, N, R) are supposed to be illuminated on my Sonata, so there must be a light bulb out. Need to confirm that there is a light under there and tell me how to replace it?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Loud Gear Meshing Like Grinding Noise - Delayed Hard Shift 2 - 3
I have an early 99 F250 4x4 7.3L..... 4R100....
Brief history, a while back on way home from work I let off of the accelerator and had a loud gear meshing like grinding noise, got back on the accelerator and went away, let off and back, so I quickly stopped and pulled over, went through the gears and reverse, everything seemed ok,??? went on my way, got home parked the truck and went about my evening. came out next day to leave and truck wouldn't move in reverse, forward but not reverse. long story short I was told that the snap ring internally probably came out, I have heard of this being a big issue with these, so I set up for it to be rebuilt, got it back and installed and still same issue, what the crap so I ended up having to pull it back out and amongst my own trouble shooting I found the simple issue and was the nylon riders on the 4hi/4low shifter fork were completely gone and allowing the planetary group to free float in and out of 4x4 neutral!!! NOW on to the issue at hand. so far only thing has been done is rebuilt and those fork riders replaced.
now I can move but 2-3 upshift under a load(more noticeable) has a delay going from 2nd to 3rd and under a load it hits hard. I talked to the guy that rebuilt it and he said that the rebuild kits don't always the right springs for the valve body and causes shift issues, so he talked me into the shift corrector kit which I researched and did see what he was saying, so had that done and still no better, still does it, however, it does shift into the gear softer but didn't fix the delay or the hitting hard when it did finally go into 3rd.
After being forced to drive it that way I have since determined that what it happening is it is coming out of 2nd with a second and half pause and then shifting into 3rd, the hard shift comes in to play because during the delay the torque convertor is locking up making it a direct drive like popping the clutch on a standard!!!
I just swapped out the sol pack and I heard from a youtube video that the bolt next to the 2-3 upshift valve on the valve body could be to tight and making a sticky valve, so I re-torqued all the bolts and nuts put all back together and test drive proved to be worse, I now have same issue in all upshifts. all hit hard now, I am at a loss and don't know where to go from here, I can only imaging the sol pack is causing this but I have yet put my org one back in to see... oh and I found two bolts on the accumulator stripped and found one non torqued bolt on the main valve body!!
Hyundai - Sonata :: 2006 - Gear Shift Lever Wet / RPMs Went Up High And Car Barely Moving
I had to stop quick today. My ice water spilled into the gear shift lever. A mile down the road my rpms went up high and the car barely moving.
2006 Hyundai Sonata...
Sonata NF (2006-10) :: Grinding Noise At Low Speed
Just put on eibachs and car is randomly making a grinding noise when slowly accelerating or braking.. Also noticing a fairly loud clicking noise when going in reverse. The noise isn't consistent and seems to happen more right after startup. I haven't gotten the alignment done yet and was wondering if this could be the problem. Will try and post a video soon.
View 8 RepliesSonata NF (2006-10) :: V6 - Grinding Noise On Startup
I just bought a 2006 Sonata LX V6 a few days ago and in almost every way it seems like a great car. My '08 GLS V6 which gave me 150k great miles got totaled in November, which really sucks, but I wanted to find another '06-'08 V6. I noticed when I started it for the test drive that the car made a bit of a grinding noise on start up. I didn't think much of it and figured that the warranty from the dealership would cover any problems.(I probably should've checked earlier, but the dealership's warranty only covers cam and lifter noise and engine failure) After I looked into the issue more, I found out that it is a fairly common problem on the early 3.3's with the timing chain tensioners. I'm pretty concerned based on just the nature of the repairs and the cost I've seen for them.
I'm the third owner so the 5 year/60k warranty is expired, but I know there is a TSB out for the issue. I can't find the TSB anywhere but I've heard to have it repaired the car has to make the noise on start, sit 10 minutes, and make the noise again. If it does, the oil needs to be changed and the test repeated again. Since I'm running Hyundai 5W-20 and an OEM filter already, I tried the test on my own. It made the noise on start, sat 10 minutes, and made it again. It is only for a couple seconds, but it's still concerning to me. I guess what I'm trying to ask is if what I've described is covered under the TSB. I really don't wanna have to worry about something like that right now, so my next question is whether the issue I have is detrimental to the motor. My worst fear would be to have the chain jump a cog on the cam gear and slam valves into pistons.
Sonata I45 (YF - 2011+) :: Braking Noise When Coming To A Stop Near Gear Shift Lever
I have a 2011 Sonata with 4,000 miles. Recently, I have noticed that when coming to a stop, I hear a light thump noise in the center console area near the gear shift lever. If I put my hand on the gear shifter, I can feel it move ever so slightly at the time of the noise. The noise is very repeatable. If I take my foot off the brake and start rolling and then I reapply the brake (either softly or hard) it will make the thump noise. It is not very loud and can be drowned out with loud music, but if listening to news, it is very noticeable and annoying in city traffic, where stops are very frequent. I put the car up on ramps and looked underneath and did not see anything noticeable. It will probably require the center console between the seats to be removed.
View 14 RepliesSonata NF (2006-10) :: Grinding Noise At Cold Startup
Need to determine the noise before I took the vehicle in to be serviced. I don't know if I would necessarily describe this as grinding...to me it doesn't sound like metal on metal..but it's not normal.
Only happens on a cold startup, and even then it hasn't been 100% of the time...probably 80% of the time though.
2007 Hyundai Sonata - Startup Noise - YouTube
I found this thread, Grinding Sound On Statup but not sure it's the same issue. This just started. Vehicle has 150K miles on it.
Sonata NF (2006-10) :: Grinding Noise Only Occur When Car Is Moving
Have a '06 V6 GLS w/ approx 105K miles. About a week ago I started hearing a noise. The noise sounds a lot like a brake pad wear indicator, metal grinding on metal. However, the noise does not seem to be related to use of the brakes. The noise only occurs when the car is moving. It is intermittent. Comes from the front of the car. Seems to usually occur when making a sweeping or gentle right turn. Speed does not seem to matter - can be going 20 to 60 mph. Noise will last from less than a second to as much as 5 to 10 seconds and then goes away.
I have taken a cursory look at the crankshaft damper pulley and it appears to be ok...
Lexus GS 2006-11 :: 2008 350 AWD -VSC And CEL Came On, Auto Trans Won't Shift Past 4 Gear
My VSC and check engine light have come on. In addition now the auto trans will not shift past 4 gear with in auto or with me doing it manually. My local shop who has worked on this car before and is very good put the computer reader on it and got a P0500 for vehicle speed sensor "A". Today they put it on the real monitor and it reads a different code that says check engine code but does not reveal the code to read.
I really don't want to go to my dealer and get it hard. The car has 175,000 and until now has run great. I tried the gas cap fix to no avail. The shop did a reset when i first got there and it last 75 yards.
Sonata NF (2006-10) :: Loud Grinding Noise When Press Down On Clutch
I have a 2009 Hyundai sonata, 2.4, 5 speed manual, gls, when I press down on clutch whether from a stop or when shifting, I get a loud grinding noise and the radio goes dead at same time!, I know it is the starter attempting to "engage", at least that's what I believe it to be, it also "'starts "from, the "on " position when I press on clutch.
View 8 RepliesSonata NF (2006-10) :: Grinding And Banging Noise When Driving At Low Speeds
A few days ago, my Sonata 2006 LX started making weird noises when driving at low speeds. The noise comes from the front driver's side area, they are not affected by steering or going over bumps. Usually get less intense when I accelerate or brake. At speeds around 5 mph, the noise is grinding and pretty loud. At higher speeds, it's more like banging and it's frequency increases with the speed. There was no effect other than the noise, but the last day at higher speeds, I can feel with the steering wheel a little vibration sometimes from the banging.
I've been having tough times renting a car during the weekend and I still drive on short distances, but I'm afraid it could be a safety issue or that I can be making things much worse to repair. The noises got worse since the beginning, but I don't think they are getting any worse anymore.
Sonata NF (2006-10) :: Grinding Noise That Would Stop When Press The Clutch In
Long story..couple months ago while coming home my 08 Sonata 2.4L manual 84,000 miles...started making this grinding noise and would stop when I pressed the clutch in and then sounded like something was grinding near the passenger front wheel.. well I get it home and the next morning my husband and I ride up the road so he can hear it.. was going to take it to the shop but it stopped and ran just fine till the other day.. crank the car and its fine.. once it gets warmed up and a few miles down the road it makes a knocking noise...but only when I let off the gas or idling .. even pressing on the gas just a tiny bit made it stop (even tried in while parked in the driveway with the hood up to make sure the engine wasn't just drowning it out) well I took it to the local dealership today and they said it was the flywheel and that it and the clutch and bearing needed to be replaced..
View 3 RepliesSonata NF (2006-10) :: Loud Grinding Noise Coming From The Left Side
I just got the car back from repairs, there was a loud grinding noise coming from the left side of the engine. It turned out the whole rack and pinion setup was pouring out fluids and needed to be completely replaced also while it was in there they checked out an oil leak which ended up being the front valve cover and replaced a dead O2 sensor. The car has 99,300 miles
View 6 Replies