Ford Super Duty (1999-2016) :: 2006 F250 - Manual Hubs Are Very Hard To Rotate
My manual hubs on my 2006 f250 have become very hard to rotate so I would like to replace them. I saw that bronco graveyard has Warn hubs for a Dana 60 front axle. Is this what I need? My door sticker with the axle code is illegible, and I want to make sure I get the right hubs.
View 5 RepliesFord Super Duty (1999-2016) :: F250 - Hard To Turn Left
I have a 1999 f250 sd with the 7.3. I'm not sure what is going on with my pickup. When I turn to the right i can turn with one finger, but when I turn left i have to put some muscle into it. Power steering fluid is full. I raised the front end and it turns both ways easy. My ball joints feel fine, there is no tire shake when i have it off the ground. My tie rods feel fine also, nice and tight. I was thinking about replacing the steering sector to see if thats the issue but wanted to get a second opinion first.
View 2 RepliesFord Super Duty (1999-2016) :: 2012 F250 XLT - Passenger Side 4x4 Hub Little Hard To Turn
About a month ago I bought a 2012 F250 XLT. I just had it inspected (PA laws) and found that the passenger side 4x4 hub is a little hard to turn. There is also alot of corrosion on that side. I will be taking care of the corrosion, but have not had a newer 4x4 hub apart yet and was wondering for pictures or any diagrams? I would like to take care of it before winter hits.
View 3 RepliesFord Super Duty (1999-2016) :: F250 - Hubs Won't Unlock / How To Get Them Functional
I just got a 99 F250 PSD, it had not been in 4wd in a while, now the hubs won't unlock.
My 01 F250 seemed to have strictly manual hubs. Turn right to lock, left to unlock. They may have been aftermarket, but on by the PO. Do I need to put some new Warns on the 99? Or can I lube then up and get them functional.
Ford Super Duty (1999-2016) :: Clunking In Front End When Turning Hard Even With Hubs In Auto
So I noticed the past few days my 09 F250 was clunking in the front end when turning hard even with the hubs in auto so I knew there was an issue in there somewhere. This morning I took the jack and found the passenger side would not release no matter which way the lock was turned. Pulled the locking assembly out and found a couple of the pieces of plastic cage broken (truck has 250k miles) which is to be expected I guess but the locking ring that holds the inner piece that slides over the axle stub was off and hanging next to the c-clip on the axle.
So with the plastic of the cage already being broke and the mileage on the truck it's clear I need a new lock for that side.
Here's my dilemma, I have to deliver a conference room table 200 miles away tomorrow morning that they need for meeting tomorrow afternoon at 3:00pm. I cut the rest of the plastic pieces and took the gears out leaving just the cover with the diaphragm and put it back on the hub. I can't come up with any logical reason why I can't drive the truck this way but just want to bounce it off the experts here before I take off on a 400 mile trip in the morning. The only thing I can come up with is if I were to engage the 4wd the vacuum might suck the auto-lock diaphragm in and pop it but otherwise I can't find any reason to not run it this way, the hub is still sealed up and free-wheeling just like if it were in 2wd anyway.
Ford Super Duty (1999-2016) :: 2008 F250 Will Turn Over But Not Crank
I have 08 f250 6.4 was driving down the road truck just died. Will turn over but not crank. I've checked oil level, water level, fuses, fuel cut off switch. Still no start.
View 3 RepliesFord Super Duty (1999-2016) :: 2007 F250 4x4 Not Unlocking The Hubs Automatically
Brings back memories of my many projects from back in the day. Anyway, my uncle has this f250. He said 4x4 wouldn't automatically lock the hubs in. I tested the vacuum pulse valve on the fender and changed it out. Now the hubs will lock in when you turn the light on the dash but it will not unlock the hubs unless you go outside and manually turn the hubs to engage then back to auto. Only then will the front end be unlocked. I notice small puffs of air blowing back from behind the hub themselves so I was thinking it's time to reseal the vacuum portion of the hubs.
View 4 RepliesFord Super Duty (1999-2016) :: 2010 F250 Front Hubs Don't Lock
I have a 2010 F250 with 154000km (96000 miles) that we bought last week. When I was looking it over during the purchase I noticed the front axle didn't lockup in "auto", in manual lock it seemed fine so I figured vacuum leak or something like that. Yesterday morning I was in the yard and got a little hung up in snow drifts so just got out, locked the hubs and switched to 4x4 and I think the front end didn't engage at all.
So later on I had it in the shop installing the two way radio and decided to check the front end out a little more thoroughly. Vacuum lines seem fine, hubs turn fine but I notice the axle shafts both move up and down almost a quarter inch, that seems excessively loose to me. I've been doing some research on the internet and it appears the front hubs are serviced as a unit, also some information seems to point to needle bearings within the actual locking hub mechanism itself?
So the questions:
1. Does that front axle shaft seem excessive? What are the specs?
2. Can I replace bearings and seals only or do these units come only as assemblies? Inner hub, outer hub units? Wheel bearings seem fine.
3. With that much play is there a chance the outer axle shafts are worn also?
Ford Super Duty (1999-2016) :: 2004 F250 - Grinding Noise When Hubs Are Engaged
Okay this is what I got; I recently purchased high mileage 2004 F250 Super Duty short box super cab 5.4 liter. Came with manual 4x4 handle on the floor so no 4 wheel on the fly and this eliminates the vacuum for the auto hubs so this will not be part of the problem. When engaging the hubs and ONLY when engaged the driver side hub grinds. The 4 wheel drive works but it sounds like its ready to grind itself into oblivion. I did pull the hub and the grinding was gone, I happen to have a spare hub that is good and the grinding returned.
I have jacked it up and made sure I have no play in the wheel itself and the axle knuckle on the axle shaft. Some say remove the front drive shaft? Or turn the wheels all the way in one direction engage the hubs and check for binding? I will do this in the morning, but what does that confirm if it not the hub. Could it be the passenger side echoing across? On my 99 Super duty I kept hearing moaning coming from up front like the breaks were shot and if you stuck your head out the window it was the back echoing to make it sound like the front.
Ford Super Duty (1999-2016) :: 2000 F250 - Axle Spins When Hubs Are Unlocked
I have a strange thing going on with my hubs i think. I have a 2000 f250 7.3 4x4 that I just purchased. Lettering on hubs were worn out as far as labeled locked or unlocked so I tried to turn the axel to see what position they were in. Drivers side spun freely but passenger side did not. Both hubs were counter clockwise and turning it to lock didn't change a thing.
Figured it was a bad hub so I jacked the front drivers side up. Spun tire with both hubs unlocked and axle didn't spin. Locked hub on drivers side and axle spun. Indicating the passenger side was unlocked. Then I locked passenger side and wheel would not turn. Ok. That seems right.
Jacked up passenger side front tire with drivers side on ground and axle spins no matter if its locked or unlocked. So does this indicate the hub is good and I should look at something else or could it still be the hub. Axle spins all the time and I don't want to wear anything out.
Ford Super Duty (1999-2016) :: 2001 F250 4x4 - Auto Lock Hubs Are Not Working
2001 F-250 7.3. The auto lock hubs are not working on the truck lock hubs in and all works fine. First thought is the vacuum system has a leak or something of the sort. Had truck at the shop they are telling me the GEM module controls the vacuum to engage the auto hubs and the signal is not coming from the GEM and it need to be replaced. It was the GEM causing the problem.
View 6 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Front Hubs Do Not Engage Automatically
About a month ago I bought a 2004 F-250 160xxx from a reputable Ford dealer here in town. The dealer performed a safety and emissions inspection, and spent about a grand on other repairs, as a condition of my purchase. Today I had it in the shop for an instrument cluster issue (at a different Ford dealer, closer to my house), and was told the vacuum lines were all messed up. Their write up is below:
"Check 4x4 operation. Transfer case shifts to 4x4 and 4x4 low. Front hubs do not engage automatically. Check vacuum at the hubs. No vacuum. Check the vacuum at the solenoid. No vacuum. Perform visual of the engine vacuum lines. There is no vacuum to the reservoir. Vacuum line is routed wrong from the fuel pressure regulator to the vapor management valve. There is other vacuum concerns. All of the vacuum line routing needs to be inspected and corrected."
The service rep told me it is questionable whether the 4x4 ever worked, although during the few weeks I've owned it, I could hear gears or other mechanical parts making noise which seemed to me to be in response to me turning the 4x4 electronic switch. She also said there was a vacuum line dangling loose with a screw in the end of it.
Before I contact the dealer where I bought the truck, I am planning my going-in position. But I wanted to get a sense of a) how serious of a problem this might be? and b) how reasonable it is that the dealer didn't catch this issue before I bought the truck while they were in their fixing other things?
The dealer who sold me the truck made it very clear that the sale was as-is, and I took it to my mechanic prior to purchase, though unfortunately he only had time for a cursory look at the engine. Obviously he didn't look closely enough to find this issue.
I'm not sure if I should ask the dealer who sold it to me to fix it, or ask them to allow me to return it, or sell it back to them, or if I should eat the cost of fixing it. How wrong would it be to try to trade it in for something else?
Ford Super Duty (1999-2016) :: 2001 F250 4X4 - ESOF Switch Not Engaging Hubs?
I have a 2001 F250 4x4 and the ESOF switch not engaging hubs, currently I have no 4x4 lights coming on in the cluster when i turn the switch. I am not experiencing any of the vaccum symptoms that most people are suggesting. I When I turn the switch i also do not hear any relays clicking. Relays have been tested, and i waited for the 45 second transfer delay that the manual mentions. ESOF switch has power, and is working properly (I know because I bought a new one in attempt to fix the problem) Basically I have no responses from any of my 4x4 indicators or parts.
View 14 RepliesFord Super Duty (1999-2016) :: F250 V10 - 4 Wheel Drive Hubs Are Not Working With The Vacuum
I recently picked up a '99 F250 Super Duty with the 6.8L V10 for a song.
The 4 wheel drive hubs are not working with the vacuum. If I use the manual lock on the hubs all is well. I ordered the Innova 31703 CarScan OBD2 + OBD1/ABS/SRS Scan Tool. It says it does Trans codes. I am hoping it will cover the 4 wheel drive too.
Maybe related, the heat is always on. Meaning I feel heat at my feet when the temp dial is cold and fan is off. I can't find the heater control valve to check the vacuum line.
Ford Super Duty (1999-2016) :: 2000 F250 - ESOF Auto Hubs Not Engaging Automatically
I have a 2000 f250 CCSB 4x4 with the ESOF auto hubs. The auto hubs won't engage automatically. They work fine manually. The transfer case is engaging and correct lights are coming on. There is a little bit of vacuum coming from the vacuum switch but it doesn't seem like much to me. All the dash HVAC controls work fine though. I Lubed and cleaned inside the hubs according to Guzzles directions.
While torn down, I blew through the vacuum port on the outside of the hub and there was little to no restriction. I don't think there is enough vacuum to pull the hubs, but is that possible if all the dash controls work fine? What pressure should it take to engage them? My next step is to pick up a vacuum pump and see if I can engage them with it.
Ford Super Duty (1999-2016) :: 2008 F350 - Automatic Hubs Not Working
I have a 2008 F350 and my automatic hubs won't work, also when I turn the AC on there is heat coming out of one side of the vents. I am assuming this is a vacuum leak somewhere but my vacuum pump doesn't run steady? I thought if there is a vacuum leak then your pump should run steady? The 4X4 works fine by locking in the hubs
View 7 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Steering Seems Heavy And Won't Return To Center After A Turn
Just bought this '08 F250 CCSB 4X4 5.4 Problem is the steering seems heavy, it tends to wander at higher speeds and won't return to center after a turn. I've searched on here and found a few possibilities (axle u joints, ball joints, steering gear, etc). I have an appointment with the dealer on Friday to fix it under warranty but he is convinced it's the u joints in the steering shaft seizing. When my F150 steering shaft began to seize, it would be hard to turn then break free then be hard then break free and this is not what is happening on the SD. I haven't had a chance to check the front end myself but not sure how you would check the axle u joints if there was no play in them. How would you check to see if they were seizing up.
View 3 RepliesFord Super Duty (1999-2016) :: 2008 F250 Squeak When Turn The Wheel While Tire Is Spinning
I have a 2008 F250 XLT. When i am driving and turn the wheel a squeak is noticeable while the tire is spinning. as i speed up the squeak gets faster and slower when i slow down. I have it narrowed down to the right front tire but cant figure out what is causing it.
View 5 RepliesFord Super Duty (1999-2016) :: 2013 F250 - Vacuum Lines For Auto Locking Hubs Frozen
I have a 2013 F250 which has both the Manual and auto locking hub feature. I tried to plow my driveway this morning and after making one pass I put the truck in reverse and could not back up my steep driveway. The truck is showing locked in 4x4 on the dash, the 4x4 control is in high lock but the front wheels will not turn. It has been very cold here lately (-30) and I'm wondering if the vacuum lines for the auto locking hubs have frozen. I have switched the control out of 4x4 and back in several times, and it does lock in again, but as soon as I put the truck into reverse, they unlock again. The hubs are covered with ice and snow right now so I have not yet tried to manually lock them.
View 14 Replies