Ford Super Duty (1999-2016) :: 2001 F250 4X4 - ESOF Switch Not Engaging Hubs?
I have a 2001 F250 4x4 and the ESOF switch not engaging hubs, currently I have no 4x4 lights coming on in the cluster when i turn the switch. I am not experiencing any of the vaccum symptoms that most people are suggesting. I When I turn the switch i also do not hear any relays clicking. Relays have been tested, and i waited for the 45 second transfer delay that the manual mentions. ESOF switch has power, and is working properly (I know because I bought a new one in attempt to fix the problem) Basically I have no responses from any of my 4x4 indicators or parts.
View 14 RepliesFord Super Duty (1999-2016) :: 2005 4x4 ESOF - Hubs Seem To Lock Automatically As Getting Binding While Turning?
My 2005 has the ESOF system which has worked flawlessly. Recently I had upper and lower ball joints done and after that repair I had no auto locking hubs. ( independent shop messed up seal install ) they redid the job and it now seems like my front hubs are locking automatically because I am getting binding while turning. So this is the problem.. the front wheels do not "pull" only the rear wheels spin. If I manually lock the hubs I have 4x4 and can get out of being nearly stuck and everything works normally. What is wrong here? Does the shop need to redo the job again?
View 2 RepliesFord Super Duty (1999-2016) :: How Does ESOF Locking Hubs Work In Auto Mode
I took apart, cleaned and lubed my hubs. My question is: how does the vacuum make the gears work?
Does the vacuum force (suck) the nylon assembly to push the outer gear towards the center of the truck, sliding on the inner gear thus engaging the teeth so that the axle shaft turns the hub?
When the vacuum is gone, does spring pressure pushes the outer gear away from the center of the truck thus disengaging the teeth from the inner gear and allowing the hub to free wheel?
Is this vacuum source constant during 4wd and not present during 2wd or do I not understand how the system works? I have read about a “vacuum pulse” that locks the hubs and another pulse that unlocks the hubs and this confuses me.
BTW, I like the way the Auto lock works. I had a set of Warn Auto Lock hubs on my 78 CJ. They worked on the principle of a set of roller bearings that would lock (pinch) when there was torque coming from the drive shaft. There was no vacuum involved at all. The down side was that when you coasted, the front hubs would be in two wheel drive and so you would not get the engine braking on all 4 wheels. These ESOF seem to have solved this problem.
Oh, I should probably tell you that I just purchased my 04 F250 SuperDuty 4x4 with the 6.0 diesel, just had it a week. It has been 18 years since I owned a 4x4. Before this I owned an 87 F250 2wd with the 6.9 diesel.
Ford Super Duty (1999-2016) :: 2007 F250 4x4 Not Unlocking The Hubs Automatically
Brings back memories of my many projects from back in the day. Anyway, my uncle has this f250. He said 4x4 wouldn't automatically lock the hubs in. I tested the vacuum pulse valve on the fender and changed it out. Now the hubs will lock in when you turn the light on the dash but it will not unlock the hubs unless you go outside and manually turn the hubs to engage then back to auto. Only then will the front end be unlocked. I notice small puffs of air blowing back from behind the hub themselves so I was thinking it's time to reseal the vacuum portion of the hubs.
View 4 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Front Hubs Do Not Engage Automatically
About a month ago I bought a 2004 F-250 160xxx from a reputable Ford dealer here in town. The dealer performed a safety and emissions inspection, and spent about a grand on other repairs, as a condition of my purchase. Today I had it in the shop for an instrument cluster issue (at a different Ford dealer, closer to my house), and was told the vacuum lines were all messed up. Their write up is below:
"Check 4x4 operation. Transfer case shifts to 4x4 and 4x4 low. Front hubs do not engage automatically. Check vacuum at the hubs. No vacuum. Check the vacuum at the solenoid. No vacuum. Perform visual of the engine vacuum lines. There is no vacuum to the reservoir. Vacuum line is routed wrong from the fuel pressure regulator to the vapor management valve. There is other vacuum concerns. All of the vacuum line routing needs to be inspected and corrected."
The service rep told me it is questionable whether the 4x4 ever worked, although during the few weeks I've owned it, I could hear gears or other mechanical parts making noise which seemed to me to be in response to me turning the 4x4 electronic switch. She also said there was a vacuum line dangling loose with a screw in the end of it.
Before I contact the dealer where I bought the truck, I am planning my going-in position. But I wanted to get a sense of a) how serious of a problem this might be? and b) how reasonable it is that the dealer didn't catch this issue before I bought the truck while they were in their fixing other things?
The dealer who sold me the truck made it very clear that the sale was as-is, and I took it to my mechanic prior to purchase, though unfortunately he only had time for a cursory look at the engine. Obviously he didn't look closely enough to find this issue.
I'm not sure if I should ask the dealer who sold it to me to fix it, or ask them to allow me to return it, or sell it back to them, or if I should eat the cost of fixing it. How wrong would it be to try to trade it in for something else?
Ford Super Duty (1999-2016) :: 2001 F250 4x4 - Auto Lock Hubs Are Not Working
2001 F-250 7.3. The auto lock hubs are not working on the truck lock hubs in and all works fine. First thought is the vacuum system has a leak or something of the sort. Had truck at the shop they are telling me the GEM module controls the vacuum to engage the auto hubs and the signal is not coming from the GEM and it need to be replaced. It was the GEM causing the problem.
View 6 RepliesFord Super Duty (1999-2016) :: ESOF - Hubs Won't Disengage
I've read many posts about ESOF and fault vacuum lines and how that will prevent 4x4 from engaging. I experienced a different problem this past weekend. Here's the situation...
Was about 1.5hr drive up to the mountains. Outside temp when we left the house: 10F. Outside temp when we arrived at destination: 9F. Quite a bit of road grime on the way up from sand, slush, and that magnesium chloride (or whatever they hell they put on the roads in an attempt to keep it from freezing). 4x4 worked fine on the way up. 4x4 light on dash was on, and I KNOW I could not have climbed the snow-covered forest roads without being in 4x4. Also, I could hear and feel the front hubs turning.
On the way home, once I got to where the roads were sufficiently ice free, I turned the dial on the dash back to 2WD. 4x4 light goes out. But I can hear and feel the front hubs are still turning. Toggled the switch back and forth a few times. 4x4 light would come and go with the toggled switch. But the hubs didn't disengage.
When I got back into town (outside temp now about 5), we stopped at a red light and I toggled the switch again. This time, the hubs disengaged. Is this a sign of bad vacuum? Or more an indication of faulty hubs??
Ford Super Duty (1999-2016) :: 2013 F250 - Vacuum Lines For Auto Locking Hubs Frozen
I have a 2013 F250 which has both the Manual and auto locking hub feature. I tried to plow my driveway this morning and after making one pass I put the truck in reverse and could not back up my steep driveway. The truck is showing locked in 4x4 on the dash, the 4x4 control is in high lock but the front wheels will not turn. It has been very cold here lately (-30) and I'm wondering if the vacuum lines for the auto locking hubs have frozen. I have switched the control out of 4x4 and back in several times, and it does lock in again, but as soon as I put the truck into reverse, they unlock again. The hubs are covered with ice and snow right now so I have not yet tried to manually lock them.
View 14 RepliesFord Super Duty (1999-2016) :: 4WD Is Only Working Now When Manually Lock The Hubs - ESOF Vacuum Leak
I noticed that my 4WD is only working now when I manually lock the hubs in (they have that options!), and the air blows out the defroster when I shift, so it looks like I have a vacuum leak. Where are the typical leak points on a 2006 F250? What's the best way to confirm a leak (other than just replacing all of the hose)?
View 2 RepliesFord Super Duty (1999-2016) :: 2007 F250 Auto 4x4 Not Engaging - Rear Wheels Spinning / Front Did Not Turn
Yesterday I was parked on an incline with my front wheels on gravel and the rear wheels on wet grass/mud. When I tried to go, the rear wheels started spinning. I then switched on the low 4x4, and tried to go. The rear wheels continued to spin, but the front did not turn. I had new wheels installed, that has a cap that covers the manual locking hub, so I couldn't turn it to lock the hub. What should I look for to fix the problem?
2007 F250 4X4 Larriat SRW
Ford Super Duty (1999-2016) :: 2000 F250 - Axle Spins When Hubs Are Unlocked
I have a strange thing going on with my hubs i think. I have a 2000 f250 7.3 4x4 that I just purchased. Lettering on hubs were worn out as far as labeled locked or unlocked so I tried to turn the axel to see what position they were in. Drivers side spun freely but passenger side did not. Both hubs were counter clockwise and turning it to lock didn't change a thing.
Figured it was a bad hub so I jacked the front drivers side up. Spun tire with both hubs unlocked and axle didn't spin. Locked hub on drivers side and axle spun. Indicating the passenger side was unlocked. Then I locked passenger side and wheel would not turn. Ok. That seems right.
Jacked up passenger side front tire with drivers side on ground and axle spins no matter if its locked or unlocked. So does this indicate the hub is good and I should look at something else or could it still be the hub. Axle spins all the time and I don't want to wear anything out.
Ford Super Duty (1999-2016) :: 2006 - Front Hubs Not Engaging In 4wd?
2006, ESOF. Noticed the front hubs aren't engaging but the transfer case is. What should I check?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: ESOF Won't Engaging Hubs?
I have my vacuum system back up and working and using my vacuum pump I determined my lines are all good. They hold a vacuum fine, but my ESOF isn't engaging my hubs. I guess that leaves either the selector on the dash or the seal at the hubs.
If it is the selector, I should just be able to just disconnect the vacuum line at the selector and use my pump to engage my hubs. How much it is supposed to take to activate the hubs?
Ford Super Duty (1999-2016) :: 2000 F250 - Hubs Click Into Lock Position And Dial On Dash Lights Up
We got a ton of snow dumped on us today and for some reason my 4WD has decided not to work this year. I have a 2000 F250 4WD Triton V10. The hubs click into the lock position and the dial on the dash lights up 4x4 but I am definitively not engaging into 4WD. I'm pissed because this is specifically the reason i bought a 4WD and it's failing me. I can't find a fuse panel diagram to save my life however all the fuses in the interior of truck look to be fine.
View 3 RepliesFord Super Duty (1999-2016) :: Front Hubs Not Auto Locking
My hubs will not lock when put into 4x4. I disconnected all lines from the solenoid to both hubs and tested them for leaks... All good there. I put a gauge on the lines at both hubs one at a time while the other is still connected and get no reading when switched into 4x4. I checked for vacuum right out of the solenoid, and I get 2inHg when switched into 4x.
The vacuum pump kicks on every time I start the truck, even if I just shut it off and re-start right away. There is no delay when switching my ac/heater controls to different settings or vent locations. So I know there is vacuum. How much vacuum I should be getting out of the solenoid to the hubs?
2004 F350 6.0L....
Ford Super Duty (1999-2016) :: 2006 6.0 F350 4x4 Auto Hubs Will Not Engage
I was using 4x4 High the other day and it was working just fine. Now today, I was at my first parking lot to plow and used the ESOF to shift into 4x4 High and it did not engage with the hubs being in auto mode. The lights on the dash show up indicating that I am, but I am still in 2wd.
If I manually lock the hubs, it engages 4wd high. I tried the same thing using the ESOF to switch over to 4x4 low and it does NOT engage either.
I also noticed that heater blower was switching over to full defrost even though I had it set on the floor setting (manual heat climate *****).
Does this sound like a vacuum leak? I haven't had a chance to test the lines yet. Btw, this is my second work truck and not the one listed in my signature below. It's a 2006 f-350 6.0 xlt.
Ford Super Duty (1999-2016) :: Clunking In Front End When Turning Hard Even With Hubs In Auto
So I noticed the past few days my 09 F250 was clunking in the front end when turning hard even with the hubs in auto so I knew there was an issue in there somewhere. This morning I took the jack and found the passenger side would not release no matter which way the lock was turned. Pulled the locking assembly out and found a couple of the pieces of plastic cage broken (truck has 250k miles) which is to be expected I guess but the locking ring that holds the inner piece that slides over the axle stub was off and hanging next to the c-clip on the axle.
So with the plastic of the cage already being broke and the mileage on the truck it's clear I need a new lock for that side.
Here's my dilemma, I have to deliver a conference room table 200 miles away tomorrow morning that they need for meeting tomorrow afternoon at 3:00pm. I cut the rest of the plastic pieces and took the gears out leaving just the cover with the diaphragm and put it back on the hub. I can't come up with any logical reason why I can't drive the truck this way but just want to bounce it off the experts here before I take off on a 400 mile trip in the morning. The only thing I can come up with is if I were to engage the 4wd the vacuum might suck the auto-lock diaphragm in and pop it but otherwise I can't find any reason to not run it this way, the hub is still sealed up and free-wheeling just like if it were in 2wd anyway.
Ford Super Duty (1999-2016) :: F350 Won't Go Into 4 Wheel Drive - Auto Locking Hubs
My F350 4x4 won't go into 4 wheel drive unless I get out and take them out of auto and put them in locked position and when I have it in lock mode it seams to work like it's in auto mode, when I put the switch on the dash in 2wd, it seams like it's only driving the back wheels....
View 14 RepliesFord Super Duty (1999-2016) :: With Auto Hubs Shift On The Fly Selector Is Turned To 4X4 High Or Low?
After reading the book, I'm afraid I still don't understand. When the hubs are in AUTO, & the shift on the fly selector is turned to 4X4 high, or 4X4 low, is the truck in 4 wheel drive. What happened to free or lock.
View 3 Replies