Ford Super Duty (1999-2016) :: 2008 F250 - How Hard Should It Be To Turn Hubs
On my 2008 f250 I can not turn the hubs without a set of pliers...does that mean I need new hubs....
What auto tranny do I have with the 5.4.. is it a six speed...
Ford Super Duty (1999-2016) :: 2012 F250 XLT - Passenger Side 4x4 Hub Little Hard To Turn
About a month ago I bought a 2012 F250 XLT. I just had it inspected (PA laws) and found that the passenger side 4x4 hub is a little hard to turn. There is also alot of corrosion on that side. I will be taking care of the corrosion, but have not had a newer 4x4 hub apart yet and was wondering for pictures or any diagrams? I would like to take care of it before winter hits.
View 3 RepliesFord Super Duty (1999-2016) :: 2008 F350 4WD - Clicking Noise Only When Turning Hard Left
'08 F350 6.4l 4wd, I had the truck come in with a exploded transfer case. (See pics). Ive read all about this happening to many others. The truck still drove, hubs not locked, plenty of fluid in the TC, pretty sure it was the double Cardan that did it. Anyways I replaced thwith TC, replaced the front driveshaft, filled the TC with recommended fluid. Test drove and drives great, shifts fine. Only until I turned left.
At slow speeds turning hard or 15-20 taking a turn, it sounds like a ratchet clicking from somewhere on the left side, right around the drivers door, from what I can hear from the cab. Does it in 2wd, 4wd hi/low, hubs locked or not. I changed the vacuum pump, no leaks, changed the IWE solenoid, pulled out both locking mechanisms, tightened crossmember, checked everything from the hours of research I did on the internet. I cannot find the problem. I don't know what else to check. Front axles free spin and lock when they are supposed to. I'm at the end...
Ford Super Duty (1999-2016) :: 2000 - When Turning Hard Left Only Makes Grinding Noise?
First off my trucks a 2000 v10 f250 with four-wheel drive and 2 wheel abs with about 230000 miles on it.
I Recently replaced my unit bearing on my drivers side because I thought it was the cause of a grinding that only happens on hard left turns but I wasnt the cause it was going bad causing play in the half shaft. I didnt seem to notice and wear on the shaft from bad needle bearings but I have to take it all apart again to be sure. Was just wondering what else could be the cause of this noise. I plan to pull the axel shaft and change all the seals.
Ford Super Duty (1999-2016) :: 2003 F350 Pulling Hard Left At Low Speed When Braking
I have an 03 F350 4x4 dually. Was pulling hard left at low speed when braking (front). Replaced pads, calipers, rotors, hoses and tires. Still the same problem. You can feel the abs activate right before it almost locks up the left front brake (basically will pull the steering wheel out of my hand). BTW the abs light does not come on.
View 2 RepliesFord Super Duty (1999-2016) :: Left Turn Signal On All The Time
2012 F250 left turn signal on all the time no right turn signal.
View 2 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Hard To Start
My '01 f250 7.3 has gotten hard to start. It seems to maybe be due to cooler weather, but not always. I have been told that there is some sort of valve in the fuel tank that could possibly cause this when the fuel gets around a 1/4 tank or so. But, it's doing it at any fuel level. But it doesn't do it all the time. I do notice it more in cooler weather. Anyway, when I try to crank it, I'll let the "wait to start" light go off and then wait a bit more. I'll turn it over and it almost as if the batteries are weak.
I'll stop and give it a few seconds and turn it again and it will normally start. But sometimes I'll do this 5 or 6 times and it will finally fire. But the more I have to try, it's like fuel builds in the cylinders and it smoke like a coal train for a minute or so. Almost like gas motor that has been flooded. But the smoke burns off and it runs like a top. I was thinking the batteries may be weak , but sometimes the starter will spin the motor with no trouble at all. I'm at a loss. Is it possible for fuel to drain from the system causing it to have to reprime itself? Here lately the smoking has me concerned even though it clears up.
Ford Super Duty (1999-2016) :: 2011 F250 - Really Hard To Steer
I own a 2011 f-250 superduty, and have been having a problem with the steering, it goes from normal to lost of assist. Real hard to steer and dangerous. Then it will go away for a month, then start again. Some one on this site told me to flush the system which I did and it was fine for a month. A friend at a local ford dealer told me they had contamination in the system and I had to replace pump, reservoir, and flush system again....
View 10 RepliesFord Super Duty (1999-2016) :: 1997 F250 - Hard Shifting?
I have a 1997 f-250 heavy duty with the 7.3 I have been having problems with very aggressive and hard shifting. While it is acting up the overdrive light on the shifter blinks. This problem goes away and it might be good for a month or so, But it always comes back. I have had it to a professional trans tech, He replaced a part on the side of the tranny. I thought it was fixed, But now it is acting up again.
View 4 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Steering Binding Turning Left
I bought a 2004 F250 Crew Cab LB 4x4 with the 5.4 Motor and when I turn left it has some Tight Spots and I can't figure out why, I checked the Drive axles to make sure the locking hubs were unlocked and they spun freely, I Also have a lot of play in the steering wheel, Could this all be Related to the Steering Box? What else should I check for ?
View 3 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Two Pin Electrical Harness On Left Inner Fender
I recently had need of replacing my left exhaust manifold on a 2000 F250 4 x 4. I removed plastic inner fender well. Now I have a two pin harness with both white wires. One is white with red stripe, the other is white with black stripe. The harness is round with a locking square on one side. The harness is located about 10" from bottom of inner left plastic fender panel. It has 2 mounting pegs. Where the heck does this connect?
View 13 RepliesFord Super Duty (1999-2016) :: F250 Pulls To The Left When Driving / Front Outer Tie Rod Bad
1999 F250 SD 4x4 7.3 PSD ... My truck has 198K miles on it. It pulls to the left as I drive it. So I took it to a shop to have the alignment checked. They told me that the front outer tie rod was bad and needed to be replaced. And of course they said they needed to put in a set of caster camber bushings to do the alignment. They quoted $400 to change the tie rod out. I said I would do that. They gave me the print out from the alignment but reading it the only thing that was out was the toe. Left tire was toe out and the right tire was toe in, which to me would cause it to pull to the left.
I got under the truck and the steering link, piece that goes from steering box to right side/tie rod, is not tight...I can move it up and down and it clunks when I roll it up. I have a clunking noise when I drive it and go over bumps also. Could this be the clunking noise? Also, if I replaced the ends of the steering link, that would tighten up but possibly push the steering back to the right some to straighten out the tires? I have read alot of threads talking about the clunking being tied to the sway bar bushings being bad but the clunking I get by rolling the steering link up and down sounds alot like the noise I am hearing.
Also, when looking at the axles where they go into the knuckle, there is a loose plastic ring on both sides. Is this part of the dust shield or an oil seal?
Ford Super Duty (1999-2016) :: F250 - Wear On The Inside Of Left Front Tire
I have a 99 F-250 extended cab superduty 4 wd with the 7.3. I also plow during the winter. Recently I've noticed wear on the inside of the left front tire. Brought it to a tire shop and had them check the front end and alignment. They told me that the specs were "within" tolerances" for my truck. I'm stumped as to why the abnormal wear if everything is supposedly good with the alignment.
View 5 RepliesFord Super Duty (1999-2016) :: F250 - Steering Wheel Canted Left While Turning Right?
I had some steering issues with my truck so took it for an evaluation at pep boys. They recommended a new steering gear box and tie rod that hooks to the pitman arm so I had them replace them. Steering was improved but now the wheel is canted to the left or right depending on when I make a turn. When I make a left turn, the wheel is canted about 10 o'clock. When I make a right turn, it's canted about 1 o'clock.
I looked under and had my brother turn the wheel and didn't really notice any thing loose. I lifted the front and noticed the left wheel bearings need to be replaced. I also noticed the shocks were shot and replaced them but it didn't make a difference in the crooked wheel.
Do you think it's the wheel bearing that can cause this? How about the ball joints? The truck has 407k miles and I bought it a month ago. Previous owner said he never replaced any steering components. Should I just replace all steering components with the Moog kit? I'd like to hold off on the $600+ kit for now as I just bought a a boat and the boat needs some stuff. I hope to find that one thing (hopefully not more) that's loose.
Ford Super Duty (1999-2016) :: 2008 F250 - Left Rear Brakes Hanging Up
Took truck out for a ride and stopped for gas. I smelled Brakes and upon inspection found the left rear brake pads were not releasing. Any take on what could be holding it? 2008 F-250.
View 10 RepliesFord Super Duty (1999-2016) :: Left Front Caliper Is Not Squeezing Hard Enough To Stop The Truck Evenly
Having a problem with calipers again/still seems like always. Replaced all calipers twice in 86K miles on a 2000 f250 crew 4x4 because of stuck calipers. Replaced brake hoses and all hard lines in the rear about 2 years ago. My problem now is the left front caliper is not squeezing hard enough to stop the truck evenly. (pulls to the right) The rotor had some rust from sitting and after driving a for a while the rust is not completely gone as you would expect. Replaced caliper bled a couple of times. Caliper looks to be getting pressure enough to bleed and can see it move when brakes applied when engine not running. I don't have experience with Proportioning Valves but do you think that is the problem and how do I fix it?
View 8 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Transmission Shifting Hard
I have a 2002 ford f250 with the 7.3l diesel. I recently installed a ts performance chip. On my pcm. And after i first tried all the different stages I didn't like how my transmission was shifting hard. So I contacted the manufacturer and he told me they could reprogram the chip for smoother shifting. So I removed the pcm and removed the chip. But when I went to reinstall the pcm I bent one of the pins on the pcm some how.
So I took it back out and straightened the pin with pliers . i reinstalled it back in the truck. Only to find when I reattached the battery cable I have no power to anything ignition ,horn, lights,Cigarette lighter etc. So my question is if the pcm is bad, or not contacting properly due to the pin being messed up. would that have anything to do with the lights and horn and all that? I suspect its the gem bsm or Vsm. Whichever one my truck has. But really not sure because everything worked fine just 20 min b4.
Ford Super Duty (1999-2016) :: 2006 F250 - Hard Shuddering When Braking
When braking the truck shakes terribly, enough to toss a drink out of the cup holder almost. Sometimes there is a slight feeling in the peddle but not always. The shudder feels like it is timed with each revolution of the wheels.
It developed from a perfectly stopping truck over the course of maybe a month. I don't drive the truck that much either.
Things I have checked:
1, all u-joints, they all look and feel good, no play or slop in them
2, air pressure in all tires, even rotated them, no effect
3, brakes-front and back all looked good but I went ahead and replaced front pads and rotors, cleaned caliper pins, zero effect.
4, shudder exists whether in gear and slowing or in neutral, 2wd and 4wd
What the heck else is there to check? My first thought was, front brakes/warped rotors, but after pulling them apart there was so much life left on the rotors and pads and replacing all that with new did nothing! Could bad back brakes cause this much of a shudder? They look fine as well.
Ford Super Duty (1999-2016) :: 2000 F250 - Hard To Drive Under 40 MPH In 3rd Gear
I recently purchased a 00 F250 psd 4x4. Other than doing all of the fixes it needs to make it ride better I have been questioning the trucks "get up and go" and the EXTREMELY sensitive skinny pedal. Truck seems to pull very hard and puts out some black smoke under hard throttle but nothing like the really tuned trucks I have seen. But the skinny is so sensitive its hard to drive under 40mph in 3rd and once it gets up to 55 or so its real sharp getting on and off the throttle. Trans shifts great, TC locks and unlocks, truck runs awesome IMO but just a bit harsh. Is there a way to find out if it was tuned prior to me buying it other than inspecting for a chip, or is this the way they are and I just have to get used to it more...?
View 9 Replies