Ford :: 2007 - Can't Get Into Gear - Shifter Won't Budge
I drive a 2007 Ford Focus (manual trans), and it's been acting funny lately.
Here's the problem: Lately, when I start the car and try to put it into gear (either 1st OR R,) the shifter won't budge. While the engine is off, I can put it in gear just fine. After I wait for a little, turn the car off and on again, etc, I can get the shifter into gear if I really push it HARD. (I know I probably shouldn't do this, but... I was terribly late and desperate!) Okay, so I get the car into first and manage to pull out of my parking spot without having to reverse. When I go to get into second gear, I've still gotta push the shifter REALLY hard (again, bad!! I know!) but maybe a little easier. Where I live, it's stop-sign city, so I have to stop and go a lot, and within a few minutes of this (maybe 3 or 4 cycles of N, 1, 2, maybe 3, N) I can shift smoothly again and the car feels totally normal.
The strange thing is, this happens sporadically, and I can't seem to see any external factors that correlate with the problem, except that it seems to be worse when the car's been sitting for a couple days. Sometimes the car shifts just fine, and sometimes it won't get into gear at all. In general, the car's in pretty good shape: no accidents, scheduled maintenance, etc. I guess the only caveat is that a couple years ago, TWO people learned to drive stick in this vehicle, so maybe the transmission has taken some abuse.
Ford Ranger / B-Series :: 2003 - Truck Wouldn't Start Again After Parked
My 03 Ranger 4.0L has become a mystery that has baffled every one I know. Everything was fine and I ran home to something from my house was in there maybe 10 minutes came out and the truck wouldn't start. it doesn't even crank over. out of the clear blue. I had a friend who works for a garage check it and he thinks timing chain. Since then I have been told it wouldn't just fall off sitting there with no indication at all there was a problem.
Thought maybe PATS system. Its in order. Put in on a computer from auto-zone and it shows a check engine light but the reading is there is no codes in the computer on file. I am at a loss. Its been months and I really cant afford to take it to a garage right now. Its the strangest thing ever no crank, no stalling just nothing I hit the switch it lights up like its ready to start and nada.
Ford Ranger / B-Series :: Cruise Control Stuck On And Wouldn't Release
So I'm motoring along a country road with the cruise set at 50 mph and the truck starts to increase speed.
Tap the brake - nothing happens. I'm up to 65 mph! Knock it into neutral and it revs to around 3,500 rpms and then it unsticks.
What in the world is going on with that? After thinking on it, a few miles farther on and I set the cruise again.
It began immediately picking up speed. I hit the brake and nothing happened. Then I hit the off button and nothing happened.
So again I bumped it up into neutral and it did the same thing - revved for a moment and then kicked off.
The dealership where I get my service done can't get to it for several days. So I'm checking in the meanwhile to see possibilities to identify a cause.
Ford Ranger / B-Series :: 1996 - Truck Suddenly Shut Off And Wouldn't Start
I have a ford ranger 1996 4 cylinder. The truck was driving fine then all of the sudden it shut off and wouldn't start... I checked spark and that is fine also changed fuel pump and made no difference. We also sprayed lighter fluid and that did nothing. It sounds like it wants to start but wont.
View 10 RepliesFord Ranger / B-Series :: 2.3L Mazda B2300 Died And Wouldn't Start Back Up
I am working on a 96 Mazda b2300 auto 2wd for a friend. His son was driving it when a loud noise, it died and wouldn't start back up. He had it towed to my house, I started to tear into to it and found it slipped the timing belt. So a rebuilt head, gaskets, timing belt, fuel injectors, water pump, thermostat, plugs, and fluids; tried to start it and nothing. Started troubleshooting and found the primary coil pack was out of spec, replaced and still nothing.
Changed out the CKPS still nothing? I have spark, I have fuel, I'm going to check compression tomorrow but the way the cylinders and pistons looked I don't think that is the issue but I going to check anyway, rechecked the timing marks they all lined up. Checked the fuel inertia switch not tripped. Could the PCM, or ICM cause a no start, and still be able to get spark and fuel?
Golf IV / Jetta IV :: Shifter Got Stuck And Won't Budge Out Of 5th Gear?
I'm having an issue with my clutch and I'm really in a hole. Two days ago I was driving my car and everything was fine. Later in the day the shifter got stuck and would not budge out of 5th gear. Eventually it popped out. Driving like normal again and then yesterday I was on my way home from work and all hell broke loose. I was a mile away from my house and the car would not shift into any gear without a fight.
I also at this time lost my clutch pedal. It went really soft but did come back up.. it would not engage however. Limped it the rest of the way home and took a look at it. What I came across was a full brake/clutch reservoir, no leaks around the slave, and I didn't see any leaks around the master. I will say that after the car sat for about 10 mins the pedal felt normal again but quickly went soft after a few pumps.
2.0 AEG 5spd. Trans code DZQ if any of that would be relevant..
Ford Ranger / B-Series :: 1983 - TK5 Shifter Assembly Replacement?
My 1983 Ranger is in the shop. I'm being told that I need to replace the shifter assembly. I understand that this is a Mazda part, from a TK5 transmission. These parts are interchangable between bronco ii's of the same era.
View 1 RepliesFord Ranger / B-Series :: Truck Started On Its Own / Wouldn't Shut Off And Starter Engaged In Park
So I turned off my truck the other day, got out, and it started again on its own. Confused, I looked in my hand to see my key. I got back in, and tapped the brake thinking the command start had engaged, even though I did not have the remote with me. It continued to run. So I put the key back in the ignition, turned it to ON and back OFF. It still ran. I had to run inside for a half a minute so I left it running.
Came back and drove away with no issues. When I stopped again about 2 minutes later and shifted to PARK, the starter engaged making it's terrible 'hey stupid, I'm already running' sound. I tried shutting it OFF quickly but it still ran and made it's skinning crawling noise. So I quickly shifted back to DRIVE. All the gears worked fine but PARK and NEUTRAL had the starter engaging. I also could not shut the truck off from DRIVE as the key would not turn.
I drove over to a local garage and called them from the truck as I was effectively trapped in the truck with my foot on the brake, unable to shift to PARK or turn it OFF. No supporting staff. So I drove back to work where I had a co-worker remove the battery cable at which point I was able to shift to PARK and turn OFF the truck. I let it sit like that for about 10 minutes and haven't had a problem since.
What happened?? And for the record I can put gas in the tank and changed my own oil, but that is the extent of my vehicle knowledge.
Ford Ranger / B-Series :: 1985 - Shifter Really Loose / Stuck In Reverse
1985 ranger 2.3L TK5 tranny. Shifter was really loose and the tranny finally got stuck in reverse. I have opened up the bottom cover, but am not sure where to move the shift forks to get it back to neutral. I bought a new shifter, but I need to get the tranny back to neutral before I can install it.
View 2 RepliesFord Ranger / B-Series :: Column Shifter Too Hard To Shift Through Gears?
I've been having problems with my column shifter ever since I installed a Pioneer shift cable probably about 3 years now. I was told and also thought that the cable would loosen up after awhile but it never has. I had some put it on and I watched him do it. He seemed to have some trouble because it took him a long time under the dash. It shifts so stiff that over a period of about 2 years it finally broke the end of the shift tube one night. Luckily I was able to fix it the next day by getting a spare without missing any down time. It was still just as stiff with the other shift tube. It finally broke the plastic on my shifter tonight, not necessarily whatever is causing it but because it takes so much effort to shift into Park, Reverse or Drive.
I think the plastic may have cracked over time. Luckily I had another one at home along with another shift tube. I didn't replace the shift tube this time but I did remove the caps and smear some grease on the bushings to see if it would make it turn. I looked further down at the end cap that broke last time and sure enough one of the bolts was backed almost all the way out. I retightened it tonight too. That's what happened when the bottom broke last time. One of those bolts backed out and it cracked the housing. It works now but if you go all the way to 1st to get back to anywhere it really takes a tremendous amount of effort to get it to shift. Something is not right and I cannot pinpoint it. I know they offer brand new shift tubes but I'm not sure if that's the problem.
Ford Ranger / B-Series :: 2001 - Copper Cable Doesn't Move When The Shifter Does
After taking apart my instrument panel to change the bulbs, I went to reconnect everything, but now the gear shift indicator isn't working. I can change gears fine, and everything else on the instrument panel works just fine.
The copper cable that connects to the shifter doesn't move when the shifter does. Is there a way to fix this problem, or do I need to find a replacement cable?
Ford Ranger / B-Series :: 2000 - No Start - Wiggle The Shifter To Start?
2000 ranger auto 3.0 wife said that she had problems starting the truck
She had wiggle the shifter to get it to start. Have not looked at it yet but i am think the newtrl safety Switch.
Ford Aerostar :: Revving High For 65 - 70 MPH / Shifter Wouldn't Go Into Reverse
I drove our 95 3.0l aero to work today, I was going to a job 45 miles away. It sounded like it was revving awfully high for 65-70mph, but the gear selecter said od, so I figured I was just crazy. Got to the job and tried to back up and the shifter wouldn't go into reverse. Parked for the day after realizing the shifter would go N and down, but not into rev or park. Apparently it was revving high, as the gear indicator was now off and I was no doubt in drive, driving to work. I got it home, then had to drop my daughter at work, by staying in OD.
Then on the way home the van just DIES while going 35+- mph. Won't restart, smelled gas after many many attempts to start. Towed home. NO spark. I have 12+ volts at+coil. I tried my ignition module and a new one, neither sparked at the coil wire. I bought a new coil, then checked resistance at + &-, and - and coil output post. Basically same resistance new & old coil. Did my hall effects or cam, or crank sensor just go out or? Why both problems same day? I thought if it was the coil or ignition module, maybe it got too warm on drive revving high. Does a 95 3.0 coil get triggered by the distrib haal effects or does the crank sensor do it?
I can easily see one of those being bad as they are original, with 334,000+ miles. All the tune up, coil, wires, plugs, ign module, cap, rotor, were replaced 55,000 miles ago. ALSO does this distrib have a TFI module on it? My book says to pull the distrib and remove it, like my 5.0l Mustang, but I don't see one, I think thats the ignition module on the pass. inner fender. I'd like to see if I can get 400,000 miles out of it.
Ford Ranger / B-Series :: Gear Shifter Does Not Go Into 1st Gear But Changes To Other Ones
I bought a 96 Ford Ranger XLT Supercab 4.0 on the 21st and the gear shifter doesn't go into 1st gear but changes to the other ones(see pic below) and was wondering if it's a easy fix.
Also I have a oil drip(at least it looks like oil to me) and I can't figure out where it's coming from because it's a small drip and the oil dipstick and tranny dipstick both show full and I can't figure out where the drip is coming from and I only noticed a dip on a metallic tank but don't know what that is either but check out the pic below to see the drip I circled.
Ford Ranger / B-Series :: Hesitation When First Pulling Out From A Stop
That's the best way I can describe part my latest problem. If I'm stopped at a light, a lot of the time it almost feels like it wants to stall when I first pull out. Then, it seems like it is shifting funny at certain speeds like the transmission can't decide what gear it wants to be in. Tends to do that about mid acceleration (don't have an rpm gauge to look at). At idle it seems to run fine. BTW, engine also runs rough with the ac on.
View 12 RepliesFord Ranger / B-Series :: Truck Pulsating When Coming To A Stop
My truck is pulsating when I am coming to a stop, a lot of you all said replace the rotors to which i did and new brakes, shocks. Today I went to get my truck all four wheel alignment done to my truck.. something is not right..
I got my driver tire facing straight, look at the left.. I went back to the alignment shop showed them that, they put it back up there, they called me over and pointed out the machine they use say, it is aligned.. So what is the problem you figure?
To update all I've done to the truck in regards to front end..
rack and pinion
upper control arm
upper lower ball joints
stabilizer inks
rotors (front)
brakes
shocks
When I straighten my left wheel, the right does not look right..
Ford Ranger / B-Series :: Long Time To Go Into Any Gear When At A Complete Stop
When ever i am at a complete stop, i have to hold down the clutch pedal for about 4 seconds before it will go into any gear. If i'm in motion it shifts flawlessly through all gears. But if i stop and put it into neutral and let off the clutch, the next time i push it down it will take about 4 seconds to slide in any gear including reverse. I just bought the truck a few days ago so i don't know its history but everything seems well maintained. What this is and if it will cause major issues down the line?
1995 Ranger XLT 2.3L SOHC 2WD 5spd 169,000 miles...
Ford Ranger / B-Series :: 1996 - One Of Tire Locks Up When Coming To A Stop
I have the problem that my 1996 ranger 4x4 has a break problem. When it comes to a stop it feels like one of the tires locks up, feel wired. Ihad the problem before i changed the front breakpads and it still continues. Air in the lines? ABS module?
View 6 RepliesFord Ranger / B-Series :: ABS Engaging When Slow Down To A Stop While Turning Left
I noticed that my ABS was engaging when I would slow down to a stop while turning left. I pulled the fuse for the ABS just to make sure that's what was causing the pulsating brake, and it was. Anyway, if it's an ABS sensor problem, would it be the front passenger side sensor if it's only happening when I turn left? Is there a way to test this. Would a scanner detect it? It hasn't been throwing a code or anything. Just the ABS engaging while braking and turning to the left when it shouldn't be.
View 6 Replies