Ford Ranger / B-Series :: 1983 2.3L - No Spark When First Turn The Key
Truck has no spark except when you first turn key on it sparks or right when you let off from cranking it will give one spark. You can be cranking it and nothing and when you let off it kinda acts like it wants to start for a millisecond.
View 11 RepliesFord Ranger / B-Series :: 1983 With YFA - Inlet Gasket Stuck
I have a 1983 ranger with a YFA. I recently took it apart and in the process of the rebuild I noticed the metal gasket was still in the spot where the needle pin goes. It has adhered to the carb. Any way to get it un-stuck? Also, there is a module, and the gasket comes in the rebuild kit so I know it belongs, the part number begins with 2I3 but the rest came off with the dirt. What is it for and would it hurt anything if it wasn't plugged in? It hasn't been since I bought it.
View 2 RepliesFord Ranger / B-Series :: 1983 - Poor Fuel Mileage?
I recently bought a 1983 Ford Ranger Diesel pickup truck (2.2L Mazda engine, manual transmission). The dealer said to expect a little above 30 mpg on fuel mileage but the two fill-ups I've done show an average fuel mileage of 22 mpg. About half of these are highway miles.
I thought diesels are supposed to have good mileage. Is this typical for my year and model truck? Is there any way to increase the mileage? I just replaced the air and fuel filters and also changed the oil and oil filters.
Ford Ranger / B-Series :: 1983 - Vibrates Around 35 MPH - Shaft Bearing Broke - Replace Trans?
I noticed a strange vibration in the 83 Ranger I own, it has the 2.3 and a 4 speed. When getting up to speed around 35MPH it would start vibrating, and the speedometer needle would bounce around and read slower than it was actually moving. This would start in 3rd gear, and continue thru 4th unless I let off the gas while it was in gear, then it stopped and worked normally. I put a grease seal in the tail section when I first got the truck, and when I pulled the driveshaft again today the seal was mangled and bent, plus there are metal particles around the main shaft where the seal goes. I figure the tail shaft bearing is shot, and I also found damage to the yolk with the U-joint, the shaft has a worn spot about 1/3rd the way around.
View 2 RepliesFord Ranger / B-Series :: Missing The Nut On Top Side Of Front Stabilizer Bar Link Bolt Assembly
Today while driving I noticed a knocking when turning right or going over bumps in the road. I finally got to look under the truck and noticed that I'm missing the nut on the top side of the front stabilizer bar link bolt assembly on the passenger side.
It's a '99 Ranger XLT 4x4. Is this unsafe to drive? Is there a bushing on the top?
Ford Ranger / B-Series :: 1985 - Shifter Really Loose / Stuck In Reverse
1985 ranger 2.3L TK5 tranny. Shifter was really loose and the tranny finally got stuck in reverse. I have opened up the bottom cover, but am not sure where to move the shift forks to get it back to neutral. I bought a new shifter, but I need to get the tranny back to neutral before I can install it.
View 2 RepliesFord Ranger / B-Series :: When Go From 4th To 5th Shifter Wouldn't Budge While Upshifting From A Stop
I have an 89 Ranger, 5 speed, 2wd, M50D transmission. On the way home tonight I was upshifting from a stop and when I went to go from 4th to 5th the shifter wouldn't budge. Luckily I was on a back road so I pulled off the road and tried all sorts of things (rolling truck while stopped, etc) and the shifter just will not budge.
Now here is the thing. I had my fiancé with me and no tools so I really couldn't do any diagnosing. However, 6 months ago I replaced the clutch, pressure plate, throwout bearing, slave cylinder, and pilot bearing. While I had the transmission out of the truck I changed the fluid, siliconed around the rubber plugs, and put a shift bushing kit in. The bushing kit is the bushings around the shift ball with new wave washers and new pins that insert into the ball.
It is obviously not related to the clutch as it engages/disengages properly. When this happened, there were no noises of any kind when I shifted from 3rd to 4th. It just will not come out of 4th. I am going to pull the shifter out tomorrow and have a look. Do you think one of the new pins that I drove in to hold the shift ball broke or fell out or something and if so would it cause this problem?
Ford Ranger / B-Series :: Column Shifter Too Hard To Shift Through Gears?
I've been having problems with my column shifter ever since I installed a Pioneer shift cable probably about 3 years now. I was told and also thought that the cable would loosen up after awhile but it never has. I had some put it on and I watched him do it. He seemed to have some trouble because it took him a long time under the dash. It shifts so stiff that over a period of about 2 years it finally broke the end of the shift tube one night. Luckily I was able to fix it the next day by getting a spare without missing any down time. It was still just as stiff with the other shift tube. It finally broke the plastic on my shifter tonight, not necessarily whatever is causing it but because it takes so much effort to shift into Park, Reverse or Drive.
I think the plastic may have cracked over time. Luckily I had another one at home along with another shift tube. I didn't replace the shift tube this time but I did remove the caps and smear some grease on the bushings to see if it would make it turn. I looked further down at the end cap that broke last time and sure enough one of the bolts was backed almost all the way out. I retightened it tonight too. That's what happened when the bottom broke last time. One of those bolts backed out and it cracked the housing. It works now but if you go all the way to 1st to get back to anywhere it really takes a tremendous amount of effort to get it to shift. Something is not right and I cannot pinpoint it. I know they offer brand new shift tubes but I'm not sure if that's the problem.
Ford Ranger / B-Series :: 2001 - Copper Cable Doesn't Move When The Shifter Does
After taking apart my instrument panel to change the bulbs, I went to reconnect everything, but now the gear shift indicator isn't working. I can change gears fine, and everything else on the instrument panel works just fine.
The copper cable that connects to the shifter doesn't move when the shifter does. Is there a way to fix this problem, or do I need to find a replacement cable?
Celica :: 1983 - Shifter Sticks While Shifting Into 3rd Gear
i have an 83 gt celica and i am have trouble getting the gear shift to go into 3rd gear. I can do it if i shift slowly, but doing this fast risks shifting into 1st or getting jammed between 1st and 3rd.
i have attached a link to a diagram of the shifter parts and this contains more info on the car and engine type if needed. My question is what exactly do i need to replace to make it easier to shift?I have removed the boot and the gasket just to look inside and see if something looks bent, but I have not taken out the retainer or the plate below, but i am thinking that is the piece i need to replace.
Ford Ranger / B-Series :: 2000 - No Start - Wiggle The Shifter To Start?
2000 ranger auto 3.0 wife said that she had problems starting the truck
She had wiggle the shifter to get it to start. Have not looked at it yet but i am think the newtrl safety Switch.
Ford Ranger / B-Series :: 2.8L V6 Valve Stem Replacement?
I have a 1984 ranger with the 2.8L and I am doing the valve stem oil seals.
I have instructions from the ranger station. And I have access to mitchell1 and chilton online.
Also I read somewhere about better settings to use for valve lash? The truck has about 80,000 miles on it.
Ford Ranger / B-Series :: Gear Shifter Does Not Go Into 1st Gear But Changes To Other Ones
I bought a 96 Ford Ranger XLT Supercab 4.0 on the 21st and the gear shifter doesn't go into 1st gear but changes to the other ones(see pic below) and was wondering if it's a easy fix.
Also I have a oil drip(at least it looks like oil to me) and I can't figure out where it's coming from because it's a small drip and the oil dipstick and tranny dipstick both show full and I can't figure out where the drip is coming from and I only noticed a dip on a metallic tank but don't know what that is either but check out the pic below to see the drip I circled.
Ford Ranger / B-Series :: Fuel Filter Removal / Replacement
I know where the filter is, i know how to bleed off the pressure. Im wondering if those clips are easy to slide off to remove the filter from the lines?
View 7 RepliesFord Ranger / B-Series :: 1999 - Clutch Slipping - Replacement?
My clutch is weak and slips sometimes and I need to replace it. ,I have replaced the clutch disc in other trucks but never a Ranger.
1999 3.0, 5 speed stick, Extended cab....
Ford Ranger / B-Series :: 1996 - Power Steering Replacement
I'm in the middle of replacing my pump. With the new pump are a plastic washer and a small rubber o-ring but no instruction where they are supposed to go. They didn't know at auto zone and I haven't heard them mentioned on any youtube video. I found a crushed torn up washer similar to the plastic one in my catch pan. Maybe it is supposed to go in around the high pressure hose connection.
View 6 RepliesFord Ranger / B-Series :: 2003 - Replacement Of Outside Mirror Glass?
Is it possible to replace just the glass on the outside mirrors on a 2003 Ranger?
If so, how is it done?
Ford Ranger / B-Series :: 1999 - Rear Main Replacement?
I'm an experienced home mech, not really worried about doing the job. Just curious if there is any pitfalls I need to know about, or a trick/tip that may make the job easier?
View 8 RepliesFord Ranger / B-Series :: 2011 - OEM Radio Unit Replacement
I have a 2011 Ranger. It came with Sirius radio which works with the AUX button on the head unit. This setup is not what I am use to. Anyway I want to replace the OEM unit with an aftermarket. My question is will this AUX connection effect an aftermarket radio connection?
View 11 Replies