Ford Super Duty (1999-2016) :: Torque For Differential Cover Bolts
Torque on the differential cover bolts, 2016 F250?
View 6 RepliesFord Ranger / B-Series :: Top 2 Bolts Removal Of Transmission?
How in the heck do you get the top 2 bolts off of the transmission housing? They seem to be positioned in such a way that they are impossible to remove.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Injector Installation - Torque Hold Down Bolts
I have been reading here about alternate methods to torquing the hold down bolts for the injectors. This winter I replaced my old stock split shots with new alliant single shots. I installed the injectors into a cold engine and torqued the hold down bolts to 10 ft lbs. I did not ever go back and re-tighten.
Is it suggested to go in and re-tighten the injector hold down bolts to 10 ft-lbs after the engine has been heated up and cooled down? What are some symptoms of a loose injector? I am imagining premature wear on the injector cups, low compression and maybe some mixing of oil into the combustion chamber.
Did just throw the injectors in and go back later to retorque only to find they were all fine or were some loose?
Ford 7.3L Power Stroke (1999-2003) :: Water Pump Lower Elbow Bolts Torque Specs
I read 18lbs for the water pump but it took a cheater bar (perhaps due to corrosion) to get the water pump lower elbow bolts off.
On reinstallation, what should the lower elbow bolts be torqued to? Checked the sticky (Ziggy's Torque Specs) but didn't see the specs for this item.
Ford 7.3L Power Stroke (1999-2003) :: Injector Hold Down Bolts Not Torque Down To Spec - Hard Starting?
I wanted to know what happens when the injector hold down bolts are not torqued down to spec, what problems would arise and could it be a reason for somewhat hard starting?
View 1 RepliesFord Ranger / B-Series :: Engine Build For More Power And Torque?
I am looking for any info on what to use for engine build for more power and torque in my race car.
View 14 RepliesFord Ranger / B-Series :: Blown Head Gasket?
I have read all I could find on replacing a blown head gasket and and after absorbing everything that TigerDan posted on here, I dove in and began. After disassembling all the topside junk I finally got the intake manifold loose and got down to the head. I began undoing the head bolts and found two broken bolts. The head won't budge so I am calling in a cherrypicker. I don't know what kind of mess I'll find when the head comes off. I assume the head will be warped or the block may be damaged.
View 6 RepliesFord F-150 (2004-2008) :: Torque Value For The Trans Pan Bolts?
I am finally getting around to changing the trans fluid on my 05 f150 5.4 4wd xlt auto, what is the torque value for the trans pan bolts.
View 1 RepliesFord Ranger / B-Series :: 1991 - Bad Head Gasket - Leaking And Coolant In Oil
I have a 91 Ranger V6 4WD with 150K that has been sitting for 7 years. The last time I drove it (7 years ago) to a mechanic, who diagnosed it with a bad head gasket - leaking coolant and coolant in the oil.
What am I looking at as far as a project: besides redoing the head gasket, what else will I most likely need to do given that its been sitting 7 years?
Ford Ranger / B-Series :: 1995 - No Spark / Leaking Head Gasket
My 95 Ranger has been a good truck in the 6 years I've owned it. I had to pull the heads to replace a leaking head gasket and wound up having the heads rebuilt due to weak valve springs and worn valves. I replaced the gaskets, installed the heads, get it all back together.....won't start. Fuel pressure is good. Found that there is no spark. While putting the crankshaft position sensor connector back on I noticed it didn't look too good. I replaced the connector and that's all I did and no spark. Long story short, after a lot of research, the coil pack, cps and coolant temp sensor were replaced and still no spark.
Everything has the proper voltage to it. After a little more research I found a post with the same basic issue. His issue wound up being the ecm. So I removed the ecm....it's a used one from a salvage yard. I've owned the truck 6 years so I have no idea when the ecm was replaced. It showed up today and will get installed when I get home from work. I also ran across posts about the camshaft sunchronizer and they should be replaced at about 80K miles. Since the truck has 289K I'll replace it. Still no spark. I'm hoping it's the ecm.
Ford - Explorer :: 2004 - Torque Value For Water Outlet Bolts?
What is the torque value for the 2 bolts on the upper radiator hose water outlet on an '04 4.6L?
View 1 RepliesFord Ranger / B-Series :: 1994 - Coolant Loss / Head Gasket Leaking
I am working on my buddy's 1994 Ranger with a 2.3L I4 that has been going thru a large amount of engine coolant. The trucks has approximately 180,000 miles on it. When I had it parked on concrete I have not seen any signs of coolant on the concrete or any signs of coolant leaking. The next place I checked was inside the cab to see if there was any coolant from the heater core and there was not. The water pump has been replaced a couple of years back. I replaced the spark plugs today and did not see anything on the plugs that I would have thought were signs of coolant in the combustion chambers.
With that being said I have not worked on a vehicle with a leaking head gasket before. Would there be any visible signs on the sparks plugs? If so what would I be looking for? When standing in front of the vehicle with the engine running there is a slight smell of antifreeze being "vaporized". Are there any noted issues with this engine that would cause this? Are there any other things I should check? Could it be a leaking head gasket causing this? If so how can I check for that?
Ford Ranger / B-Series :: 1994 - Blew Fusible Link To Alternator After Rebuilt Head?
I bought a 94 2.3 did a head job bought a rebuilt head and got it all back together hooked up the battery and blew the fusible link to the alternator. Did I screw something up? I have been rebuilding engines for a long time and never had this happen. Tested the alternator and the O'Reilly guy said that the Voltage regulator was shot putting out 17 amps and that is why the fusable link blew. I don't think that's right because the engine was not running I just hooked up the battery, and no I did not switch the pos and neg. I'm dumb but not that dumb. Any guesses?
View 1 RepliesFord Ranger / B-Series :: 2000 V6 - Blown Head Gasket / Radiator Fluid Goes Straight To The Oil Pan
I have a 2000 Ranger, V6 4L, and I believe my head gasket is blown, my radiator fluid goes straight to the oil pan. It has probably been leaking for a while, I did not realize it was leaking internally, I had been adding coolant for a few months but thought it was my radiator leaking because it had a crack in the housing, so I had that changed, but then a few weeks after that It gave out. I drained, and flushed the engine twice, and just parked it. My question is, should I just have the head gasket changed, or does it need a new engine because it had been leaking for a while and not sure what kind of damage it has done internally.
View 3 RepliesFord Ranger / B-Series :: 1993 3.0 - Head Gasket Failure / Blowing White Smoke And Using Coolant
Well I finally went and bought another Ranger. Pretty red 5spd 4WD long bed. I knew it didn't run when I got it (crazy leaky fuel line...stupid squirrels), and the owner was pretty sure it had a head gasket failure. He claimed it was blowing white smoke and using coolant. I hadn't been able to get it to run to verify that, but I can't see why he would lie about that.
I finally got the fuel line fixed today (FYI, don't waste your time or money buying those Dorman OEM connector patch kits at Advanced Auto). While we were cranking the truck, I noticed gas escaping the degas bottle the radiator was pressurized before the thermostat should be open. That to me says blown head gasket (crossing fingers it isn't a cracked head) for sure. I tried to get a picture of the dipstick, but in the light it definitely looks like peanut butter. I just wanted to make sure before the massive ordeal of pulling heads/top end work that will follow
Anyway, plan is to fix her up and get her back on the road! Some picture enjoyment .......
Ford F-150 (2009-2014) :: 2012 - Mounting New Shocks - Torque Specs For Upper And Lower Bolts?
Mounting the shock with the boot up or down? I know it doesn't matter according to Bilstein but one way has to be better than the other.
Second. What are the torque specs for the upper and lower bolts? I know the lower front is around 350lbs but haven't found anything for the rest. found out the rear bolts are torqued to 66lb.
Third. The front shocks didn't come with a boot to protect the shaft. Is one needed when the shock is installed?
Truck is a 2012 F150 FX4.
Yaris/Scion & Vitz :: Torque Value For 2009 Oil Pan Bolts?
know the torque value for a 2009 yaris oil pan bolts? In another forum somebody quoted a value of 6.6 foot pounds, that seems too small and the wrong value to me.
View 3 RepliesLexus ES 2007-12 :: Torque Specifications For Brake Caliper Bolts
I haven't had luck trying to find the torque specs for the caliper bolts on my 2010 ES350. What are the correct numbers? a pdf diagram would be very useful.
View 1 RepliesGeo - Metro :: 1996 - Loose Head Bolts Causing Overheating
Geo Metro loose head bolts... I have a 96 Metro, and for some reason the head bolts loosen by themselves, leading to over heating and planing head ... well you know.I had a farm for 20 years and took care of all equipment myself, have rebuilt numerous motors, but this geo is the first I have seen where the bolts loosen. This is the third time. I know they are tightened right , because I have the tools and experience, but not with this. Other than jb weld in the bolt holes.
View 7 Replies