Ford Ranger / B-Series :: 1994 - Coolant Loss / Head Gasket Leaking
I am working on my buddy's 1994 Ranger with a 2.3L I4 that has been going thru a large amount of engine coolant. The trucks has approximately 180,000 miles on it. When I had it parked on concrete I have not seen any signs of coolant on the concrete or any signs of coolant leaking. The next place I checked was inside the cab to see if there was any coolant from the heater core and there was not. The water pump has been replaced a couple of years back. I replaced the spark plugs today and did not see anything on the plugs that I would have thought were signs of coolant in the combustion chambers.
With that being said I have not worked on a vehicle with a leaking head gasket before. Would there be any visible signs on the sparks plugs? If so what would I be looking for? When standing in front of the vehicle with the engine running there is a slight smell of antifreeze being "vaporized". Are there any noted issues with this engine that would cause this? Are there any other things I should check? Could it be a leaking head gasket causing this? If so how can I check for that?
Ford Ranger / B-Series :: 1995 - No Spark / Leaking Head Gasket
My 95 Ranger has been a good truck in the 6 years I've owned it. I had to pull the heads to replace a leaking head gasket and wound up having the heads rebuilt due to weak valve springs and worn valves. I replaced the gaskets, installed the heads, get it all back together.....won't start. Fuel pressure is good. Found that there is no spark. While putting the crankshaft position sensor connector back on I noticed it didn't look too good. I replaced the connector and that's all I did and no spark. Long story short, after a lot of research, the coil pack, cps and coolant temp sensor were replaced and still no spark.
Everything has the proper voltage to it. After a little more research I found a post with the same basic issue. His issue wound up being the ecm. So I removed the ecm....it's a used one from a salvage yard. I've owned the truck 6 years so I have no idea when the ecm was replaced. It showed up today and will get installed when I get home from work. I also ran across posts about the camshaft sunchronizer and they should be replaced at about 80K miles. Since the truck has 289K I'll replace it. Still no spark. I'm hoping it's the ecm.
Ford Ranger / B-Series :: 1993 3.0 - Head Gasket Failure / Blowing White Smoke And Using Coolant
Well I finally went and bought another Ranger. Pretty red 5spd 4WD long bed. I knew it didn't run when I got it (crazy leaky fuel line...stupid squirrels), and the owner was pretty sure it had a head gasket failure. He claimed it was blowing white smoke and using coolant. I hadn't been able to get it to run to verify that, but I can't see why he would lie about that.
I finally got the fuel line fixed today (FYI, don't waste your time or money buying those Dorman OEM connector patch kits at Advanced Auto). While we were cranking the truck, I noticed gas escaping the degas bottle the radiator was pressurized before the thermostat should be open. That to me says blown head gasket (crossing fingers it isn't a cracked head) for sure. I tried to get a picture of the dipstick, but in the light it definitely looks like peanut butter. I just wanted to make sure before the massive ordeal of pulling heads/top end work that will follow
Anyway, plan is to fix her up and get her back on the road! Some picture enjoyment .......
Ford 6.0L Power Stroke Diesel :: Loosing Coolant - Head Gasket Leaking?
I LOVE my Super Duty and with only 15k on it (have a company truck) plan on keeping it for a long time. I've had an EGR Delete and new Oil Cooler along with some misc things done to the engine and turbo, about 6g's worth. Now my mechanic at NCB is telling me that the reason I'm loosing coolant is that my head gaskets are leaking. I'm looking at another 5-7 grand which is a no go for me. I'm thinking of doing the work myself, especially since I've seen where i don't have to remove the body to do it.
Okay, here is the question, I've been having a hard time finding a comprehensive list of the parts I should be getting to do the job. Looking for a list or link on what I need to do it correctly and anything I might want to do while my engine is apart so I don't have to do this again?
Ford Ranger / B-Series :: Blown Head Gasket?
I have read all I could find on replacing a blown head gasket and and after absorbing everything that TigerDan posted on here, I dove in and began. After disassembling all the topside junk I finally got the intake manifold loose and got down to the head. I began undoing the head bolts and found two broken bolts. The head won't budge so I am calling in a cherrypicker. I don't know what kind of mess I'll find when the head comes off. I assume the head will be warped or the block may be damaged.
View 6 RepliesFord Super Duty (1999-2016) :: Head Gasket Leaking Into Coolant System
To all those folks that said I had a head gasket putting pressure into my cooling system and causing it to overheat, you were right. It is a 2003 F250 with 80000 5.4 l. I have had to replace mexhaust manifold bolts on left side (horrible job, couldn't get one out). Back fenders are rusted out, under the extended cab rusted, doors are rusting at the bottom. My friend/mechanic said it was time to get rid of it. I don't really have thousands of $$ for a different one, but also, replacing the head gaskets are in the thousands for a repair bill. I have looked at used 2008 250 4 door and they are 20000+++ sheesh, but a new one is out of the question. Do I get the gasket situation repaired?
It does not act up all the time, some times it never overheats, sometimes it will. Somewhat infrequent ( I had one mechanic look at it and he tried 3 different times, and it did not overheat. Temp gage will peg, coolant resevior will overflow, but is not hot (100 degrees). I dont have the really have the money to put into a newer model, but I am worried about being nickeled and dimed to death after dumping a couple of thousand into a head gasket, plus I suppose I need to have the other side manifold gasket/bolts checked too. It seems like low miles to be having issues, yes I realize all will rust, but this year, as evidnet in our area, was really suspect-able to rust.
Not worried about the body, is it worth it to spend 2500 for head gasket repair, or trade up a couple of years, less miles, etc. My worry is, I already had to fix 1 exhaust manifold gasket, know head gasket to fix a cooling issue, do I cut my losses and move to another truck, or spend the money for repairs. I don't really have money for either but want to make a good decision. Truck has not been abused and has been serviced as scheduled. Had to put on new brakes and rotors, as would expect, and ball joints too. Oil looks fine, no contamination, and coolant is clear. Will the head gasket get worse? As I said before, it is intermittent, but I don't trust it for long trips.
Lexus RX 2010-15 :: 2011 RX350 - Coolant Leaking From Head Gasket
I have a 2011 RX 350, leaking coolant from head gasket. It has 113000km, engine warranty is 110000km ...
View 5 RepliesElantra XD (2001-06) :: 2005 - Coolant Leaking Externally From The Head Gasket
Our 05 Elantra (170k miles) is leaking coolant externally from the head gasket. At first I thought it was coming from the freeze plugs, but it's actually leaking from above. I'm mechanically inclined but have no experience with head gaskets. I have access to Alldata but no service manual. Will it tell me everything I need to know? The farthest I've gone inside an engine is removing valve covers car runs great and we like it enough to want to keep it for a while ... I'll also mention I will be replacing the timing belt as well.
View 7 RepliesSubaru - Outback :: 2000 Head Gasket Started Leaking Oil And Coolant Slightly
2000 Subaru Outback. The head gaskets have begun to leak slightly (oil and coolant), even though I brought it in for the recall at 80K and the dealer put in the additive. I recently (111,000 miles) put in another bottle of the additive coolant conditioner and the leak seems to have at least slowed to a trickle. Is it really essential to have the head gaskets replaced? Or could I just keep an eye on the oil and coolant levels and put a bit of kitty litter in my garage? Some of the information I googled indicates that the recall of this car is for an OUT leak and not an INNER leak--which would be worse. Is it true that an OUT leak is not as worrisome?
View 5 RepliesPontiac - Grandam :: 2000 - Smell Coolant While Stopping - Head Gasket Leaking?
I have a 2000 V6 3400 engine. I had the intake gaskets repaired with the "good metal ones" according to the mechanic I had do the job. Cost me $600. Car still has coolant leak it overheats every 3 days or so. Leaves no puddles under car when parked. Can smell coolant when stopping at stop light or stop sign or when parking car. No obvious coolant running down or pooling on the engine. Sometimes it seems like smell is coming from heat vents but no wet spots on carpet or liquid coming out of vent. Took to mechanic again and he said it was the head gasket leaking. Wants $1100 to fix it. Don't have the money. Was wondering if any of these additives you can get at Autozone Etc. may work. It wouldn't be my first choice but financially it's about all I can do right now.
View 2 RepliesFord Ranger / B-Series :: 2000 V6 - Blown Head Gasket / Radiator Fluid Goes Straight To The Oil Pan
I have a 2000 Ranger, V6 4L, and I believe my head gasket is blown, my radiator fluid goes straight to the oil pan. It has probably been leaking for a while, I did not realize it was leaking internally, I had been adding coolant for a few months but thought it was my radiator leaking because it had a crack in the housing, so I had that changed, but then a few weeks after that It gave out. I drained, and flushed the engine twice, and just parked it. My question is, should I just have the head gasket changed, or does it need a new engine because it had been leaking for a while and not sure what kind of damage it has done internally.
View 3 RepliesFord Ranger / B-Series :: 1989 - Signs Of Water Leaking Through The Gasket
My 89 2.9 has gotten water in the oil. One year ago I pulled this engine to replace the crank shaft (defective Ford design 1/2 thust bearing created a nasty grove in the crank allowing it to slide back and forth1/4 inch), new bearings, oil pump, timming chain, all seals and gaskets (not head gasket). The engine had great compression so I didn't do any thing more. Now I have a leak. No oil in water. NO compression leaking off into the water jacket. No "steam" coming from the exhaust. I've replace the intake manifold gasket. It showed signs of water leaking through the gasket, actually bubbles of water trapped inside, so I hoped this was it, but I still have water in the oil. I have now removed the intake and driver side head (head gasket shows now sign of leaking). No signs of water in cylinders. Is it possible to have a warped intake manifold? I have removed it twice, and I was told that some V6's need to be slowly removed VIA de-torque the bolts. I didn't do it the first two times I removed it, today I did. I plan to remove the passenger side head tomorrow. I will take the intake down and have it tested for warping. I have read many stories on this web site of the heads getting cracks, but they all seem to be in or near the valves, I assume that allows water to be burned off as a steam engine OR compression being pumped back into the water jacket.
Is there any other source of the leak that I'm missing? Is it possibly my intake? OR should I go ahead and replace the heads?
Ford Ranger / B-Series :: Coolant Leak From Timing Chain Cover Gasket?
I have 2000 V6 3.0 Ranger and it has sprung a small coolant leak from timing chain cover gasket. I think just few drips after driving a while since I don't see significant drop in coolant level (Took a month to notice level dropped in reservoir) and did not see an active leak while idling. No water in the oil.
The proper repair would be to replace the gasket, but for the age and condition of the truck, I don't think it is worth it. Searching for a cheaper solution, I found K-Seal and see lots of reviews with success. Will it damage the cooling system in anyway? I think it would be worth a try even if it doesn't fix the leak as long as it does not cause any harm.
Ford Ranger / B-Series :: 1991 - Stall Out At Idle / Back Part Of Trans Housing Leaking
1991 2.3L 5 speed .... Okay here's my list of issues.... At idle will stall out, its almost as if i shut the key off, or sometimes taking off it'll sputter and stall, fuel filter has been changed. Back part of the tranny housing leaks, is there a gasket for that?
View 3 RepliesFord Ranger / B-Series :: 2002 B2300 - Lower Hose That Comes Off Of Coolant Reservoir Leaking
I'm about to tear into a friends 2002 B2300 4 cyl. The lower hose that comes off of the coolant reservoir is leaking in the metal part of the line. Close to where it bolts to the block. At a glance, it looks like I have to pull the whole top of the motor apart to get it off since the line runs around behind the motor. Is there a trick to removing this coolant line without a lot of teardown? I'm not finding it at parts stores so I guess it's a stealership part.
View 2 RepliesFord F-150 (2004-2008) :: 2006 - Head Gasket Leaking?
Have a 2006 F150, head gasket leaking bad. It is the drivers side head. How many hours this job is? and does the engine have to come out or the cab have to come off? Has a 5.4L Engine.
View 3 RepliesFord F-150 - 1997-2003 :: 2002 - Head Gasket Is Leaking Oil
My wife has a 2002 F-150 King Ranch 5.4l. Recently I noticed a oil smell and I had the mechanic take a look. He said the head gasket is leaking oil. Not a bad leak but it is leaking. The truck has 160k miles on it. I can't decide what to do...
What generally happens with a head oil leak? Will the engine crater or just keep leaking? My plan was to buy my wife a different truck and I would keep the truck, but I don't wont to keep it if the head leak is terminal for the engine...
Ford F-150 - 1997-2003 :: Head Gasket On Passenger Side Number 3 Is Leaking
I have a 97 with a 4.6 Triton motor I need to replace the head gasket on the passenger side number 3 is leaking nothing else is wrong with motor so I have it torn down to timing chain cover and ready to remove. do i have to take the drivers side valve cover completely off to take timing chain cover off or can I take to first 2 studs out of the drivers side front valve cover and side the timing cover off. I just want to replace the passenger side head gasket and get rid of truck.
View 6 RepliesFord F-150 - 1997-2003 :: Coolant In Cyl 5 After Removing Bad Intake - Head Gasket?
I have a 03 5.4 F150 SCrew... The intake was leaking on the passenger side (water outlet tube meets plastic).
Putting in the Dorman replacement and noticed that the front cylinder drivers side (#5) had a decent amount of coolant in it.. None of the others did. I've drained the coolant already and was wondering should I just put this back together and see?
The water outlet crossing has a hole right next to this cylinder and I can't see any cracks and not sure if the gaskets were leaking under it.
Seems like if the head gasket was blown I would see it in more cylinders? It never smoked or run bad before I got this leak... Drove it maybe 10 miles with it leaking out onto Cyl#1. Ran fine, never missed.
I just don't want to put this back together if the head gasket is blown but I don't know what to do.