Ford Ranger / B-Series :: 2000 - Running Rough And Code For Misfire On Cylinder 3 / 2nd Coil Pack
2000 4.2....Last year I had to replace the coil pack when it started running rough and had a code for a misfire on cylinder 3. It is doing the exact same thing now, same code, same cylinder. Is there something wrong that is causing this?
View 5 RepliesFord Ranger / B-Series :: 1994 - Running Rough At Idle?
Engine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 RepliesFord Ranger / B-Series :: New Plugs Now Truck Running Rough
Although my lil' truck (2006 Ranger XLT, 2WD,with 4-cyl / 5spd, and 115K miles) has been running just fine since I bought it about a year & 5K miles ago, I suspected it still had its original spark plugs and I figured I should change them before problems arrived.
As I suspected, the plugs that I took out looked to be original. I measured their gap and they all had excessive plug gaps - around 0.052" gap. I installed the four new AUTOLITE APP104 (double platinum) and checked their gap, and they were a bit tight at 0.042". My book says they should be at 0.044" gap. But I installed them at 0.042 anyway, figuring they'll burn wider in time.
One by one, I smeared a small bit of never-seize on the plug threads & at the plug-to-cyl head tapered edge. I smeared a dab of Dielectric Grease around at the top of the plug to ease the plug wire re-install and hopefully calm any possible arching. The plug wires came off the plugs easy enough and went back on just as easy.
I hit the key and the engine fired right up. It idled rough as expected. However, it continued to idle rough and if I raised the RPM level, it would respond, but still ran rough. It is throwing a 'Check Engine Light' on the dash cluster now - whereas it wasn't prior to the new plugs.
Ford Ranger / B-Series :: 2002 - Running Rough Like Misfiring
My ranger just started running very rough. Like misfiring, but I think it may be the fuel pump. It starts and drives...but it surges then drives normal, as if fuel is being fed, then starved, then force fed etc. My father asked if I had trouble starting it and to be honest in the last 6 months it was a little harder to start on several occasions. On a few occasions it required more cranking. But that was only a few times.
I tried putting in a fuel injector cleaner and 93 octane gas but it is still running even rougher now. I changed out the fuel filter under the rail about a year ago (maybe 8000 miles ago at most). My father thinks the fuel pump is shot and he laughed because his went on his expedition and he said it is inside the fuel tank and there is no way to get at it without dropping the tank. Is that true? 2002 ranger xl 4cyl
Ford Ranger / B-Series :: 1999 - Running Rough / Missing And Surging At 50 To 70?
I live in Kansas and was home in Georgia for the last 2 weeks. The truck drove great there after a fuel up started missing and surging at 50 to 70 thought it might have been bad fuel. waited till it was low added Lucas fuel treatment and premium gas still was doing it. no check engine light. went to Advance and fuse for light was blown they checked and was getting mass air flow code. unplugged it and seemed to be better, not perfect but better. plugged it back in and went to do it again. Changed mass air flow night before the drive back to Kansas. Ran well from Savannah to north Georgia then started doing it again the rest of the way home. Going to have advance check code again.
View 12 RepliesFord Ranger / B-Series :: 1998 - Running Rough And Now Getting P1151 Code
1998 Ranger 4x4 4.0 Ltr - Runs rough ever now and then and CEL giving P1151 code. Upper and lower intake gaskets have been replaced.
View 14 RepliesFord Ranger / B-Series :: 2003 - Misfire And Rough Running / Flashing CEL
2003 Ranger FX4 Flareside
4.0
Automatic
145,000 Miles
Here's my issue: My Ranger has been running like a dream until yesterday.
I took off on a parts run for my sons Ranger. I got to a stop sign and as I stopped, it started missing and barely running. I nursed it back home and checked the flashing CEL. It was giving me a misfire on #3.
Since I had been planning on changing the plugs and wires, I dove in and got it done hoping that was the cause of the misfire.
Started it up, same thing. I went to the next obvious item: coil. Replace it, still running like crap. Gave up for the night.
Today, I thought I would dig in using the tips here on the forum. Did the spray down...no errant spark anywhere. Tested fuel pressure: 65psi no drop in pressure on acceleration.
Started pulling wires off the coil one by one. Four of the wires resulted in running worse. 2 had no effect. #3 and #6. The coil was producing plenty of spark on all 6 ports.
At this point I was sure it had to be 2 bad injectors. Since I couldn't get injectors tonight, I moved them around after cleaning them a bit and tried my wire test again. The problem stayed on the back 2 cylinders!?!
I tested for voltage on the back injector plugs and I am getting voltage. I also used a stethoscope to listen to all of the injectors. The back 2 seem to remain silent. I have also unhooked the battery for 20 minutes to reset the PCM. Still missing and running rough....
Here's a list of what I have done:
Autolite Double Platinum APP5144 plugs. .062 gap
Autolite Pro Series wires #97051
BDW E97P Coil
New air filter
What should I do next? I really don't know where to go next.......
Ford Ranger / B-Series :: 1990 - Rough Start - Running Lean?
]I recently bought a 1990 ford ranger with a 2.9 @187,000 miles. That being said I went through and changed a few vacuum lines, the oil, air filter, pcv/grommet, and fuel filter.
The problem is it hates to start. I could crank on it for 10 seconds and not a single thing. Sometimes if i turn the key to the off position, wait a second, and try again, Ill get the truck to fire. When it does fire up it just reeks of the lean exhaust. It also gives me some hesitation when I rev it. I did a fuel pressure test (KOEO) last night and it gave me 32 psi and within a minute the needle fell to about 25 psi. I hear the fuel pump run for only 2-3 seconds too.
I've already pulled the MAF off and cleaned it, replaced the TPS, and did a fuel pressure test. The fuel filter is brand new
Ford Ranger / B-Series :: Sputtering / Rough Running Situation Once Warmed Up
'86 Ranger, 2.3L, Automatic transmission.
Been having a sputtering/rough running situation once warmed up, replaced every so often with open loop smooth running. Lately, have had several occasions where the truck stalls and will not restart after a hard right turn (fuel pump powers up, tho) After 30 or so minutes of repose, truck will restart and run.
Recent History:
During the last 1-1/2 years, had cylinder head rebuilt and reinstalled. Had to run it all winter w/o EGR tube attached because of bad fitting at exhaust manifold. Replaced the fitting last spring and replaced cat back exhaust system. Had manifold hole plugged with pipe plug all winter. Have had a diagnosis of poor compression in the past, have not rechecked compression since head rebuild, but did have a noticable increase in power.
Have checked base ignition timing and it is correct. Valve timing appears to be as it should be. Have not had the opportunity to check for spark during one of the breakdowns, since I had no tools and it was night time.
The codes:
Early in Fall, got 14, 21, 24, 34. The 14 particularly interested me, as it suggests ignition problems.
Just before pulling the distributor, I checked codes again; 14 had disappeared as did 34 (EGR issues I resolved above) but I still got 21 (coolant temp out of range) and 41 (no HEGO switch) So I left the distributor alone and replace the HEGO sensor and cleared codes.
Last code check, just got 21(coolant temp sensor voltage out of range) and 24(air charge or Vane air temp voltage out of range) There is very little heat on cold days, full radiator and I've "burped" the cylinder head on an incline more than once chasing trapped air.
I'm suspicious of the TIF module, since the stalling is after warm up and self corrects. It was replaced once perhaps 12 years ago.
Ford Ranger / B-Series :: 1985 - Running Rough - Bogging Out And Stalling
I am fairly new to this stuff but I just got a 85 Ranger 4x4 and its running pretty rough it will be fine then all of a sudden it will bog right out and want to stall so I have to keep my foot planted on the gas and it pops and spudders and eventually runs normal again? Its a 2.8 V6 carb...
View 14 RepliesFord Ranger / B-Series :: 1996 - Running Rough / Smooth Out A Bit When RPMs Raised Up
Recently bought a 96 4 cylinder 5speed 2wd ranger. 200xxx miles on it and its former owner had a young guy change spark plugs . Truck ran fine before, but after is when the rough running showed up.
A quick check of the plug wires and there locations looked correct and also tested the wires for spark with a timing light attached to them, checked shows all are firing.
Seems to smooth out a bit when rpm's are raised up, but still acts like not running smooth.
I swapped out plugs. Looks like they haven't been changed in a long time .Some of the straps are burnt and are shorter than they should be, but still runs rough, very little improvement .
Check vacuum lines for leaks/breaks and all looked good. removed line off brake booster and plugged, didn't matter.
It doesn't throw and check engine lights. It does smooth out some as the rpm's rise, but still not smooth .
Ford Ranger / B-Series :: 1987 - Running Extremely Rough / Exhaust Smell
I have a 87 ford ranger pickup, it is running extremely ruff. You can smell the exhaust and it smells super rich and is even spitting fuel out of he exhaust. when I bought the truck the wires were cut on he oxygen sensor, so I put a new oxygen sensor in it hoping that it would lean out the fuel. The truck has duel tanks on it, but the back one is off and it is draining fuel out of the line when it is running. I don't know if the catalytic converters are plugged too, the truck only has 65,000 miles in it. or maybe its a vacuum line leak?
View 4 RepliesFord Ranger / B-Series :: 2003 3.0 - Misfire On Cylinder Six / Running Rough And Check Engine Light On
I have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 RepliesFord Ranger / B-Series :: 2002 - Started Running Rough / Trying To Stall Out / Black Smoke Coming From Exhaust
2002 Ford Ranger edge 3.0 flex ... Truck was running fine and giving me no issues. I woke for work the other day and went to get coffee and truck wouldnt start. I could hear fuel pump running and knew it wasnt that, it was acting flooded. So today I pulled fuse from fuel pump relay, and got it to start. Put the fuse back in and ran to gas station. On the way to the gas station it started running really rough, very low and rough idle, trying to stall out. I noticed it had black smoke coming from exhaust. I got it home, and got it to start barely, and it has the same very low and rough idle, but my oil gauge was going crazy, flickering back and forth all crazy, and the idol is terribly rough and eventually stalls out. Earlier today I did put new spark plugs in it, but not sure that has anything to do with the issue. I also hooked it up to a computer and it isnt throwing any codes.
View 13 RepliesFord Ranger / B-Series :: 2000 3.0L - Idling Rough / Hesitation While Driving
Finally back able to start working on the Ranger and have a few questions.
When I got this thing back from my son it was running rough. I've fixed all the codes it was getting so no luck there now. Not sure how to explain it but, it feels like it is cutting back when driving at a steady speed and it idles rough. Not really like a miss but more like a hesitation when driving.
I've cleaned the MAP and IAC and changed the fuel filter. I also pulled the plugs and they looked good. My son installed new plugs and wires but he used the E3's and not sure how, or if, you're suppose to set the gap. I haven't checked the PCV yet because haven't figured out how exactly you get it out without pulling the intake.
So, where to look next? I'm kind of thinking the cam sensor but think I'll leave that to a shop sense I want the shaft replaced at the same time.
Ford Ranger / B-Series :: 1988 V6 Starts And Runs But Shuddering - Cylinder Not Firing?
'88 Ranger 2.9L V6 starts and runs but shuddering. Most noticeable when shifting and revving the engine. Will a dead cylinder cause this? How do I check?
View 2 RepliesFord Ranger / B-Series :: Engine Starts Very Briefly Then Begins Shuddering Violently And Dies Within A Few Seconds
'02 Ranger XLT, extended cab, 4X4, 4.0L SOHC, 5-speed manual, 114K miles.
Problem has occurred twice. After extended run time and engine fully heated, when I get home and shut it down, then attempt to restart within a short period of time, the engine starts very briefly, then begins shuddering violently and dies within a few seconds. Re-attempts to start result in a very shuddering attempt to run for a couple seconds, and then it dies. After a couple of re-attempts, it doesn't even attempt to start; just cranks over with no results. Has to sit about 7-8 hours before it will restart.
No OBD II codes; Passed, no codes shown. I purchased a crank position sensor, but haven't installed it yet: just a stab in the dark after hearing other people's experiences with other vehicles.
First occurrence followed a lengthy trip in heavy stop-and-go traffic. Shut it down when I got home, then attempted to re-start after a few minutes to run a short errand. Sat for two days without any re-attempts; then restarted and ran fine on first try a couple days later.
Second occurrence followed a couple hours of hitting yard sales with the neighbor, in which time I did not shut the truck down; just left it idling while we perused the sales, for fear it wouldn't re-start. Reckon it's a good thing I did, 'cause when we got home and I shut it down and attempted to leave again shortly thereafter, it malfunctioned as described.
Retries failed after sitting 4-5 hours, but after eleven hours of sitting, it started right up and ran normally.
Ford Ranger / B-Series :: 1999 - ABS Activates At Slow Stops
I have a 1999 ranger 4x4 , when I'm going to a slow final stop the abs kicks in ,doesn't do it every time , there's no abs warning light , took it to the ford dealer they scanned it and said it was the left front hub & bearing assembly, said the sensor wasn't reading the back of the bearing assembly. I can't understand way the abs light isn't on, is there anyway to clean that they want to replace the hub & bearing, Is a use hub & bearing replacement a good way to go? They told me I could pull the fuse and kill the abs, but I find three fuses I pull aII three and got a speed sensor check engine code. I hate to replace that hub & bearing when there's no problem with the bearing ,Is there any way to deactivate the abs, by the way it's 4 wheel abs.
1999 FORD RANGER 4X4 4.0......
Ford Ranger / B-Series :: 2003 XLT 4.0 Stalling At Stops / Low Idle
My 2003 ranger xlt 4.0 has a stalling problem. The engine light came on in aug and I had it coded at AutoZ and there was a code for the oxy sensor, changed that and didn't work so I took it back. In oct I had it coded and it said the air int temp sensor which i was informed was part of the mas airflow sensor, changed that the beginning of nov, got the computer to reset and it still didn't fix it.
Took that part back and had it coded again a few days later and several codes came up AutoZ code 1732 and the the OEM number to cross for them were: P2195 , P0300 , P0316 , P0174 , P0171 , P2197 . Reset the comp yesterday and as soon as the light came on had them code it again and it came up AutoZ code 1732 OEM # to cross P2195. I guess my next step will be to take it to the dealers to get diagnosed..