Ford Ranger / B-Series :: 1995 - Rough Idle And RPMs Drops?
1995 ford ranger with 4.0. It idles rough. Replaced MAF TPS fuel pump fuel filter fuel pressure regulator upper o2 sensor. IAC.. still idles rough RPMs drop. It isn't as bad since replacing MAF but still not right. What else is there.. Cleaned out the air intake port it was gummed up. Don't know what else to do?
View 3 RepliesFord Ranger / B-Series :: 2001 / 2.3L - Misses At Low Revs And At Idle
My new-to-me 2001 Ranger 2.3L runs great except for this one problem: At under 2000 rpm, if I give the gas more than the gentlest tickle it misses and bucks until I back off. It also misses at idle. There is no CEL but I did pull a P0442 code which points to the evap purge valve. At above 2K rpm, it runs like a champ and I can floor it, except when under load such as climbing a hill.
Could this be the problem, or should I look elsewhere also? I'm not one to just throw random parts at a problem. The previous owner thought it was old gas or an injector, but I would expect it to run poorly all the time. The service writer at the Ford dealer thought it sounded like an electrical issue, but coil, plug wires and plugs are new.
Ford Ranger / B-Series :: Random Sputter At Idle And Misses Around 4k When Get Into Throttle
I have a 2000 3.0l ranger. I have been battling an ignition problem. every time the engine is cold it runs terrible like only 3 or 4 cylinders running terrible. if u put a timing light on the wires the pulse comes and goes on random wires. and when it quits that it has a random sputter at idle and misses around 4k when u get into the throttle ...
I have replaced plugs twice and the coil with motorcraft parts and the wires are new autolites. I have also replaced the thermostat and fan clutch it was getting hot in the middle of this other issue ...
Every time I replace something it runs great for a few days then back to running terrible again. am I missing something else do I need to look at a computer or map or tps sensors, or something like that ...
Ford Ranger / B-Series :: 1995 - After Warm Up Starts Idling - MAF?
I have a 95 4.0 EFI inside of my 83 Ranger. Once the motor warms up, it starts to have an idle issue. I have to press the gas, in order for it not to cut off. Here is a video I posted a while back. A person suggested that it could be the MAF needed to be cleaned. I did that, and it did not work.
View 9 RepliesFord Ranger / B-Series :: 2005 - Bogs Down At Idle When Warm?
I have a 2005 ranger, 3.0 and automatic trans
The truck runs fine until it is warm... runs great down highway... stopping at a light or stop sign is horrible, It will act like the (old term ) carb is flooding out.
I put it on a meter It said tps so I replaced it. then it said number 4 cyl no power so I put new plugs in.... I do not hear any vacuum leaks, and It runs like a top when cold.
Ford Ranger / B-Series :: 1994 - Idles Rough / Stalls When Cold But Runs Great When Warm
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 RepliesFord - Explorer :: 2003 - Intermittent Rough Idle / Periodic Drumming Sound
2003 Ford Explorer 4.6 liter AWD. Having some kind of VERY STUBBORN idle / emission problem. When it started it was an intermittent rough idle, mostly going too low or making a periodic "drumming" sound that could be felt and heard at the air cleaner box. CHeck engine codes were PO 442 evap system leak. I first cleaned and inspected throttle body, mass air flow sensor and idle air control valve. I inspected hoses for leaks, including spraying cleaner to see if I could detect idle changes / leaks. I then replaced Idle Air Control Valve. Did not seem to cure problem . SO took it into Ford Dealership and they smoke tested and said needed Vapor Management Valve and Vent Solenoid. I replaced VMV myself. Idle no longer "rattled" but when driving and braking the idle would drop down very low and sometimes not "kick up" and would die. I then took it back to dealership to have them replace the vent solenoid and reprogram the PCM. Still doing it. They said I might have a defective (new) Idle air control and to replace it- otherwise they dont have a clue.
View 2 RepliesFord Ranger / B-Series :: 1994 - Running Rough At Idle?
Engine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 RepliesFord Ranger / B-Series :: 1998 - Rough Idle At Cold?
I understand there is not much adjustable on my 98 Ranger (2.5L) as far as idle speed and mixture. It runs rough when started cold. Is this a sign to replace spark plugs?
View 2 RepliesFord - F250 :: Rough Idle - Misses For About A Mile Or So Until Temp Rises
2004 ford f250 superduty v10, truck has a cold run miss, no matter the temp. (0deg. or 100 deg.) when i start truck it misses for about a mile or so until temp. rises, after that it runs fine all day even if i park it for a few hours,next day same thing. I have changed all 10 plugs, gas filter, air filter, cleaned mpf censer, throttle body. Also it shows no codes, and there are no codes in history.
View 3 RepliesFord Ranger / B-Series :: Rough Idle At Start Up - Spark Plug 4 Keeps Going Bad
I'm getting tired of the same problem about every 6 months. Plug #4 keeps going bad. Its been doing this for years. It starts with rough idle when first starting up that clears up quickly then eventually it leads to a misfire when accelerating. Every time this happens I replace plug #4 and its good to go. Just recently (roughly 6 months ago) did a full tune up and all new injectors. About a week or 2 ago it started its rough idle at start up and just the other day it started misfiring again. What would keep causing this??
View 14 RepliesFord Ranger / B-Series :: Easy Start / Rough Low Idle And Stalls
My 2005 2.3l Ranger ran great. I moved a trailer about 150 feet and stalled the truck backing it up. Stick shift. Unhooked the trailer and pulled back into the parking area....all the sudden the truck has extremely rough idle and stalls. It runs good on the highway. AutoZone ran a OEM number to cross: P0171.
I cleaned the IAC with intake cleaner. No Luck
I unhooked battery for 15 min. No Luck
I sprayed intake with 1/2 can of intake cleaner. No Luck
I did not have a tamper torx to remove the MAF. What next.
Ford Ranger / B-Series :: 2003 V6 Rough Idle / No Power On Highway
168K, to date, replaced
rear 2 cat's
Timing chain and gears
cam sync assem.
Plugs, wires, dis block,
Why.............. Read on
This 2003 ranger 3.0 v6, run very hard at idle, yet it runs and you can drive it around town, ""at"" low rpm, and no hills but it gets from point a to point b
I have no pre ingintion, but a plug that was only 60 days only was burnt out completely on 3rd cyl. bank 1 or as ford call it #3, i am telling you this thing seem like it running on 4 cyl,s kicking back and forth, and replacing everything above made no difference.
On the highway, as long as it is flat or down hill 75-80 mph, as soon as a hill or power to pass is needed it bogs down and slows it self to about 45 mph, I have been though everything i can think of and my next move to to start pulling heads, but i wanted to ask here first.
Ford Ranger / B-Series :: 2002 XLT - Rough Idle - Misfire On Cylinder 3
I have a 2002 ford ranger xlt 3.0 i just rebuilt the entire motor about a month ago and was having a high idle problem for the longest time. turns out i had the iac on backwards. but now that it idles down around where its supposed to it has a rough idle has a little shake to it. starts up right away but when i drive down the road around 3000-3500 rpms its missing on cylinder #3 from what the code I am getting "multiple cylinder misfire, #3 cylinder misfire" I've replaced plugs and wires. camshaft pos sensor. I am getting 65 lbs of fuel pressure. spark on all cylinders. I am really at a dead end here. Also every time I take the plugs out to look at them they look brand new.
View 14 RepliesFord Ranger / B-Series :: 2001 - Rough At Idle / Misfire In Cylinder 1
So I have a 2001 ranger 2.3l . Runs very rough at idle.code says misfire in cyl.#1. I have changed plugs, wires, coil packs all motocraft. I did a compression test..
#1.170
#2 180
#3. 185
#4 . 180
Compression seems fine,but where do i go from here? Anything else i can check/replace to solve this?
Ford Ranger / B-Series :: 1999 - Rough And High Idle At 850 RPMs
1999 B3000 with a 3.0. The truck idles at 850rpms. When it starts it idles at around 1000 and runs very rough. When I disconnect the IAC the engine dies. The AC also has problems it blows cold at idle but at highway speeds after 7-8 minutes running the compressor kicks out. One can turn it off and it blows cold again after a few minutes.
View 5 RepliesFord Ranger / B-Series :: 2007 - Rough Idle At Low RPM Either In Park Or Drive
2007 Ranger 4.0l, idles rough at low rpm, in park or drive, with or without the AC on.
View 1 RepliesFord Ranger / B-Series :: 2002 - Rough Idle Codes / Cylinder 2 And 3 Misfiring
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 RepliesFord Ranger / B-Series :: 1999 - Stalls / Rough Idle And Engine Dies
I have a 1999 B4000 4.0L with 160K miles on it. Bought the truck new. Up until about a year ago it ran perfect but has developed an idle, stalling and occassional jerky ride problem. It occurs at any temperature, engine hot or cold, A/C clutch on or off and in Park, Drive or Neutral. When you start the engine it will not idle unless you keep your foot on the gas. The idle speed will drop to 200-300 rpm and the engine dies. Sometimes you can barely tap the gas pedal and the rpm will shoot up to normal idle speed (about 900 rpm) and stay there a few seconds then begin to drop again. If the engine is cold it will often die a couple times after starting even with the foot on the gas and then about the 2nd or 3rd time run with your foot on the gas.
At stop signs and red lights you have to keep your foot on the gas to keep it running. If you are approaching a stop sign and take your foot off the gas to coast to a stop and brake, the engine rpm will drop and the engine will die. It always starts fine though. Once you are driving it generally runs just fine at low or high speed. You can generally set the cruise control on the expressway and cruise right on. However, sometimes all of a sudden the truck will start bucking and jumping as if it has a terrible misfire. It usually lasts a few seconds and quits. Often if you step on the gas it quits. Even less occasionally the engine will begin to slow as if it is starved for fuel and slow down. You can press the pedal to the floor and it sputters a bit then picks up and runs fine.
I have read about all the threads in this forum and others and tried some of the suggested fixes but it still has the problem. I have tuned it up with new plugs, wires, fuel filter, air filter and PCV valve. Based on some of the forums advice I have replaced the IAC valve, the EGR valve and EGR Pressure Feedback Sensor, and cleaned and inspected the MAF sensor with MAF cleaner. I have checked all my vacuum lines and no leaks there and checked the engine timing which is fine. Fuel rail pressure and engine compression are also fine. Spark plugs show no clues, exhaust is clean and the engine uses virtually no oil. There has been no tear down on the engine like removing the heads, cam, timing gears or any of that and the engine is completely stock.
It shows no codes related to the problem. Two or three months after the problem started I showed a code that indicated an injector problem, traced the problem to a bad injector, replaced the faulty injector and it was fine. That took care of that code but didn't solve the idle problem. In my younger days I was into drag racing and I rebuilt engines, swapped transmissions, etc. and still do my own tune-ups today so I am fairly familiar with auto repair and have most of the tools for testing newer cars but this one stumps me. As a last resort I'm about to take it to the dealer.