Ford Ranger / B-Series :: Converter Won't Lock Up
I have a 95 ranger with an overdrive auto. If you put your foot in it the converter wont lock up, you can get the tack past redline, but if you let off and the rpms drop below 2000, it locks up and holds until you apply the accelerator to much and it kicks it back out. Also the speedometer bounces and may not read right, abs light is sometimes on and it won't idle below 1000, I've checked for vacuum leaks already.
View 2 RepliesFord Ranger / B-Series :: 1994 - Rear Brake Lock Up?
Under mild-heavy braking, the rear brakes on my ranger lock up... EVERYTIME. Not just when its wet, or humid. Everytime I hit the brakes hard they lock. I think I'm getting little, to no pressure to the front brakes either. Could it be just a Proportioning valve?
Truck is a 94' 4.0l V6, RCLB, Auto, 4X4.
Ford Ranger / B-Series :: 1990 - TC Lockup Was Working Now Won't Lock
Just picked up a 90 Ranger last night, 4.0 EC, good ole A4LD, from a recipt I found has 70K or so on rebuild, was driving it today and the TC unlocked, and now it won't lock back up. I checked fluid and it was a little low, topped it off and drove it, and it was the same thing. I'm kinda new to thease A4LDs I know they can have issues, but can be good too. Just want to know whats going on so I can fix it! No codes were found when I scanned it. Trans otherwise shifts fine, you can feel it go into OD but no lockup.
View 13 RepliesFord Ranger / B-Series :: 1998 4x4 Front Hubs Will Not Lock In
I have a 98 ranger4x4 front hubs will not lock in. replaced vac lines that were rotten still will not lock,checked vacuum at solenoid had vac for a min or so then it stopped, ran vac strait to main vac line for continuous vac and they still will not lock in, had 4 wheel just the other day. What can I check or do besides set it on fire.
View 1 RepliesFord Ranger / B-Series :: 1993 - How To Replace Key Lock Cylinder
I am trying to replace the key lock cylinder (where you insert your key to start the truck) in my 93 Ranger. Using the Haynes manual, I have removed the steering wheel cover (I don't have airbags), pulled the steering wheel, removed the 3 plastic decorative shrouds and looked at a naked steering column assembly. The manual says there is a 1/8" hole on the bottom of the steering assembly where you can push up the actuator pin to release the lock cylinder assembly.
I looked and looked (even with a flashlight) and could not find a hole. I looked at the new key lock cylinder assembly and found the little actuator pin so I sorta know where the pin would be in the installed assembly. The entire key lock assembly is enshrouded (is that a word?) in the cast aluminum steering assembly.
There was a small metal plate - but that plate is just for access of the release of the steering wheel lock actuator (so I carefully bent it back!!). I know all this is for theft protection, but the truck is co safe I can't even replace the lock assembly.
Ford Ranger / B-Series :: 1996 - Ignition Lock Cylinder Won't Reinstall
My keys got stolen from my ignition (battery had died because key was left in ACC and I assume the attempted car jack ended in a key theft for some reason.)
The Ranger is 96, tilt steering with plastic shrouding and column shift A/T... I followed the procedure recommended for exchanging the cylinder without the keys:
-drilled retaining pin
-drilled key slot
-manually removed parts with needle nose
-cleaned, greased and went to reinstall.....
I discovered the small metal washer between the green plastic washer and the gear was broken in half because I nicked it with the end of the drill bit. I inspected this and from what I can tell it looks like the green plastic washer is designed to hold onto the metal washer, the two of them together, from what I gather are designed to keep the gear from moving sideways or tilting. I figured that the washer should do it's job even in two pieces if I could get it in there straight and get the green washer to grab it.
Anyway I stuck it all back in there, slid the new lock cylinder in in run position, and nothing good happened. It's in the whole way, I can see the retaining pin centered in the whole from underneath, but when I try to seat the retaining pin it won't budge. I tried to align the parts at a million different angles and I just have no luck. I am planning on replacing the little metal washer, but I don't feel like it being broken alone is enough to keep all parts from functioning properly. I am stumped because I did the procedure step for step and there is nothing else apparently broken or damaged. The only other factor is that the steering wheel is locked and that sometimes made the other cylinder hard to turn, but it freed up usually with a little wiggling, this cylinder won't budge.
Ford Ranger / B-Series :: Removing Manual Door Lock Cylinder
I recently bought a 1994 Ford Ranger, XLT 4 cylinder supercab. They lost the door keys when they replaced the ignition because they never locked their doors. I bought new lock cylinders with keys and set out for an adventure. Removing the metal clamp that holds the cylinder in place was actually easier than I thought. It's that darn plastic piece connecting the cylinder to the rod for the lock system that will not break or come off. Here's the best picture I could find real quick. How do you get that vile piece of 20 year old plastic off? It's in a difficult place to get tools in there, and I can't seem to get leverage with a small screwdriver anywhere. What tips and tricks do y'all have?
View 1 RepliesFord Ranger / B-Series :: 1991 - Location Of Door Lock Wire Loom?
It looks like my door lock wire looms go under the hood but I haven't had any luck finding them. Install an alarm with negative 500Ma pulse to operate them ? I have relays but am also wondering if the truck has its own somewhere that I can piggyback onto. I know the colors are Pink with a yellow stripe and Pink with a light green stripe.
View 7 RepliesFord Ranger / B-Series :: 2007 - Traction Lock Differential Making Noises
My 2007 3.0L XLT 2WD Ranger with 7.5" traction-lock differential started making expensive noises last weekend coming from the rear end. Shop has not yet opened up the differential because the initial though was just do a swap.
Turns out that 7.5" LS is hard to find, plenty of open diffs available. So I suggested that I'd rather swap in an 8.8" LS rear end anyway but turns out that these are also hard to find. Was a LS rear end option just not very common? or do these get scooped up just as fast as they become available?
Ford Ranger / B-Series :: Steering Wheel Lock Damaged - Popping Noise When Turning
While in the locked position, the steering wheel was purposely jerked hard to disable the mechanism on a 1996 Ranger. Now the truck will not steer easily or smoothly and a popping noise is evident when turning. I'm not concerned about having the wheel lock, but would like to be able to return driveability to normal.
The same guy who caused this damage also damaged the ignition. No key is needed to turn the switch now.
I'm lost as to how the steering locking mechanism works and wondering if I need to tear apart the column or if maybe there is a locking pin accessible that needs to be removed to regain driveability.
Celica :: 1988 - Key To Trunk Lock Won't Turn
The key to the trunk lock on my 1988 Celica won't turn. I don't have the original key. Could be that I have the valet key. All other locks (ignition, door and dash door work. I will probably get a replacement from the junkyard if I can find a car with a lock and key. Other trunk locks are interchangeable with the celica???
View 6 RepliesPrius V :: How To Disable Nav Lock While The Car Is In Motion
I have a 2013 Prius v and wanted to know how to disable to the Nav lock while the car is in motion. I want to make it so that my passengers could use it while I am driving.
View 3 RepliesSaturn - Sl :: How To Disable Power Lock
Can I disable the power lock on my Saturn SL1? Its locking and unlocking the front doors all by itself, draining the battery no doubt. Can I pull a fuse? If so, how find the right one?
View 3 RepliesPassat (B6) :: Disable Auto Lock After Timeout
Is it possible to disable the auto lock feature after time-out? I am not referring to the auto locks after driving 15kph. I am referring to when you unlock the doors with the remote and then don't open any of the doors for a minute or two. If you do not "wake" the car by opening it, the doors automatically lock again.
This is my most hated feature. There will be times when I unlock the door from the house and walk out to the car to get something. If I don't open a door within 1 minute, its locked again. Now I just have to carry the key for the most trivial things. Is this a menu option or a vag option?
Ford Super Duty (1999-2016) :: 2002 - Disable Automatic Door Lock Mechanism?
Can I disable the automatic door lock mechanism? Maybe pull a fuse? All of a sudden the locks start locking and unlocking over and over and the lights dim. I would like to disable the automatic and use the key to lock and unlock the doors. It is a 2002, F-250-Super Duty 4x4 SuperCab.
View 5 RepliesFord F-150 (2004-2008) :: Remove Ignition Lock Cylinder?
How do I remove ignition lock cylinder to take and get new set up?
View 4 RepliesSanta Fe (CM - 2007-12) :: No Honk When Press Remote Button Twice To Lock
I have a 2011 Santa Fe. I had to take it in for service in April because the shift lock was not acting correctly. Since I have gotten it back, it will not honk when I press the remote button twice. It did before the service was performed. The lights flash properly and the doors are locked, but I still want it to honk sometimes. Is there something that was turned off that I can turn back on?
View 8 RepliesPrius C :: 2012 - When Press Fob Key To Lock / Unlock Only Get A Flashing Light
I have a 2012 Prius C II my question is why is that when I press the Fob key to Lock/Unlock I only get a flashing light. (Headlights) there is no sound at all. How do I activate it so it flashes and have sound?
View 4 RepliesIsuzu - Trooper :: 1988 - Dying At High Elevations / Vapor Lock?
Recently, my 1988 Isuzu Trooper began dying at high elevations (above 7,500 feet). I have had the car for ~7years and have never had this problem. That is, in the past, i've been able to drive it up to 9,300 feet with no problem. Could this be vapor lock? If so, why would vapor lock all of sudden start happening? If not vapor lock, what could it be?
View 5 Replies