Ford Ranger / B-Series :: Removing Manual Door Lock Cylinder
I recently bought a 1994 Ford Ranger, XLT 4 cylinder supercab. They lost the door keys when they replaced the ignition because they never locked their doors. I bought new lock cylinders with keys and set out for an adventure. Removing the metal clamp that holds the cylinder in place was actually easier than I thought. It's that darn plastic piece connecting the cylinder to the rod for the lock system that will not break or come off. Here's the best picture I could find real quick. How do you get that vile piece of 20 year old plastic off? It's in a difficult place to get tools in there, and I can't seem to get leverage with a small screwdriver anywhere. What tips and tricks do y'all have?
View 1 RepliesFord Ranger / B-Series :: 1988 - Press Key Lock To Remove Key - Disable Key Lock?
On my '88 Ranger, there is the key lock that needs to be pressed to remove the key. When I changed the ignition cylinder, I darn near went ahead and removed it. I though I better check here first, and see if I was going to disable some other function I don't know about.
View 1 RepliesFord - Explorer :: 1991 - Back Door Won't Lock
I just bought it off my friend yesterday and I noticed the back door doesn't lock, the glass part doesn't either. How I could fix it?
View 7 RepliesFord Ranger / B-Series :: 1987 - Dash Light Out - 4x4 Wire Diagram?
My dash light fuse blew. I checked with a meter and I have a short to ground somewhere in the wiring for the lights. Everything else seems to be working fine.
Is there a copy of the wiring diagram somewhere?
I have the big ford shop manual but I't doesn't have any diagrams. (might be missing pages, I got it off Ebay and the index is missing T-Z).
I have the Haynes but it doesn't have the diagram for the dash lights.
Ford Ranger / B-Series :: 2000 - Wire Color For Engine Temp Sensor?
I need to know what the wire colors are for a engine temperature sensor connector (2-wire) are and the correct wiring diagram to get the temperature gauge to work again
View 1 RepliesFord Ranger / B-Series :: 1991 - Turns Over But Will Not Start
My 1991 ranger with a 4.0 turns over but will not start. It acted like it ran out of gas put again seems to do ok then it did same thing it sat over night then would not start so I thought I would put some gas in the intake so it starts ran real rough but smoothed after a few minutes ran fine after that next morning same thing no start did same put gas in intake at first no start just turned over didn't even try let it sit for awhile then tried again it fires up ran rough but ran now I get nothing just turns over pulled codes 22and 122 replaced both had ignition mod checked its good new coil pack no change so at this point i hear fuel pump kick on fuel getting to fuel bar but seems a bit week on pressure going to get pressure gauge and see what it says but in the meantime I am loosing my mind...
View 9 RepliesFord Ranger / B-Series :: 1991 - Front Hub Comes Off With Wheel?
I recently bought a 91 Ranger 4wd for my son. The guy I bought it from put new manual lock outs on it. every time I take the tire off on either side the hub comes with it! Is there a clip or retainer missing? If so what and where can I get one?
View 4 RepliesFord Ranger / B-Series :: 1991 2WD - EEC Fuse Keeps Blowing
My dad's 1991 Ford ranger 3.0 2wd just died on him when he was driving home and I checked to see if the truck had a spark and it did not so I replaced the ignition control module, then ignition coil, then distributor and rotor cap(plug) and I put new plugs and wires on it a few months back too. I also checked to make sure that the timing chain was working as well (while I had the distributor cap off). Then I realized that the EEC maxi fuse was blown. I then found a fourm that said it might be the relay so I replaced the EEC and the fuel pump relays while I had them both out. Every time I put a new 30 amp fuse in the EEC slot and turn the key to start it the fuse blows and the truck won't start. What might be wrong?
View 1 RepliesFord Ranger / B-Series :: 1991 - Won't Start But Crank Great?
Getting the Banana ready for it's smog test appt at the shop last night (it WAS today) Check engine light had popped on and it had been starting to sputter and surge at the idle occasionally for the last few days so I took a look at the MAF and saw dirty wires. Aha I can fix that, a couple squirts of MAF cleaner, plug it back in and voila! No more light, the Banana ran down the road around the block, over the hill and through the dale like a champ. I shut her down and call it a night.
This morning, hop in and fire the Banana up like usual and all I get is a nice peppy crank over. The Banana has had a bunch (pun intended) of new parts throw at her recently... new battery, starter solenoid, plugs and fuel pump relay and fuel filter. All within the last couple of months.
Out of complete disbelief, I ground on the ignition for a little while and she finally kicked over and sputtered to life. I let her idle a couple of minutes and things seemed fine so off we go. I make it about a block before the Banana starts hiccuping and bucking like something possessed and dies.... kaput.
The Banana has a 3.0, manual transmission and at least half a tank of fuel. Long story short and a tow truck ride home again, half a day trying unsuccessfully to pull a code, any code.... nothing. She will half-heartedly cough and spastically run with ether shots and near as I can tell I'm not getting fuel to the fuel rail relief port. I'm really hoping there is some way to diagnose a faulty fuel pump without having to drop the tank and fish the damn thing out.
I'm not hearing it run when the ignition is turned on but then again I don't think I've ever heard it run. Any other things to try before I replace the pump itself???
Ford Ranger / B-Series :: 1991 - Throttle Hesitation When Accelerate
My ranger is an 89 but it's got a 91 motor in it, 2.9 V6. When I accelerate it hesitates before actually accelerating which makes me think the TPS is bad. Probed and tested and I got .85V throttle closed and 4.65 at wide open. Specs call for .8V - 4.5V
I'm not sure if there's an allowance of fluctuation, but is that high enough to point out a bad TPS? If it's not the TPS, is the ignition timing off or what else could it be?
Ford Ranger / B-Series :: 1991 - Noise Under Hood - Filters?
1991 2.3 l. Thought I had an exhaust manifold Leak. Replaced gasket. New gasket didn't work. Removed gasket and mounted manifold to engine metal to metal, still and noise. Installed New manifold with gasket. Still same noise. Am thinking noise not coming from manifold. Torqued all bolts to spec. Could it be lifters .
View 9 RepliesFord Ranger / B-Series :: 1991 - Take Very Long Time To Start?
Grandson 1991 Ranger 3.0 v6 69,000 miles We have a long start issue after it has sat for 30 mins. plus. If you open the throttle part way while cranking it will start fairly easily. Fuel pressure comes up instantly when you turn on the key. It runs at 39 psi pull the vac line off regulator it jumps to 49 psi. Fuel pressure does drop to about 30 psi after setting an hour. It kinda acts like it is flooded when it starts. so far we have done a complete tune up plugs wires cap and rotor. The ignition module has been replaced twice last one a real Motorcraft. New fuel pump and filter. Cleaned the fuel injectors with Ford cleaning system. I will replace the coil next and maybe clean the iac.
View 14 RepliesFord Ranger / B-Series :: 1991 - AC Suddenly Stopped Working
I have a 91 Ranger that the A/C was working great in but all of a sudden it stopped working even the fan. I turned it of and back on and it started again but then just stopped for good I can get the fan to work sometime, but no cold air. What it might be?
View 2 RepliesFord Ranger / B-Series :: 1991 - No Power To Fuel Pump?
I can't get power to the fuel pump on my 91 ranger 3.0 5 speed. I just bought the truck and replaced all the relays checked all the fuses under the dash and under the hood. If I jump the relay it comes on and wont go off.
View 14 RepliesFord Ranger / B-Series :: 1991 - Tranny Slipping / Swap Options?
1991 Ranger 4.0L A4LD... Its a 4x4. ext cab
What else will bolt up to this 4.0L? Could i put a 4R44E/4R55E tranny? Is there a good stick that bolts up?
Ford Ranger / B-Series :: 1991 - Bad Head Gasket - Leaking And Coolant In Oil
I have a 91 Ranger V6 4WD with 150K that has been sitting for 7 years. The last time I drove it (7 years ago) to a mechanic, who diagnosed it with a bad head gasket - leaking coolant and coolant in the oil.
What am I looking at as far as a project: besides redoing the head gasket, what else will I most likely need to do given that its been sitting 7 years?
Ford Ranger / B-Series :: 1991 - How To Time Idles High At Start
I now have a 1991 ranger 3.0 super cab. I need a step by step walkthrough of how to time it. Keep in mind that I ha the distributor out while turning the engine over so I need from start to finish, including the spout connector. It runs right now but idles high at the start and the. Stumbles down to about 500rpm and sometimes dies....
View 12 RepliesFord Ranger / B-Series :: 1991 Truck Refuses To Start Under 45 Degrees
I have a 91 Ranger 4cyl. Tune up about 2 months ago. Mileage about 178,000. When the temperature gets below about 45 degrees, the truck will not start. It cranks like the battery has plenty of juice but refuses to start. Once the temp warms up, the truck will start first crank.
View 5 RepliesFord Ranger / B-Series :: 1991 - Rattle Sound Coming From Transfer Case
My '91 Ranger 4X4 has developed an odd rattle that sounds like it's coming from the transfer case. It seems to be pretty much the same whether the truck is stopped or moving, or in Park or Reverse, or in 2wd or 4wd or Low Range. I hear it when the engine is just idling, with the transmission in Park and the parking brake on. It seems to be getting louder. I have the 4L V-6 with auto transmission.
View 2 Replies