Ford Ranger / B-Series :: 1996 - Ignition Lock Cylinder Won't Reinstall
My keys got stolen from my ignition (battery had died because key was left in ACC and I assume the attempted car jack ended in a key theft for some reason.)
The Ranger is 96, tilt steering with plastic shrouding and column shift A/T... I followed the procedure recommended for exchanging the cylinder without the keys:
-drilled retaining pin
-drilled key slot
-manually removed parts with needle nose
-cleaned, greased and went to reinstall.....
I discovered the small metal washer between the green plastic washer and the gear was broken in half because I nicked it with the end of the drill bit. I inspected this and from what I can tell it looks like the green plastic washer is designed to hold onto the metal washer, the two of them together, from what I gather are designed to keep the gear from moving sideways or tilting. I figured that the washer should do it's job even in two pieces if I could get it in there straight and get the green washer to grab it.
Anyway I stuck it all back in there, slid the new lock cylinder in in run position, and nothing good happened. It's in the whole way, I can see the retaining pin centered in the whole from underneath, but when I try to seat the retaining pin it won't budge. I tried to align the parts at a million different angles and I just have no luck. I am planning on replacing the little metal washer, but I don't feel like it being broken alone is enough to keep all parts from functioning properly. I am stumped because I did the procedure step for step and there is nothing else apparently broken or damaged. The only other factor is that the steering wheel is locked and that sometimes made the other cylinder hard to turn, but it freed up usually with a little wiggling, this cylinder won't budge.
Ford Ranger / B-Series :: Removing Manual Door Lock Cylinder
I recently bought a 1994 Ford Ranger, XLT 4 cylinder supercab. They lost the door keys when they replaced the ignition because they never locked their doors. I bought new lock cylinders with keys and set out for an adventure. Removing the metal clamp that holds the cylinder in place was actually easier than I thought. It's that darn plastic piece connecting the cylinder to the rod for the lock system that will not break or come off. Here's the best picture I could find real quick. How do you get that vile piece of 20 year old plastic off? It's in a difficult place to get tools in there, and I can't seem to get leverage with a small screwdriver anywhere. What tips and tricks do y'all have?
View 1 RepliesFord Ranger / B-Series :: 1988 - Press Key Lock To Remove Key - Disable Key Lock?
On my '88 Ranger, there is the key lock that needs to be pressed to remove the key. When I changed the ignition cylinder, I darn near went ahead and removed it. I though I better check here first, and see if I was going to disable some other function I don't know about.
View 1 RepliesPassat (B5) :: 2003 - How To Remove And Replace A Busted Lock Cylinder
How to remove and replace a busted lock cylinder. My wife's car got broken into and used something that punched in the driver's door lock cylinder. VW wants top replace a new lock cylinder. I've been able to remove the drivers door panel but I wasn't able to figure out the final steps.
View 1 RepliesFord Ranger / B-Series :: 1993 - Cat For PA State Emission?
I am starting to work on my 93 ranger when funds are there. But my question is do i need a Cat. for PA state emissions? I have heard you do but then I hear you don't. I have also heard a few things on the fuel millage and power.... Looking for some info on this because I am not trying to cut it off and have to go back and fix it again... I want to do it once and be done with that part!
View 3 RepliesFord Ranger / B-Series :: 1993 - Won't Go Past 35 MPH And Shakes?
Today on my way to work my 1993 ford ranger would shift fine but would refuse to go over 35mph and shook pretty bad. I don't know where to start...
View 6 RepliesFord Ranger / B-Series :: 1993 2.3L 5 Speed Won't Go Into Gear
Not only will it not go into gear, truck will not start unless clutch is to the floor, and in neutral (it's only possible place) if you pick the pedal up 1/4 inch off the floor the odometer starts spinning around 1 mile in 5 seconds.... if you lift it any more it kills the engine like you shut it off with the key.... odometer reads 99,004 miles now (the last 2 are mine) I bought this truck like this ....
View 3 RepliesFord Ranger / B-Series :: 1998 - How Hard Is It To Replace A Clutch
I think the time is near for a new clutch in my 98 Ranger, 2wd/ 5 spd. How tough of a job is this? I've changed the one in my 66 Mustang years ago but things were less complicated then.
View 3 RepliesFord Ranger / B-Series :: 1993 / 3.0L V6 - Belt Squeaking Very Loudly
I have a ranger as said in title. No a/c. I noticed my belt was cracked very badly so I bought a new one. Dayco made for Ford and Mazda 3.0L V6. Looked the same length as the old one so I put it on and all was good. Then about 2 days later it started squeaking very loudly, not all the time, just 1500 rpm and higher. The hotter the motor got (not overheating just to running temp) the higher rpm it took for it to squeak. I put a stethoscope on all the pulleys/pumps and alt. It sounded the strongest on the idler.
So I replaced the idler and bearing (which the bearing was bad, but not the source of sound) it wasn't that. So I thought I'd give the belt a couple days, maybe it was too tight causing a bearing to get too tight and squeak. And the more I drove it the louder it got with less rpm needed to make it squeak. So I tried belt dressing, and still no fix. So today I put the old belt back on to see if that was the issue. Sure enough, it started up and squeaked just the same, but I tried the belt dressing on the old belt and it went silent, even at 3000 rpm. So I assume from this the new belt was a smidge too big. Right?
Ford Ranger / B-Series :: 1993 - Wiper Motor Removal?
How do you remove this clip holding the wiper linkage to the back of the motor? I can't see what kind of clip it is to know how to remove it. Ford says to remove the wiper pivot and let it drop. Is that necessary? I can't barely get to the back of the motor so I'm having to feel the clip and remove it but since I don't even know what kind of clip it is it makes it so much harder. Does the cowl cover not come off or is it just this access panel?
View 3 RepliesFord Ranger / B-Series :: 1993 - Front Sway Bar End Links?
I'm new to the whole Ranger truck thing since buying a 1993 Ranger 4x4 for my 14 y/o son. It has a 4 inch suspension lift and a 3 inch body lift running 33x10.5x15 tires. The front sway bar is not hooked up. I know that i will need drop brackets for the sway bar but my question is about the end links needed for this truck. There are 2 tabs with provisions for a horizontal bolt on each side of the twin I-beam where the end link would attach and the sway bar has a single horizontal hole on each end. Searching for replacement links at various auto parts websites only seems to yield the standard end links that consist of a straight bolt with a nut on each end and the rubber insulators. That clearly is not the correct end link for my application. Not sure if the front suspension is the factory installed unit or if it was swapped some time in the part.
View 4 RepliesFord Ranger / B-Series :: 1993 - Modulator Valve Location?
Where the modulater valve is on my A4LD tranny. I have a 93' ranger XLT extra cab 2wd with 4.0 engine. I have looked all over the tranny and thought it would be somewhere I could see it. I know I had one on my old full size Ford truck with C6.
View 7 RepliesFord Ranger / B-Series :: 1993 - Location Of The Fill Plug?
Where is the location of the fill plug for a 93 Ranger transfer case? The damper is off and I see the drain plug. Is the fill plug behind the electric motor that shifts the case? I can see what may be a plug there that looks plastic with a very small hex head in the center of it. Is that it?
Also, my Haynes manual says to use Mercon ATF in the transfer case. I see where Valvoline has a Mercon equivalent. What do ATF brand people here recommend?
Ford Ranger / B-Series :: 1998 - Replace Blend Door Actuator?
I purchased a 6.7 Diesel 2014 F250 Super Duty Crew Cab about 3 months ago. Yesterday I started my truck using the remote starter from inside my house. Seconds after I heard a loud noise. Looked outside, saw nothing and thought nothing of it till I went to open my door and realized that the driver door window shattered! I live in a quiet area, it wasn't a rock thrown at my truck or anything like that, it just Blew!!!!
I'm wondering if the truck might have some sort of pressure or torque if you wish on that window to make it just pop! My mirrors were folded in however I can't see that playing a role......
Ford Ranger / B-Series :: 1993 - 4x4 Not Engaging / Grind Just For A Quick Sec When Shifting
So went today and bought a 1993 ranger 4x4 ext cab 4.0! Runs good some bad handy work that i need to fix but truck has plenty of power and good handling...
issue 1- 4x4 not engaging. the light by the push buttons does not come on and you dont hear the "clicking" of the relay trying to engage. so whats the problem and how do i fix it?
issue 2- when clutch is fully depressed and you go to shift (this is only sometimes) you can feel and hear it grind just for a quick sec. and forget about down shifting you cant do that without slowing down. so maybe new clutch?
issue 3- at 65 the vehicle does shake a little otherwise but pretty smooth. any tips on how to smooth it out? maybe new ball joints? tighten some stuff up maybe?
Ford Ranger / B-Series :: Door Swap From 1992 To 1993 Model
Will a driver door from a 92 ford ranger fit a 93 ford ranger?
View 5 RepliesFord Ranger / B-Series :: 1993 - Cruise Will Not Disengage With Brake Pedal
1993 Ranger XLT 4.0 AT. Initially replaced ECM for other problems and then noticed Cruise w/n disengage when brake depressed unless pedal is pushed several times and with more pressure. Put in another ECM and have same problem. Have replaced the brake switch and lights come on as they should. When pedal is pushed the vacuum dump valve on the pedal will dump the vacuum to the servo but when you release the brake pedal the cruise control kicks back in and speeds truck back to set speed.
So this tells me that the dump valve is only a fail-safe feature for when pedal is depressed and does not actually deactivate the servo. Everything else with the cruise works fine: On/Off switch, Set/Accelerate, Resume, Coast. How to proceed next? Like where to find speed control module and how to test it? How to check servo to see if it is getting or dropping voltage that will electrically disengage it, etc? Don't want just throw parts at it. The new ECU's that I used came from ECU Exchange in Florida and there still remains the possibility that they are still the problem.
Ford Ranger / B-Series :: 1993 Manual Trans / Hard To Shift Into First
I'm having a little issue with shifting into first. Once in a while it simply will not go in, like you're pushing the shifter against a brick wall. If I turn off the truck and turn it back on, it works absolutely fine. I can shift into 2nd-5th no problem at all times. Is it just the shift linkage, or...? I'm not really sure where to start.
View 7 RepliesFord Ranger / B-Series :: 1993 - Clutch Release Bearing Install
93 Ranger, 4.0 liter, 4WD.....
Putting in a new clutch and clutch release bearing, and am wondering if I need to put the retaining ring in that came with the new clutch release bearing? When I took off the old release bearing, a ring did come off from somewhere, but I did not see where it was because it was so dirty.
The reason I ask is because my Haynes manual did not even mention a ring, so I was surprised to see one come off. And my manual does not say to reinstall the ring when installing the release bearing. I did get a newer Haynes manual at the library and looked through a bunch of Chilton, etc manuals.
The newer Haynes manual says to remove the retaining ring on 97 and newer models, but says nothing about putting it back in when reinstalling. So, I am not certain if I need to put a new retaining ring in with the new release bearing.