Ford Ranger / B-Series :: 1988 - Press Key Lock To Remove Key - Disable Key Lock?
On my '88 Ranger, there is the key lock that needs to be pressed to remove the key. When I changed the ignition cylinder, I darn near went ahead and removed it. I though I better check here first, and see if I was going to disable some other function I don't know about.
View 1 RepliesFord Ranger / B-Series :: 2003 - Shake After Start Up For 10 To 30 Seconds - Converter Leaking Out?
I have a 2003 Ranger 4x4 with the 5speed automatic. It has 215,000 miles on it and I don't drive it regularly anymore. Lately, I've noticed that it will shake after start up for 10-30 seconds. This only happens after it has sit for a few days or a week. After it warms up, I can drive it and stop and start it again and it has works as usual.
Is there some way the convertor is leaking out fluid and it shakes until the convertor is full again? Or is something else the problem. I've changed the fluid two or three times during the life of the vehicle.
Ford Ranger / B-Series :: 1994 - Rough Idle / Stalling - Catalytic Converter Glowing Red
94 Ford Ranger 2.3L
I started to have a slightly rough idle a while back, but not severe. I figured she was just aging a bit.
Changed plugs. Check engine light came on. Changed plug wires. Then I had a couple of episodes where it started to lose power and idle really rough (stalling). Both times it stopped after a few minutes. Had code read- they said it was coils. Replaced ignition coils. Check engine light still on, but it went a few weeks without power loss.
Tonight the loss of power returned and didn't leave, and I had a glowing red catalytic converter after I limped home 20 miles (hope I didn't do any serious damage, I was stranded.)
Found this post : [URL] .... But there's no resolution.
So, I'm probably dealing with a misfire, and I'm sure I torched my cat after tonight. So any other easy diagnose/fixes for a misfire? I'm a shade tree mechanic- so I know just enough to get myself in trouble. If I can't get a resolution soon it will be off to the mechanic (which, maybe I should have done 1st...)
Ford Ranger / B-Series :: 1994 - Rear Brake Lock Up?
Under mild-heavy braking, the rear brakes on my ranger lock up... EVERYTIME. Not just when its wet, or humid. Everytime I hit the brakes hard they lock. I think I'm getting little, to no pressure to the front brakes either. Could it be just a Proportioning valve?
Truck is a 94' 4.0l V6, RCLB, Auto, 4X4.
Ford Ranger / B-Series :: 1990 - TC Lockup Was Working Now Won't Lock
Just picked up a 90 Ranger last night, 4.0 EC, good ole A4LD, from a recipt I found has 70K or so on rebuild, was driving it today and the TC unlocked, and now it won't lock back up. I checked fluid and it was a little low, topped it off and drove it, and it was the same thing. I'm kinda new to thease A4LDs I know they can have issues, but can be good too. Just want to know whats going on so I can fix it! No codes were found when I scanned it. Trans otherwise shifts fine, you can feel it go into OD but no lockup.
View 13 RepliesFord Ranger / B-Series :: 1998 4x4 Front Hubs Will Not Lock In
I have a 98 ranger4x4 front hubs will not lock in. replaced vac lines that were rotten still will not lock,checked vacuum at solenoid had vac for a min or so then it stopped, ran vac strait to main vac line for continuous vac and they still will not lock in, had 4 wheel just the other day. What can I check or do besides set it on fire.
View 1 RepliesFord Ranger / B-Series :: 1993 - How To Replace Key Lock Cylinder
I am trying to replace the key lock cylinder (where you insert your key to start the truck) in my 93 Ranger. Using the Haynes manual, I have removed the steering wheel cover (I don't have airbags), pulled the steering wheel, removed the 3 plastic decorative shrouds and looked at a naked steering column assembly. The manual says there is a 1/8" hole on the bottom of the steering assembly where you can push up the actuator pin to release the lock cylinder assembly.
I looked and looked (even with a flashlight) and could not find a hole. I looked at the new key lock cylinder assembly and found the little actuator pin so I sorta know where the pin would be in the installed assembly. The entire key lock assembly is enshrouded (is that a word?) in the cast aluminum steering assembly.
There was a small metal plate - but that plate is just for access of the release of the steering wheel lock actuator (so I carefully bent it back!!). I know all this is for theft protection, but the truck is co safe I can't even replace the lock assembly.
Ford Ranger / B-Series :: 1996 - Ignition Lock Cylinder Won't Reinstall
My keys got stolen from my ignition (battery had died because key was left in ACC and I assume the attempted car jack ended in a key theft for some reason.)
The Ranger is 96, tilt steering with plastic shrouding and column shift A/T... I followed the procedure recommended for exchanging the cylinder without the keys:
-drilled retaining pin
-drilled key slot
-manually removed parts with needle nose
-cleaned, greased and went to reinstall.....
I discovered the small metal washer between the green plastic washer and the gear was broken in half because I nicked it with the end of the drill bit. I inspected this and from what I can tell it looks like the green plastic washer is designed to hold onto the metal washer, the two of them together, from what I gather are designed to keep the gear from moving sideways or tilting. I figured that the washer should do it's job even in two pieces if I could get it in there straight and get the green washer to grab it.
Anyway I stuck it all back in there, slid the new lock cylinder in in run position, and nothing good happened. It's in the whole way, I can see the retaining pin centered in the whole from underneath, but when I try to seat the retaining pin it won't budge. I tried to align the parts at a million different angles and I just have no luck. I am planning on replacing the little metal washer, but I don't feel like it being broken alone is enough to keep all parts from functioning properly. I am stumped because I did the procedure step for step and there is nothing else apparently broken or damaged. The only other factor is that the steering wheel is locked and that sometimes made the other cylinder hard to turn, but it freed up usually with a little wiggling, this cylinder won't budge.
Ford Ranger / B-Series :: Removing Manual Door Lock Cylinder
I recently bought a 1994 Ford Ranger, XLT 4 cylinder supercab. They lost the door keys when they replaced the ignition because they never locked their doors. I bought new lock cylinders with keys and set out for an adventure. Removing the metal clamp that holds the cylinder in place was actually easier than I thought. It's that darn plastic piece connecting the cylinder to the rod for the lock system that will not break or come off. Here's the best picture I could find real quick. How do you get that vile piece of 20 year old plastic off? It's in a difficult place to get tools in there, and I can't seem to get leverage with a small screwdriver anywhere. What tips and tricks do y'all have?
View 1 RepliesFord Ranger / B-Series :: 1991 - Location Of Door Lock Wire Loom?
It looks like my door lock wire looms go under the hood but I haven't had any luck finding them. Install an alarm with negative 500Ma pulse to operate them ? I have relays but am also wondering if the truck has its own somewhere that I can piggyback onto. I know the colors are Pink with a yellow stripe and Pink with a light green stripe.
View 7 RepliesFord Ranger / B-Series :: 2007 - Traction Lock Differential Making Noises
My 2007 3.0L XLT 2WD Ranger with 7.5" traction-lock differential started making expensive noises last weekend coming from the rear end. Shop has not yet opened up the differential because the initial though was just do a swap.
Turns out that 7.5" LS is hard to find, plenty of open diffs available. So I suggested that I'd rather swap in an 8.8" LS rear end anyway but turns out that these are also hard to find. Was a LS rear end option just not very common? or do these get scooped up just as fast as they become available?
Ford Ranger / B-Series :: Steering Wheel Lock Damaged - Popping Noise When Turning
While in the locked position, the steering wheel was purposely jerked hard to disable the mechanism on a 1996 Ranger. Now the truck will not steer easily or smoothly and a popping noise is evident when turning. I'm not concerned about having the wheel lock, but would like to be able to return driveability to normal.
The same guy who caused this damage also damaged the ignition. No key is needed to turn the switch now.
I'm lost as to how the steering locking mechanism works and wondering if I need to tear apart the column or if maybe there is a locking pin accessible that needs to be removed to regain driveability.
Ford - Explorer :: 5r55e - No Torque Converter Lock Up
I drive a 1997 Ford Explorer XLT 4X4 with 180,000 miles. A couple months ago my O/D light started flashing. When ever the code flashed i would pull over and I would take the negative cable off to get the codes to clear. While driving it, it would shift normally in till i go to about 40 mph. Then the light would come on and the torque converter would refuse to lock up. I would be in 4th gear at high rpms and when i came to a stop there would be a hard 2-1 shift. I tried solving this by changing the fluid and filter twice. I also replaced the valve body gasket and tcc solenoid. This solved nothing and it continued to do the same thing as before.
I then took it to 2 shops. One told me they go the code for the torque converter and that i would need to replace the whole tranny. The next place told me some internal pump was failing and that a rebuild was recommended. After this I continued to drive it knowing there was no point in trying to save the original tranny. My dads best friend owns a shop about an hour away and said he would replace it with a used one for free. All i had to do is pay for parts. Then one day while driving the transmission blew up and i lost all my gears. Then it was taken to my dads best friends shop. While it was there he replaced it with a used one along with a couple other parts like the starter.
After the used tranny was put in the same problems still kept happening. They tried clearing the code having no luck. I eventually picked it up my self and took it back home to deal with. I can now get the torque converter to lock up but it doesn't want to till I am going over 50mph and at high rpms. The light still comes on when i get to about 40 mphs. I tried clearing the PCM and that fixed nothing. Then i tried replacing the thermostat( It was bad anyways) thinking that the thermostat was not sending the right info to the pcm to make the torque converter lock. Now im completely stuck. What could be causing the problem. I know there are a ton of external sensors that control the torque converter lock up.
Ford Super Duty (1999-2016) :: 2002 - Torque Converter Slip / Stall - No Lock Up
I have a 2002 7.3 with the 4r100 173k miles. If your nice to it she drives fine, but if you get on it the torque converter will slip/stall kinda revs up like 300 rpm then slams really hard between 1st and 2nd. Other gears work fine. I've only had it not happen like 10 times since I've owned the truck ..... I don't really beat on it except for towing which I'm starting to do a lot of. Wondering if putting a new stock torque converter in it is worth it.? Not gona blow the bank on a TC unless I'm putting a brand new trans in the truck. Which I don't think it needs in the near future.
View 14 RepliesSilverado :: Torque Converter Will Not Lock Up
I have just had my transmission rebuilt and torque converter replaced. Now the torque converter will not lock up. It turns 2700rpms @ 55 mph! The shop says it maybe my speedometer causing this because it is stuck at 20 mph. was this way before it went into the shop. I'm replacing the stepper motors next week when the parts get here.
View 14 RepliesFord - Ranger :: Rear Wheels Lock While Driving
After a transmission flush, my husband's Ford Ranger rear wheels have locked when backing out of the garage; pulling out of a parking spot; and driving down a hill.
He had checked the transmission fluid level, and it was a little high. The shop drained it down to where it should be, said the fluid was discolored, and sent him on his way. But it has happened again since then.
Ford - Ranger :: 2000 - Anti-lock Braking System Is Not Working Properly?
My 2000 Ford Ranger 4x4 truck's anti-lock braking system is not working properly. When I slow down for a stop my anti-lock brakes kick in every time for about 1 or 2 seconds. What can I do to stop this from happening.
View 2 RepliesFord - Ranger :: 1994 - New Ignition Key Lock Cylinder / Steering Wheel Not In Locked Position
I easily removed the key lock cylinder but when I went to put the new one in I cannot get it to turn all the way back to lock the pin in place. The steering wheel is not in the locked position nor can I get it to lock. I have turned the steering wheel as far left and right as I could go with no success on getting it to lock or on getting the ignition key lock cylinder to turn back securing the actuator pin. The old key lock cylinder won't go back in either. What am I doing wrong?
View 3 RepliesFord Ranger / B-Series :: CEL On After Oil Change?
I just changed my Oil, added a FRAM filter and bought some good Quakerstate High Mileage and my truck runs good. However, I noticed that my Check Oil light is constantly on. I also recently changed my Oil Sender, and I wonder if that has got something to do with it.
View 3 Replies