Ford Fuel System :: Runs Great For A While Then Starts To Get Air In Fuel Line
I have a '77 F250 with a 460. (Under edit) It has a holley 750 carb. (under 2 years old). It ran fine for about 2 years and now all the sudden it seems to not get enough fuel. I have a clear fuel filter on it and you can see that it is full of fuel when I first start it up. Just letting it sit there and idle after about 5 minutes it starts to show air coming through the lines and it gets worst the longer it runs.
If I take it out on the road and drive 55 it will be about 1 or 2 miles and it acts like it's not getting fuel. I stop and open the hood and check the filter and it is empty. What could cause this? I took it to an old Ford machanic and he has checked the fuel pump, fuel lines, sending unit, and gas tank. He is at a loss. I am no mechanic, but I am mechanicly inclined. I can't see it would be that hard to figure out. What do I do?
Ford Fuel System :: Engine Runs For 10 Seconds Then Dies
I have an 84 Bronco II with a fuel injected 302 in it. I was out wheeling with it the other day, and it was doing great until about 3:00. I got out to see that my brothers radiator had sprung a leak. When I got back in my Bronco and put it in gear, it just stalled. I started it back up and it ran for about 10 seconds then shut off. It kept doing that over and over again. Finally, I got tired of it and had someone get my truck and tow me out of there. Why would it run for about 10-15 seconds only and then shut off like it was getting no fuel (yes, it does have fuel in it)? I have a feeling it might be fuel pressure regulator valve because it was acting up a while ago..
View 10 RepliesFord Fuel System :: 1989 F250 Fuel Pressure Drop Quickly Under Heavy Load
I am a newbie as far as fuel injection. The original issue the truck had was no fuel. I tracked down the issues to a blown fuel pump relay and a melted inertia switch. I jumped the inertia wires with a new fuel pump relay installed and the truck ran at an idle and up to 3500 RPM when stationary. If the truck is going up a grade or needs more throttle it will start to lose fuel pressure and end up stalling. I had the fuel pressure gauge connected to the schrader valve on the fuel rail and had 30-35 PSI when idling. It runs good under light load on the throttle.
Under heavy load it starts to drop quickly and if you back off the throttle it will stay running some times. I changed the fuel filter and also replaced the high pressure pump on the main frame and it still has the same problems.The original pump was pumping about 13 ounces of fuel in the 20 second test that the repair manual suggested. I have even placed a jumper wire direct to the new fuel pump to bypass original wiring and possible problems. When it stalls under load (No Fuel pressure) at the schrader valve you can hear the fuel pump running but there is no fuel pressure.
If I turn off the ignition for a few minutes and then turn the key back to the on position it will start to pressurize and then start and run at an idle. I even replace the ignition switch as it was a little temperamental. I have not changed or checked the fuel pressure regulator as it is a pain to get to at the back of the engine. I do not want to spend a fortune tracking down this problem since the truck may not even pass its smog inspection and may be a parts truck only.
67 F-250 4x4
73 Crew 4x2 (4x4 Soon)
89 F-250 Super Cab 4x4
Ford Ranger / B-Series :: 1994 - Idles Rough / Stalls When Cold But Runs Great When Warm
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 RepliesFord Ranger / B-Series :: 1989 V6 Stalls / Dies / Powerless After Warm Up
I've recently acquired a 1989 ford ranger xlt 2.9L V6 and iv got my elbows deep already..... starts right up and scene its an older truck i let it warm up for a few minutes seems to sound alright so i jump in and take off... well i make it about two blocks and as soon as the truck seems to warm up it starts to sputter and die out... starts back up and idles for a min and i try to take off, but it seems to have NO power and jerks and dies.... so i push to a street parking spot and get situalated start the truck up again and take off only to make it about half a block tell it does the same....
First i think iv run outta gas witch i might of not sure so I walk to station and get three gallons. put in truck and same is happening. so i start kicking myself for not haven any tools with me and i leave tell next day... that night do a little research and get some idea's of what could be the problem'(s) so i start out with things that look like they need tending Badly WIRES, PLUGS, ROTOR, CAP, MAP SENSOR, and now after a whole day in the rain (Northwest BTW) and grease to elbows? 2.9 V6? What step's should i take next?
Ford Fuel System :: 1989 F150 - Hot 28 Psi Fuel Pressure Shuts Off?
for the past week we have been trying to figure out what is wrong with our truck. We recently bought it and it ran fine. Then got in a minor accident just a fender bender and it started acting up so I got towed to garage. First it would run when cold, but when hot fuel pressure would drop to 28 psi.
So I put new fuel pump, it started but still did the same thing hot 28 psi fuel pressure shuts off. So I put regulator on it, then had 0 fuel pressure won't even start. So got a another regulator thinking I got a bad one, still 0. Checked relay, there fine. I'm gonna check lines and see where fuel stops at but everything is new on it.
Ford Fuel System :: 1987 F150 Fuel Pump Runs After Key Is Off?
Why the frame mounted fuel pump might run after the key is turned off? Then when you turn the key on it may or not run. If it does run it keeps running. shouldn't this shut off after pressurizing the line? is their a pressure switch in the pump that's failing? This has the 3 pump system...
View 4 RepliesFord Fuel System :: Fuel Pump Runs Constantly
It started out w/ my wife swapping from the front fuel tank to the rear tank due to the fuel qty getting real low. Then the next day when I drove it I had bad fuel qty and amp meter indication, I found a blown fuse on my fuel qty/amp meter gauges. I replaced the fuse and got my indications back. Now I hear my front tank fuel pump is running constantly when selected to its position. Its now full of gas and still runs constantly. The rear tank/pump operates normal. I am wondering if I ran that pump empty and lost its prime? What is the best way to burp it?
View 9 RepliesFord Fuel System :: Small Leak Where Filler Neck Ties Into Rubber Hose That Runs Into Fuel Tank
I recently purchased a used 1999 F250 Super Duty with about 150k miles on it. The truck runs great and I have no complaints but there are a few things that need to be taken care of. It looks like there is a very small fuel leak where the filler neck ties into the rubber hose that runs into the fuel tank. There is a thin film of diesel along the side of the tank, on the leaf spring, the air bag and various other places. Nothing is dripping. I want to drop the tank and replace the hose. The Haynes manual says to depressurize the whole fuel system--is this really necessary if I don't plan on doing anything to the system aside from dropping the tank?
View 2 RepliesFord 6.0L Power Stroke Diesel :: On Cold Start Acts Like Runs Out Of Fuel And Dies
I've got a cold start problem. Turn it on, wait until glow plug light goes off, hit the starter and it fires right up. It acts like it runs out of fuel and dies. Hit the starter and it fires up and dies again. Third time it stays running. It's not a long crank either. 1-2 seconds at most. Fuel pressure is 59, HPOP immediately goes 1000+, everything looks good. It will start fine the rest of the day until it sits overnight. This is an early 04.
View 14 RepliesFord Super Duty (1999-2016) :: 2004 F250 V10 Runs Rough When Warm
2004 F250 V10, runs good until it warms up whether it's hot or cold outside. While on freeway, it really shakes while cruising, but of you get in the gas enough for a kick down, seems to be pretty smooth. I've changed the coils, and 9 plugs (one wouldn't budge, but the others I took out looked fine) to no effect. Where else should I look? Also, no CEL, and no codes, which seems odd as bad as it feels...
View 11 RepliesFord Aerostar :: 1993 - Runs Great Except When Warmed Up
My Aerostar is a 93 extended EB with 4.0, AT, 212k mostly reliable miles, and blue and gold paint that has held up remarkably well. When started it runs great; smooth idle, easy revs, normal as can be. But when that third pip on the digital temp gauge hits Normal the van becomes possessed. The idle will randomly drop or surge or return to normal, the check engine light will come on for a few seconds then go off, all without pattern, just kinda crazy. Today I held it at 2k rpm, then it bogged down to like 800 rpm and lit the CEL, then it returned to 2k rpm and the light cleared, swung up to 2.5k, all while I hold the throttle steady. The light does not always come on when it bogs. I see no black smoke from the exhaust and it smells normal, but it was kinda windy today.
The check engine light is not lit otherwise so I assume no hard codes are stored. I think I found the code retrieval process for the OBDI but I have not done that yet. After reading a bit in this forum I thought to clean the MAP sensor, but I do not have security torx bits to remove it yet. As background a few years ago it had an oil leak from the top rear which I ignored, and it slowly rotted a harness back there till one day the harness died leaving me running on 3 cylinders. My local Speedy Lube guy was ex Ford dealership and knew Aerostars, he did the diagnosis and repair and said it was a common problem. But he has moved on. I was also told I have a torn boot on a plug wire, but there's no way to get my ham-like paws back in there, from front or back, to verify or replace. I mention all this as background, I doubt a bad plug wire is the issue here.
It seems like an odd problem to me because the only pattern is related to operating temp. It is not a constant problem, not an intermittent glitch, but it very definitely goes nuts right when it achieves normal temp. Aside from pulling the codes, which I will figure out tomorrow, any other tests I can run to diagnosis? Any way I can trick this thing into thinking it is cold all the time?
Ford 6.0L Power Stroke Diesel :: DTC P0381 - No WTS Light But Starts And Runs Great?
My 03 F250 6.0L Starts and Runs fine but will never illuminate the glow plug/ wait to start light? Scan tool test on GPRM and tells me everthing is OK. Cleared all codes, turn on key, no WTS light and throws P0381 DTC every time. What my problem is?
View 4 RepliesFord Fuel System :: 1977 - After Rebuild Runs Rough - Mixture?
I just had a former Ford tech rebuild my motorcraft 2150 2v on my '77 F250. I took it home, put it back on the truck and it ran kind of rough. I then went ahead and screwed both idle mix screws in untill seated, then back out two turns. The truck ran great, turned off truck then when it the house for dinner. Half an hour later I come back out...truck will not start, just sits and cranks. Finally got it started and it ran good, but crapped out after it warmed up. I have made sure there were no vac leaks when truck was running the first time. Did I adjust the mixture right?
The truck is a '77 F250 400/C6
Ford Fuel System :: Starts But Dies Instantly
Ok I finally got my truck to start, but it dies instantly. I had a friend of mine who is a mechanic look at it and he said gas wasn't filling up the front bowl, but gas was pumping? Could something have happened when the carb was rebuilt?
View 3 RepliesFord Fuel System :: Idles But Dies When Throttle Applied?
I just rebuilt the Autolite 4100 on the 390 in the 62 T-Bird I just purchased. Starts up and idles great, but when I apply slight throttle, the motor shuts off. If I apply a lot of throttle quickly, it picks up fine and drives with no problems. No sputtering, or backfiring. I just slightly apply the throttle, the RPMs drop, and the motor cuts out completely. Starts right back up when I turn the key, but does the same thing, at any temp.
I originally thought it was a vacuum leak, but checked what few vacuum lines there were, with no leaks to be found. Hooked up my vacuum gauge and it read at a steady 15psi.
New mechanical fuel pump, haven't checked the fuel pressure yet, but I installed a see through inline filter, and it's filled up and pumps fine.
Timing is at 8 degrees, and vacuum advance is hooked up to the only vacuum line in the carb. New cap, rotor, plugs and wires.
I adjusted the idle mixture screws down until the idle dropped, then turned them out a half turn (I've read on here it should only be a 1/4 turn, so I'll adjust that later today). When I was messing with the carb yesterday, I noticed the inlet check ball retaining screw was leaking a bit of fuel, so I went over the carb and checked all the screws and tightened down what needed it.
When I rebuilt the carb, I left the original needle & seat assembly, since they were in great shape, and the ones in the rebuild kit were much smaller. The choke plate needs to be adjusted, as it doesn't open up all the way at full temp, but the engine did the same thing with the plate held open all the way open.
I've gone through everything else I think it could be, so I'm figuring it's the carb. This is my second carb rebuild ever (first was a Motorcraft 2150) and it went smoothly, and I double checked the floats and measurements.
Ford Fuel System :: Dies When Putting In Gear And Giving Gas?
Outside of lawnmowers, this is my first carbureted engine. I have always fixed stuff that broke on the vehicles I've owned, and done some difficult (for me) task such as replacing a timing belt on a honda, and mcpherson strutts and a head gasket on a 4 cylinder SAAB.
I'm the new owner of a '68 F100 that was originally a 3 on the tree inline six. It's been converted to an FE390 with an automatic transmission (C6 I believe). It has an edelbrock 1411 (750CFM). I've recently got it running at idle of it's own gas tank. This is the list of work I've performed since getting it.
Replaced:
old gas
old oil
brake master cylinder
old dot3
plugs and wires
I also added 3-4 quarts of F-type tranny fluid.
Related to the Carb all i've done is removed it and dumped some carb cleaner in the bowls.
The Problem is:
Car starts and idles fine. When I drop it into any gear, the engine bogs down and begins to idle much slower. If i feather the gas pedal, or punch it, the engine dies.
I'm told that the carburetor had some components replaced (springs/jets) to make it run properly, so my guess is that it is closer to a 1407 now, just with electronic choke. I'm intimidated by tearing the carb apart and attempting to rebuild it, but I'm willing to do it if that's what it will take, I'm also willing to buy a new carb to avoid 12 hours of work trying to fix the existing one, but I'm afraid I'll have tuning issues beyond my capabilities even with a new carb. Also, the truck doesn't have a tach to assist in the tuning process.
I'd love to bolt something on and start driving, but I'm guessing it won't be that easy. Is it most likely a carb problem? Any recommendations on what I should do, considering my total lack of experience with carburetors?
Ford Fuel System :: Hard To Start When Engine Is Warm
I have a recently rebuilt 400 with a mild cam and Tmeyers flat top pistons. The carb is a 600cfm edlebrock that was bought new and installed a few months ago.
The issue I'm having is if I'm driving around and shut it off to run in the store its hard to start when I come back. I end up having to floor the gas to get it to start. When it's cold I tap the gas and turn the key and she lights right off. Could this be an issue with vapor lock? Why does it go away if I floor the gas?
Only other thing going on is when accelerating the engine runs noticeably smoother above 2700rpm. It's a little boggy below that. Probably two different problems but I figured I would throw it out there.
Ford Fuel System :: 1991 F250 XLT - Fuel Pump Will Not Stop Running
I just bought another 1991 Ford. This one is a 1/2 ton XLT Lariet with the 302 and for the first time I own a short bed. I also have a 1991 F-250 XLT with a 460 and a 8' bed.
Here is the problem, ( I think) it will not run or at least not for long. The fuel pump, which I am guessing is in the rear tank will not stop running. On the F-250 the pump stops running after a few seconds after I turn on the key.
Where should I start to find out my problem with the fuel system?