Ford Fuel System :: 1977 F250 - Fuel Leak From Filter Attached To Carburetor
I have a 77 f-250 with a 460 engine and a 4bbl Motorcraft carb and its leaking a substantial amount of fuel out of the newly replaced filter that is attached to the carburetor. The fitting is tight and I even tried buying some small gaskets to seat it, but that didn't work either.
View 1 RepliesFord Fuel System :: 1977 - Engine Keep Running With Foot On Pedal?
Have a 1977 ford f150 with 351m with a motorcraft 2150. Had ( who I believe was a reliable source ) rebuild carburetor for me and after putting back on I can only keep engine running with foot on pedal. I turn idle mixture screws all way in and then proceeded to back out equally. This does not appear to be doing anything. I did turn the choke 2 notches to lean and was able to get it to idle but it wasloping so bad i shut it down and put the choke back to the middle setting.
View 13 RepliesFord Fuel System :: 1977 F250 - Spark On Throttle Linkage
I noticed last night while messing with my truck that I have a constant small spark on my throttle linkage on my carb. BTW, it's a 77F250 with a quick fuel Ethanol carb with an electronic choke. That really probably don't make a difference anyway. Is this a common thing and do I need to run a grounding wire from the carb to the rest of the engine?
View 2 RepliesFord Fuel System :: 1971 F250 - Gas Leaking - A Lot Of Crank To Start - Rebuild?
I have a 1971 F250 automatic with original stock 360 engine (100k miles). It currently has an Autolite 2100 2bbl carb.
The Autolite is leaking gas out somewhere where I can't see the leak. It takes a lot of cranking for it to start after sitting 10 minutes and my wife won't drive it for fear of being stranded. My attempt at a rebuild must have failed... Also have issues with anti-stall dashpot spring coming off while driving. When the spring and plunger come off I have to hold the gas on a little to keep from stalling while stopped at a light. A couple other parts looked like they needed repair during the rebuilt, but the kit didn't have any replacement (vacuum diaphragm torn). Also, after replacing plugs, plug wires, replacing points with Pertronix Ignitor 2, a new rotor, and distributor cap, it still doesn't hold a steady idle. In fact it is hard to get it down to the spec idle for an automatic without fear of stalling.
To make a long story short, what is a low maintenance 2bbl (new, not rebuilt) replacement carb. The truck needs to be dependably started by my wife for garage sale runs and home depot trips. I could switch to a 4 bbl intake, but would rather wait for another 50k miles and switch the engine over to a rebuild 390 with nicer intake and carb.
Ford Fuel System :: 1987 F150 Fuel Pump Runs After Key Is Off?
Why the frame mounted fuel pump might run after the key is turned off? Then when you turn the key on it may or not run. If it does run it keeps running. shouldn't this shut off after pressurizing the line? is their a pressure switch in the pump that's failing? This has the 3 pump system...
View 4 RepliesFord Fuel System :: Runs Great For A While Then Starts To Get Air In Fuel Line
I have a '77 F250 with a 460. (Under edit) It has a holley 750 carb. (under 2 years old). It ran fine for about 2 years and now all the sudden it seems to not get enough fuel. I have a clear fuel filter on it and you can see that it is full of fuel when I first start it up. Just letting it sit there and idle after about 5 minutes it starts to show air coming through the lines and it gets worst the longer it runs.
If I take it out on the road and drive 55 it will be about 1 or 2 miles and it acts like it's not getting fuel. I stop and open the hood and check the filter and it is empty. What could cause this? I took it to an old Ford machanic and he has checked the fuel pump, fuel lines, sending unit, and gas tank. He is at a loss. I am no mechanic, but I am mechanicly inclined. I can't see it would be that hard to figure out. What do I do?
Ford Fuel System :: Fuel Pump Runs Constantly
It started out w/ my wife swapping from the front fuel tank to the rear tank due to the fuel qty getting real low. Then the next day when I drove it I had bad fuel qty and amp meter indication, I found a blown fuse on my fuel qty/amp meter gauges. I replaced the fuse and got my indications back. Now I hear my front tank fuel pump is running constantly when selected to its position. Its now full of gas and still runs constantly. The rear tank/pump operates normal. I am wondering if I ran that pump empty and lost its prime? What is the best way to burp it?
View 9 RepliesFord Fuel System :: Small Leak Where Filler Neck Ties Into Rubber Hose That Runs Into Fuel Tank
I recently purchased a used 1999 F250 Super Duty with about 150k miles on it. The truck runs great and I have no complaints but there are a few things that need to be taken care of. It looks like there is a very small fuel leak where the filler neck ties into the rubber hose that runs into the fuel tank. There is a thin film of diesel along the side of the tank, on the leaf spring, the air bag and various other places. Nothing is dripping. I want to drop the tank and replace the hose. The Haynes manual says to depressurize the whole fuel system--is this really necessary if I don't plan on doing anything to the system aside from dropping the tank?
View 2 RepliesFord Fuel System :: Engine Runs For 10 Seconds Then Dies
I have an 84 Bronco II with a fuel injected 302 in it. I was out wheeling with it the other day, and it was doing great until about 3:00. I got out to see that my brothers radiator had sprung a leak. When I got back in my Bronco and put it in gear, it just stalled. I started it back up and it ran for about 10 seconds then shut off. It kept doing that over and over again. Finally, I got tired of it and had someone get my truck and tow me out of there. Why would it run for about 10-15 seconds only and then shut off like it was getting no fuel (yes, it does have fuel in it)? I have a feeling it might be fuel pressure regulator valve because it was acting up a while ago..
View 10 RepliesFord Fuel System :: 1989 F250 5.8L Runs Great Then Dies After Warm
I just purchased a 1989 F250 with a 5.8 motor. Great truck for its age. Ive owned other Ford trucks in the past and my Dad had them as a kid. Love them.
When I bought the truck from the 2nd owner it had a problem so I bought this truck with the problem figuring with my past knowledge I could fix it. Not the case. When I got the truck it would start fine and run really great but when it got warm it seems it would die and I would have to wait till it was cooled down to start back up and again it would run fine. Well the problem got worse and worse and now it wont run at all.
It will run on starter fluid so that leads me immediately to the fuel pumps. I say that plural because none of them will run it seems. I did a fuel pressure test at the shrader valve at the top of the motor on the fuel rail and I get no pressure at all when I turn the key. The relay in the engine compartment seems to be working to as I can hear it. I put a new on of those on to to be sure. Leads me back to the pumps again. I replaced the external pump on the fuel rail and I know thats working. I replaced the fuel filter to while I was there.
Is it possible to have BOTH fuel pumps in the front and rear tanks go at once? Seems unusual. My other F150 with dual tanks worked great and when the back tank pump went I could just switch it over to the front tank.
Ford - Explorer :: 2000 - Runs Rough And Egg Smell After Replacing The Fuel Pump
I have a 2000 Ford Explorer with 4.0 SOHC engine, I have had some cold start problems. I cleaned the IAC and the problem went away for a few months and then came back. Two days ago the temps got very cold and it would not start at all, I re-cleaned the IAC and still no start. I replaced the fuel pump with an aftermarket pump and engine started right away. Now I have a rough idle, bad skip and bad exhaust odor. I am still thinking IAC but I am concerned that the aftermarket fuel pump is pumping to high pressure or that I may have crimped the return line. I have driven about 30 miles hoping the computer would make adjustments, still runs rough and the check engine light has not come on.
View 12 RepliesPassat (B6) :: 2006 Check Engine Light On - P0171 Lean Air Fuel Mixture
I have had 06 passat with a 2.0 turbo. It been a great car. check engine light has come on with a few codes.
P0171 lean air fuel mixture. P2015, p2008, p0507, p2015, p2008.
Engines - Gasoline - Lights - Nissan - Sentra - Sensors :: CEL Code - Lean Air / Fuel Ratio Mixture
After my 2005 Nissan Sentra check engine light came on I had the codes read. The code is indicating that there is a lean air/fuel ratio mixture. I'm thinking this may be a false positive(bad sensor), clogged fuel injector, etc. The light has gone off and come back on. I live in Utah where the cold weather may play a factor. How to diagnose the real problem, or where I should start?
View 8 RepliesAccent LC (2000-05) :: 2001 GS Runs Rough On Full Tank / Fuel Smell In Car
I have recently purchased a 2001 Accent GS which has the 1.6L DOHC engine and have done a big road trip in it which has created a problem. When I fill the fuel tank up it runs really rough, has no power, and stalls at idle unless I keep the revs up. I can also smell petrol very strongly in the car all the time, plus it's running really rich as I can smell fuel on the exhaust and the last symptom is the loss of power down low(due to running rich).
I was on my road trip so had no tools on me and got the local mechanic of a small town to do a few basic things (change spark plugs, leads, and fuel filter) but to no avail. It runs smoothly when it gets below the full line on the fuel level gauge so I just didn't fill it up completely to get the car home but it still runs really rich and doesn't have quite as much power.
Ford Fuel System :: Idles Very Rough - Gas Smell
The carb on my 460 in my truck is acting funny. It almost sounds like a dragster It Idles really rough. I tried setting the Idle mixture screws on the side of the metering block. I bottomed them out and them turned them out 1 1/4 turns. I started turning them in till I got the highest reading on my vacuum gauge, about 13 hg. The screws are only about 1/4 turn from being bottomed out. It was running smoother, then it stalled when I restarted it, it started running really rough again.
The exhaust smells of gas. I turned the screws all the way in just to see what would happen, I thought it should stall but it didn't. I had my timing light hooked up and checked it now and then during all of this and it didn't change at all. The screws had almost no resistance to turning, shouldn't they have some resistance?
Ford - Explorer :: 2002 - Either Stalls Or Starts - Runs Rough And Then Stalls With No CEL - Water In Fuel?
We've had two problems within the last week with our 2002 Sport Trac (4.0l SOHC engine w/167,xxx miles). They may be unrelated, but I suspect there's good change they are. Both incidents happened while my 16 yo daughter was driving, so there's only very limited info on what happens. Both times, when I get there, it starts and runs fine. There is no CEL.
The first time it apparently stalled as she neared her destination after driving only about 2-3 miles at 35 mph or less after a cold start. She was slowing to pull into a parking lot and reported the dash lit up with warning lights, no power steering assist and no power brakes and no power from the engine. When I arrived it started and ran normally. She had fulled up the day before after two days of heavy rain, so I suspected water in the gas. I drove it more than 200 miles within the next 24 hours under a variety of conditions and filled up at a different station. I experienced no problem what-so-ever, and didn't bother adding any dry gas.
Then 5 days later (still on my fill-up) when she tried starting it after sitting all day, she reported the engine started but ran rough before stalling and never idled normally.
Doesn't the fact there's no CEL eliminate a lot of the upstream part of the control system......like sensors and actuators? This leaves things like the downstream parts of the fuel and ignition systems. I.e. from the fuel tank / pump to the injectors and the downstream parts of the ignition system.
What are the possible culprits? Fuel pump, fuel pressure regulator, injectors, ignition module, spark plugs, and....... what else? (I'm not that familiar with what these engines have) And of the possibilities, what are the most likely causes.
Ford Audio/Video System :: 1977 F100 - FM Working Fine But AM Works Only By Jiggling Antenna
I have a 77 ford f100 I am restoring. I have two factory am/fm radios. I bench test both with antenna male plug all the way in, and the fm works fine on both radios. The only way to get am to work, is to slide the male antenna plug all the way out till it is just touching, then if I jiggle it, the radio plays.
View 1 RepliesFord Fuel System :: Running Rough - Skipping / Surging And Die
I built the 400 in my 79 a couple years ago and it runs very well...until yesterday. I'm about 80 miles into this tank, and on my way home from work, I thought I felt a vibration (not in the steering wheel, but in the front oc the truck). Then the engine became evident it was running rough and was skipping and surging. I stopped.
It idled pretty rough, then died. Fired right back up, ran rough, and died. Sometimes it would idle smooth for several seconds (20-30) then start surging and skipping and die. I could hold a little throttle and it would run about the same, except some backfiring in the exhaust (more like a big hiccup).
The carb is a 670 Street Avenger with nothing really done to it. The bores are really black (not sooty, more damp or so). I have always used the air filter, so that's odd. I took the carb off and removed the bowls. Nothing inside has a dirty or clogged appearance at all. Not sure if I should completely rebuild it.
Datsun :: 1977 - Possible To Remove Vacuum Lines From AC System
I decided to do some work on the engine bay of my '77 Datsun 280Z. I would like to know whether it is possible to remove the vacuum lines from the system, and if so, what would be the effect on the AC system? If I understand it correctly, the AC selector and mode doors are mechanically operated and vacuum lines assist in opening (i) the air intake door and (ii) the mode door?
View 10 Replies