Santa FE SM (2001-06) :: P1192 Code - Faulty TPS Sensor
My 2003 Santa Fe 3.5 is in limp mode, you can't change the gears and showing signs of faulty tps sensor, but my mechanic is telling me to change whole electronic throttle system , May be its only the sensor.
View 1 RepliesSanta FE SM (2001-06) :: 2002 - Misfiring / Codes P0171 And P0300 Came Up
My car is misfiring, codes p0171 and p0300 come up on the code reader. It idles rough and has very little power. I have checked my exhaust , it is not plugged. When I unplug coil #2 while idling there is no change as to the engine performance so I switched the coils around with no difference when coil is unplugged on cylinder #2. I have changed the plugs, there is power to the coil, all plugs are firing and when removed plugs 2 and 3 are wet with fuel indicating I am getting fuel and fire. I have replaced the cam sensor with no change.
View 3 RepliesCabrio :: 2001 - OBD / P1128 / P0411 / P0134 / P0172 Codes Came On
So I didn't pass the smog check for the new used car that I just purchased 10 days ago. Although my old car (same model), was five years older, I never had this problem. I was told that it is a gross polluter. These are the problem that I have to fix:
OBD Fault Codes - P1128 Manufacturer specific codeP0411 Secondary Air inj Incorrect FlowP0172 System too Rich (Bank 1)P0134 O2 Sensor CKT Inactive (Bank 1 Sensor 1)
How this happens?? 2001 VW ...
Ford - Explorer :: Codes P0171 And P0174 - Lean Bank 1 And 2 Sensor 2
I have been getting a P0171 and a P0174 code lean bank 1 and 2 sensor 2. I have replaced all 4 censers the 171 is gone but I keep getting the P0174 and it only comes on when I am on the highway after driving around 10 miles or so i got a freeze frame of the data when it happen.
View 6 RepliesSanta FE SM (2001-06) :: CEL Codes For Crankshaft Position Sensor - Random Misfires
I am having a problem with my 2003 Santa Fe I have taken it to have the check engine light codes read and I have a code for the crankshaft position sensor, random misfires, something with gear 2 and 3 (not sure what it was exactly) it makes a loud noise when in 1st and 2nd gear when I shift out of 2nd the noise gets less and less until its gone and then does not come back until the car sits for a little while and cools down. Its running rough and does not have any power when accelerating. I had the timing belt changed a few weeks ago and it started running funny shortly after. I don't think the guy that did the timing belt knew what he was doing because I had to have someone go behind him and tighten the pulley.
View 3 RepliesSanta Fe (CM - 2007-12) :: Code C1209 - Faulty Right Rear Wheel Speed Sensor
My mother in laws 2012 Santa Fe had a number of dash lights on (ABS, hill decent, stability control). I put my scanner on it and came up with fault code C1209 which showed up as a faulty right rear wheel speed sensor. I have replaced this module and then cleared the codes.
However, the dash lights still light up and the vehicle continues to throw the same code. I don't work on Hyundai's very often so I am at a bit of a loss.
Santa Fe (CM - 2007-12) :: Check Engine Light Going On - Fuel System Lean Codes P0171 And P2187
My wifes 2007 Santa Fe Limited 3.3 has had a check engine light going on a year now. Car has about 122k on it now. Scanned codes about 6 months ago and had a fuel system lean code. Did some reading and ended up replacing the purge valve. The CEL stayed off til the end of the drive cycle and came right back. I have noticed when you fill the car up there is a real strong smell of gas but the car always starts right up. It now has a P0171 Fuel system too lean (b1) and P2187 Fuel system too lean at idle. Where to start. Don't have much background with hyundai. Also the ESC off light comes on randomly and goes off. Doesn't happen real frequently though.
View 4 RepliesFord - Explorer :: 2001 - Too Lean Codes P0171 And P0174
Working on my son's 2001 sport trac. 200K miles but it has always been a great running truck.
I have two CEL codes:
P0171 System too Lean (Bank 1)
P0174 System too Lean (Bank 2)
I have found several issues so far, but have yet to get rid of these pesky codes.
So far I have changed:
- Intake Gasket - I had coolant loss which replacing this gasket fixed.
- PCV Valve and Hose - valve was damaged and the hose leaked.
- EGR Valve - Valve was leaking
- Fuel Filter
- Mass Airflow Sensor
The engine does appear to be running much smoother now, but the lean codes remain.
Yaris/Scion & Vitz :: 2001 Echo Faulty ECT Sensor - Error Code P0125
I'm getting error P0125 on my 2001 Echo, which points to possibly a faulty ECT sensor.
Where is this sensor located? Seems like under the air box? Is replacing this part as annoying as it looks? And, are there any other possible causes for code P0125?
In case it's related, I will mention that code P0171 (mixture too lean, I believe) is present as well, and the car does hesitate upon initial acceleration when standing still. Once it's moving, it works fine.
Maybe it's time to start thinking about replacing this car... it has 216,000 miles...
Santa FE SM (2001-06) :: Faulty Brake Master Cylinder?
I had this sad puppy noise coming from my brakes so I have now replaced my brake booster. When doing so I took my old brake master cylinder and put it on my new brake booster. When trying to bench bleed it it only came fluid from the P marked circuit. It came no fluid from "S". I guess it stands for primary and secondary.
I thought it was because I couldn't press the piston hard enough so I installed it in the car so I could use the brake pedal to get more power. But still no fluid from "S". Is the brake master cylinder faulty? The rear discs are unevenly worn.
Ford Escape / Hybrid :: 2001 XLT V6 - Cold Start And Stutter / Codes Read P0171 And P0174
I got a 2001 Escape XLT (V6) a couple of months ago. Its in great condition, only 82k miles on it too. It had the notorious door handle issues which I have had fixed. It also had the wet weather stuttering problem, which I had fixed by having all 6 spark plugs replaced (Motorcraft OEM plugs), the back 3 coils replaced, upper intake gaskets replaced, Valve cover gasket replaced, PCV valve replaced (motorcraft).
It runs great when its warm, the problem I am having is when its cold outside and the engine is cold, it starts up fine but idles like crap and if its really cold outside, it starts and dies 3 or 4 times before it can even get to the crappy, stuttering idle. I have to intermittently feed it gas to keep the cold idle going long enough (3 or 4 minutes) before I can drive it. Once the engine is warm it drives like a champ. The only warm engine issue, is occasionally after driving it and putting it in park, the engine will rev up to 2000, 3000+ rpms, and just keep going up until I shut the engine off.
The codes read P0171 and P0174, which are lean on bank 1 and bank 2. It had also thrown a misfire on cyl 6 but once I cleared that it hasn't come back, just the lean codes are still present.
From what Ive been reading, this can be a number of issues, ranging from the IAC valve, EGR valve, MAF or the lower intake gaskets. I'm very much a rookie when it comes to car mechanics, but I think I can handle changing the IAC, EGR and MAF since they are all on top of the engine. However I don't know if I could handle the lower intake gaskets. Ironically, the gaskets are the cheapest part, but the most labor if I paid someone else to do it.
If I replace the EGR, do I also need to replace the EGR Modulator as well? Looking for brand names that are best bang for the buck when it comes to these other parts I have mentioned?
Ford Super Duty (1999-2016) :: 2008 F250 V10 - Bank 2 Sensor 2 Oxygen Sensor Is Faulty
My Bank 2 Sensor 2 oxygen sensor is faulty and I need to replace it. The guys at the parts store were pretty certain it is downstream driver's side, but I just want to make sure before I PB Blasted and removed it. 2008 F250 SD v10 ....
View 1 RepliesCamry :: 05 Solara Loses Power While Driving And Getting Codes P0172 And P2196
My Solara is running horribly. Its acting like the fuel pump or regulator is acting up as it loses power while driving and pumping the pedal usually does nothing. Its so bad that I cant drive it since top speed is about 10mph. If I just slightly touch the gas while driving I can get up to speed a little. It stalls when idling often too.
One thing I notice is if I stop driving for a while (with engine running) sometimes I can then drive away and the engine seems almost normal for 1-2 mins with lots of power. When the engine is cold it usually drives for 2 mins before these problems start.
This is a 2005 Solara. 4cyl 2AZFE gas engine - automatic - all stock - roughly 100,000 miles on the clock.
Its giving 2 codes: P0172 and P2196
I have looked up these codes and from reading I thought to try replacing the MAF sensor - no difference.
It feels like I'm driving a car with a bad carburetor again - really bogs out and laggy and sometimes even sounds like its backfiring slightly.
A bit of history:
- a few months ago I got the P0031 code so I replaced the upstream o2 sensor and all was good for a month or so.
- then about a month ago I got the P0136 code so I replaced the downstream o2 but it was starting to run badly before I could install and when I replaced it there was no change.
- last week I was surprised to see codes P0113, 172, 300, 301, 302, 303, and 136 but found that the battery terminal voltage was 10.5v so I replaced battery and those codes do not come back now.
- I'm thinking that due to the bad battery maybe the o2 sensors were not a problem? The upstream replacement made no difference (though it was running fine-just the CEL came on), and the downstream replacement made no difference (runs badly before and after).
My guess is fuel pressure, regulator, or injectors but its just getting too expensive to try.
Saturn - Sl :: 2002 - SES Light Has Been On Constantly - Codes P0172 / P0300 And P0507
Saturn 2002 SL1 5-speed. My SES light has been on constantly for about a year (was intermittent before that) with the codes P0172, P0300 and P0507. The car also idle high (2500+) occasionally at stops. My mechanic said it is likely an intake gasket but would need a full diagnostic to determine and that is not a safety hazard to drive but that I am getting less mph. I can't afford to fix it now but I have an emission test due. Is there a way to turn to light in the mean time?
View 1 RepliesFord F-150 (2004-2008) :: Start / Run Rough For A Second Then Die - Codes P0172 And P0175
First off its a 2006 F150 king ranch with the intercooled roush kit and roush tune. Last couple weeks its progressed from a slight stumble on start up, to now after its been off for a few hours it may start and run rough for a second, or, it may start then die, and then have to crank for at least 5 seconds before it starts. After it starts it seems to run fine. I've thrown the P0172 and P0175 code a few times. I downloaded the torque android app and did some data logging. Can you learn anything from the long term fuel trim?
View 9 RepliesFord F-150 (2004-2008) :: Gode Codes P0172 / P0300 And P0303?
My son just left. We scanned his truck and got these codes.
P0172 Bank 1 rich P0300 random misfires P0303 cylinder 3 misfires.
I used the Torque APP Pro to check these codes. I went to live readings in the Torque APP and saw some readings for Long term and Short term bank 1 Readings.
They are all "greek" to me, and I don't recall what they were, but could get those readings tomorrow.
When I have done searches combining these codes together, I see changing spark plugs. P0172 alone gets me a different train of thought. Mainly CAT issues.
Also, his cranking to start is quite long. (A lot longer than my 6.0L would ever think of cranking) At least nearly 30 seconds of cranking. We are leaning toward first just changing #3 plug.
Corolla / Matrix 2009-13 :: P0031 And P0172 Error Codes - Car Sputters And Hesitates
My girlfriend drives an 09 corolla (1.8L I believe). I have an OBDII bluetooth reader w/ Torque App so to identify the issue I can get some data:
Last week I was driving the corolla and I got P0031: HO2S Heater Control Circuit Low (Bank 1 Sensor 1). Car seemed to run fine without any issues. My girlfriend brought her car in to her "mechanic". "mechanic" who will replace have of your engine only to realize that your gas cap was cracked. He apparently replaced 02 Bank 1 Sensor 2 (I'm still trying to confirm this and to get the part # to make sure). He reset the ECU and she drove for about 30 miles after which these codes popped up:
P0172: System too Rich (Bank 1)
P0101: Mass or Volume Air Flow Circuit Range/Performance Problem
The car was idling rough. I reset the codes and the car was running fine until all monitor systems were ready. When Catalyst, 02 Heater & 02 Sensor are not ready everything is running fine and I don't see any error codes. I cleared ECU a few times. The last time I was able to drive for over 20 miles without any issues. Currently the only sensor not ready is 02 and car is running fine but I have a feeling once its ready the car will start having issues again:
Summary (if you don't want to read everything)
*P0031: H02S Heater Control Circuit Low (Bank 1 Sensor 1) - Car runs fine
*Mechanic replaces 02 Bank 1 Sensor 2 (Trying to find part # and double check sensor name)
*ECU reset and car runs fine for 30 miles
*P0172: System too Rich (Bank 1) and P0101: Mass or Volume Air Flow Circuit Range/Performance Problem
*ECU reset - car sputters and hesitates
*When all monitors are ready same codes (P0172 & P0101)
Ford F-150 (2004-2008) :: CEL On - P0172 / P01275 / P2106 Codes But Running Fine?
so i had a litle fun in the clay today ..and now my trucks check engine lights on ..i have a code reader im running a P0172 P01275 P2106 Ive cleaned the MAF and changed my air filter...still running the three codes afterwords no trouble with turning over starts right up and drives with a normal amount of power....its a 2004 5.4L V8 ...
View 12 RepliesFord F-150 - 1997-2003 :: Shaking And Idle Bounces Between 500 And 750 - Codes P0172 And P0174
2003 f150 5.4, 4x4 ... Truck is shaking pretty bad, idle bounces between 500 and 750, and its throwing p0172 (rich on bank 1), P0174 (lean on bank 2), and it looks like a misfire on cylinder 8 judging by that power graphy thingy. I'm going to check for a vacuum leak tomorrow on the PCV.
View 2 Replies