Ford F-150 - 1997-2003 :: Engine Running Rough During Idle And Driving
I am having a problem with my 1997 f150 4.2 v6. The engine is running rough at idle and while driving. It's running so rough that it vibrates the entire cab of the truck. I found water in the oil when I was trying to fix the problem. I have since had the heads redone and replaced all of the gaskets thinking this was the reason for the rough idling and rough driving. It wasn't; doing this fixed the water in the oil but still I have the rough running engine at idle and driving.
I have replaced the EGR valve, plugs and wires, pcv valve, replaced the coil pack, fuel filter and air filter (everything has been replaced with ford recommended parts because I have read that the engine I have doesn't like after market parts). While driving the engine vibrates and sound as if it's going in a cycle in a rhythmic sort of way (like a washing machine goes in a cycle), best way I can explain it. I have come to the end of what I think it is?
Ford F-150 - 1997-2003 :: 1998 - Rough Running Truck When Accelerating
I have a 1998 F150 4.6 2wd regular cab with 255,000 miles on it. Lately it has had some problems. The first is that it will run really rough when under a load, meaning when I step on the gas. It runs smooth at idle and at cruise but when I step on the accelerator it bogs way down and almost shuts off. I have changed the spark plugs, spark plug wires, coil packs and fuel filter. Now I'm thinking maybe fuel pump?
The other issue is that when the truck is having to work a little harder (i.e. pulling a trailer or running in the summer with the AC on) it will start to run hot. I have changed the thermostat, flushed the coolant, cleaned out the radiator, etc. and it still does it. Could both of my issues be related to a fuel problem??
Ford F-150 - 1997-2003 :: 1999 5.4L - Idle / Running Rough Occasionally
I purchased a 1999 F-150 Lariat 4x4 automatic transmission about a year ago. When I did, the previous owner told me about an idle issue that he has occasionally. He said that the issue was with the IAC. He claimed that he had replaced it several times but "it was hard to get a good aftermarket IAC that actually works". He said he tried several, but it never fixed the issue. That sounds like he wasn't replacing the defective part to me, but I don't know. This is my first truck to ever purchase.
Fast forward a bit (about a year), and I have had intermittent issues with idle and running rough since I bought the truck. I don't drive the truck that often, but they are becoming more common, so I want to get things fixed now.
Issues:
1. When running at idle, especially in park, the idle seems to fluctuate and never stay consistent. The idle drops as soon as I put it into drive, and the truck jerks a bit when going into drive because the idle was too high in park. It has never died while at idle, however.
2. When driving, especially up a slight or moderate hill, the power seems low and the truck starts to ping and jerk. The only way I can avoid the jerking is to stomp on the accelerator and go into a lower gear. And even when doing that, I still can notice an ever so slight jerk.
3. This past week, it was rough for an entire 40 mile journey on the interstate. Slight ping the entire ride home. When I pulled into the driveway, it was jerking until I turned it off. I haven't tried to drive it sense.
Potential issues:
1. IAC - maybe the previous owner was right. Maybe I should replace it again, or clean it with some carb cleaner.
2. Cam Phasers - I saw some posts about this on the forum.
3. EGR valve - Also saw some posts about this.
4. Maybe even the transmission? It doesn't seem to have an issue going into or out of gear, though.
Ford F-150 - 1997-2003 :: 2002 V8 Running Rough - Codes PO353 And PO171
2002 F150 5.4 v8,,, I had troubles just over a month ago with a po305 code. i got the truck fixed with 2 new coils n some gaskets. I am having these po353 & po171 codes pop up now. The truck is running rough and I am curious to if its just another coil problem or if their is something I am overlooking or just don't know about?
View 1 RepliesFord F-150 - 1997-2003 :: 2002 - Running Rough - PO316 And PO306 Codes
These are the code that keep spitting out. I have a 2002 f150 5.4L supercrewand it is running rough. I had this problem about 3 months back but i didnot get any codes from the computer i washed my truck a 1/2 day earlier, 2days later it went away. this time it has spit out 4 codes a po306/po307/po300/po316. the po307 and the po300 are gone, but the other two remain and it is still running rough 2days later. i had just washed my truck 30min. before, it started happening, is there water somewhere? My dad (long time mechanic) says use wire dry on the cops and it will go away. I have read other post on misfiring and I am still not sure what to do?
View 10 RepliesFord F-150 - 1997-2003 :: 2002 - Running Rough And Check Engine Light On
My girlfriend has a 2002 F-150 with the 4.6 V8 and I was going to change the spark plugs for her. She said it started running rough and it threw a code and check engine light. She took it for a scan and they told her the number 5 plug was mis-firing. I'm fairly handy and bought a set of the recommended Motorcraft plugs from Rock Auto, AGSF32PM. It also matched the number in the owners manual so I thought I was pretty safe.
Funny thing, when I took the old ones out, they were AGSF22WM's instead. My thinking is they are a colder plug than the supposedly original equipment, but I don't think they've been changed before. They looked well used but the color was good. The truck has about 135K on it.
Long story short, and to get to the question(s), Would there be any reason the factory would have put a different plug in the engine than what is listed? Am I asking for trouble going with a hotter plug than what's been in there (pinging or timing retardation/loss of power)? Am I just overthinking the whole thing and need to put it back together and drive it?
Ford F-150 - 1997-2003 :: Truck Suddenly Started Running Rough / Too Many DTCs All At Once
I have a 2001 F150 4.6L auto. This truck suddenly started running rough. Cleared all codes and re-scanned after starting truck. The codes are as follows; P0135, P0155, P0443, P0740, P0743, P0758, P1451, P1460, P1747, and P1760.
My question is; is it normal to have this many DTCs come up at once? Could my PCM be faulty causing this problem? Can you swap a pcm from the same year truck with the same options without reprogramming?
Ford F-150 - 1997-2003 :: Running Rough - Surging In Park / Drive And Reverse
I have a 1997 ford f150 5.4 litre truck and the truck runs real rough kinda surging in park and in drive and reverse i have a couple oxygen sensor codes P 0171, P0174, P0136, P1131, P1151 and an idle air control valve code P1506...
View 5 RepliesFord F-150 - 1997-2003 :: Truck Running Rough And Hesitating - Codes PO141 And PO171
2001 F150 4.6. Just replaced all 4 oxygen sensors and spark plugs. Replaced rubber grommet on brake booster as it was leaking vacuum.
Truck is still running rough hesitating.
Pulled codes came up as PO141 oxygen sensor heater circuit. PO171 passenger side cylinders running lean. Fuel trim outside limits.
Ford F-150 - 1997-2003 :: Check Engine Light Started Flashing / Running Rough Then Went Off
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 RepliesFord F-150 - 1997-2003 :: Running Rough Under Light Acceleration / Codes P0300 And P0301
Just got a 98 f150 w/ 5.4 4x4 excab. It idles fine but under light accleration. It starts bucking and missing bad, if I step on it, it down shifts and accelerates fine. If I try to maintain one speed it misses bad. It is not throwing any codes right now. The check engine light did come on for like a minute but went back off before I could have it read. I hooked up a scanner just to see if any codes were stored and got p0300 and p0301. I am going to clean the MAF and check for vacuum leaks. I hear the rear plug and coils can get water in them causing similar problems.
View 8 RepliesFord F-150 - 1997-2003 :: 2000 - Idling And Running Rough On Acceleration - P0171 Code?
My daughter returned from college with her 2000 f150 4.2 idling and running rough on acceleration. It is throwing a P0171 code only. I replaced the isolator bolts/plenum gaskets four years ago because of a P0171 & P0174 codes.
So far I have replaced the MAF, new PCV valve and elbow, checked all obvious lines for vacuum leaks (though I suspect a leak somewhere still). Also, a quick check of the plugs show some lean color/deposits on the drivers side only. Any thoughts or troubleshooting I should try next?
Ford F-150 - 1997-2003 :: Truck Running Rough / Intake Manifold Gasket Blown
I have been having some issues with my 97 ford f150 4.6 liter, started out running rough, then hydrolocked with no serious damage, blown intake manifold gasket, fixed that, alternator over charging do to bad voltage regulator, fixed that. and airbag code 52, still working on that, as well as failure to connect when trying to do diagnostic scan. now I am wondering if the engine diagnostic is still even working. still running good just a very slight vibration when warms up. I am not getting any code. or my check engine light is not showing any codes. What I want to do is force a code. What would be the safest way to force a code or force engine light to give a code?
View 6 RepliesFord F-150 - 1997-2003 :: 1999 - Misfire / Running Rough - Code P0305 And P0174
Here is my situation : I have a F150 1999 4x4 ext cab with 326 000 km. A little while ago I got a P0401 code so I decide to clean the TB first and at the same time change plugs and wires since they were overdue. The same code came back and a misfire. Ordered EGR valve, DPFE sensor and selenoid. Realize that I had ordered crappy plugs by mistake. I change all plugs. Had to wait for the EGR valve and others to arrive. I drove the truck for a while since I did not have the time to change the valve and others, during that time the misfire did not come back. Yesterday I change the EGR and others. Today I get a truck that runs really rough and got new codes , P0305 and P0174. I'm really confused now on what should be my next step, should I change the coils, can a P0305 cause a P0174. Should I change vacuum hose going to the EGR , selenoid and DPFE.
View 12 RepliesFord F-150 - 1997-2003 :: 4.2L V6 Hard To Start / Occasionally Running Rough And Losing Power
I recently bought a 4.2L V6 2003 F150 with only 20,350 original miles. This car belonged to an older gent who barely used it, then passed on about 3 years ago, and truck sat around barely used by anyone. When I picked it up I ran some Seafoam through the first two gas tanks as it was occasionally running rough and losing power. Since then truck has been running incredibly smooth, but in the last few days it is getting harder to start. If I pumped it two or three times it would start OK, but today I have had to pump it while cranking it to get it to start. ( the pumping may have nothing to do with it starting)
I am replacing the fuel filter in the next couple of days, as any accumulated junk that was in the tank or lines is now probably in the filter, but it seems that a badly clogged filter would also give me some problems running, and it runs really smooth once it starts. I get a pressure gauge, (I understand the rails have a pressure test port) what pressures should I expect at what moments?
Turn key on :
Crank engine :
I am brand new to the F150 and trucks in general.
Ford F-150 - 1997-2003 :: 2000 - Bogs Down / Running Rough And Shutters A Lot - Code P0171
I've got a 2000 f150 with a 5.4 and 135,000 miles. The other day it was driving fine then i stopped and got gas and after that it was boggy and running rough so i thought bad gas but i ran through that gas and got more at a different store. The cel came on i got it checked it was misfire cylinder 1 so i put new cop, spark plug, and injector. Unhooked the battery and then the light came back on so i ran the code and now im getting a p0171. I checked the pcv and sprayed around the intake and vacuum lines. I also checked the pcv hose and elbow in the back and i found nothing its a fairly new hose. So, it does run rough it shutters a lot.
View 2 RepliesFord F-150 - 1997-2003 :: 2000 V8 Running Rough At Idle And Check Engine Light On
I started out with my 2000 F150 with a 5.4 V8 running rough at idle. It would idle way down slow and then rev up a little over and over. On a couple of occasions it would even die when in drive or reverse. I did finally get a Check Engine light so i put it on my diagnostic program to see what was up. Here is what I got:
P1151 Lack of HO2S21 Indicates Lean
P0171 System Too Lean Bank 1
p0174 System Too Lean Bank 2
After doing some reading up I checked all my vacuum hoses and cleaned my mass air flow sensor. I then got the same codes again after a few minutes of running. So I went to the next thing that was recommended, the upstream bank 2 O2 sensor. After changing it the truck ran fine for a couple of days, no issues. Then all of the sudden it idled a little funny again and I got a Check Engine Light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0300 Random/Multiple Misfire
I reset the light to see if I would get the same again later. Before the light came on again I filled my truck up with gas and it seemed to be running pretty good again. Then a day or so later it set the light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0136 O2 Circuit Malfunction Bank 1 Sensor 2
P0156 O2 Circuit Malfunction Bank 2 Sensor 2
P1131 Lack of Switches HO2S11 Lean
P1151 Lack of Switches HO2S21 Lean
I went ahead and drove for a few days as it had gotten really cold here and I didn't feel like messing around in my shop since it isn't heated. A couple days ago I needed gas so i filled up again. Suddenly the problem was gone again. Truck ran fine idled fine no missing or odd idling at all. That lasted a day or two before it started acting a little weird again. At that point i was down about 1/8 of a tank from full. I have read that there can be issues with the fuel pump.. I am kind of wondering if that may be it now. But I haven't had to deal with this sort of issue before so I am unsure what to check next. The truck always runs fine off idle, it only seems to have the issue when it is idling. I had reset the codes the last time and i have the light on again now. I haven't checked it yet but I am sure it is going be some combination of what i have had in the past.
I have read that the IAC valve can be an issue as well. I had a problem with mine sticking a couple years ago and when it would do it you could just tap it with a wrench and it would idle up. But it never died like it does now and it would also idle a lot slower than it does. Back then I cleaned the valve and had no more issues with it. The truck has always had times when it would act weird at idle usually after slowing down after being at highway speed. The current issue happens at all temps cold or hot.
Ford F-150 - 1997-2003 :: Idling Rough And Check Engine Light Came On After Running For About 20 Minutes
I replaced the heater core in my truck this weekend. The only thing I was worried about was pulling the dash. The truck is a 1998 f150 with the 5.4.. Everything went fairy well and decided to replace the AT Shift cable as well. Got everything put back. Truck runs, no leaks, no antifreeze smell. After running about 20 minutes, it started idling a little rough and my check engine light came on.
The codes are p0136, p0156, p1131, and p1151. I know these are related to the OS sensors. My question is could it be as simple as I miss an electrical connection when putting the dash back in? Was thinking possibly somewhere on the passenger side under the kick plate or possibly something while hooking up the heater hoses? Maybe even a ground that didn't get connected back when putting the das back in?
Ford F-150 - 1997-2003 :: 2001 - Running Rough When Cold / Stalling Out When Coming To A Stop Light
2 questions regarding our 2001 F150 Supercrew. My 2 questions are:
My 2001 Ford F150 Supercrew (5.4L, 230,000 miles)has the check engine light on with the code reader telling me that it is the P0174. The truck would run rough when cold (usually in the mornings) and sometimes it would get close to stalling out when coming to a stop light. So we would quickly put it in park and give it some gas to rev it up a bit. After the truck gets warmed up, it runs great with no hint of the rough idle. Since this all started I have changed out the PCV valve and replaced the PCV hose (including the elbow). I have also replaced the Idle Air Control unit but that didn't really make a difference.
We then experienced a cylinder #4 misfire which we resolved by changing out the cop with a new Motorcraft unit. The misfire went away but we still had the problem of running rough at idle to the point of stalling out at stops when the engine is cold. A few weeks ago we cleaned the MAF sensor and that seemed to work. The truck doesn't run as rough now (when cold) at stop-lights, but occasionally it will still have the loping idle. We cleared the check engine code and it stayed off for about a week before returning.
I don't know what else to check other than trying to see if there is some type of vacuum leak, but I don't have access to a smoke machine nor would I know how or where to hook one up. Removing and cleaning the throttle body would work? What could be causing the trouble, or what I should do to further isolate or troubleshoot the problem? I saw a you-tube video on the F150 intake manifold gasket possibly being the problem and although I hope that isn't the trouble with my truck, if it is then I will have to deal with it. We need the truck to get to work and the car is now due for a registration renewal, but we can't get a California smog certificate with the check engine light on.