Ford F-150 - 1997-2003 :: 2002 - Running Rough And Check Engine Light On
My girlfriend has a 2002 F-150 with the 4.6 V8 and I was going to change the spark plugs for her. She said it started running rough and it threw a code and check engine light. She took it for a scan and they told her the number 5 plug was mis-firing. I'm fairly handy and bought a set of the recommended Motorcraft plugs from Rock Auto, AGSF32PM. It also matched the number in the owners manual so I thought I was pretty safe.
Funny thing, when I took the old ones out, they were AGSF22WM's instead. My thinking is they are a colder plug than the supposedly original equipment, but I don't think they've been changed before. They looked well used but the color was good. The truck has about 135K on it.
Long story short, and to get to the question(s), Would there be any reason the factory would have put a different plug in the engine than what is listed? Am I asking for trouble going with a hotter plug than what's been in there (pinging or timing retardation/loss of power)? Am I just overthinking the whole thing and need to put it back together and drive it?
Ford F-150 - 1997-2003 :: Check Engine Light Started Flashing / Running Rough Then Went Off
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 RepliesFord F-150 - 1997-2003 :: Idling Rough And Check Engine Light Came On After Running For About 20 Minutes
I replaced the heater core in my truck this weekend. The only thing I was worried about was pulling the dash. The truck is a 1998 f150 with the 5.4.. Everything went fairy well and decided to replace the AT Shift cable as well. Got everything put back. Truck runs, no leaks, no antifreeze smell. After running about 20 minutes, it started idling a little rough and my check engine light came on.
The codes are p0136, p0156, p1131, and p1151. I know these are related to the OS sensors. My question is could it be as simple as I miss an electrical connection when putting the dash back in? Was thinking possibly somewhere on the passenger side under the kick plate or possibly something while hooking up the heater hoses? Maybe even a ground that didn't get connected back when putting the das back in?
Ford F-150 - 1997-2003 :: Engine Running Rough During Idle And Driving
I am having a problem with my 1997 f150 4.2 v6. The engine is running rough at idle and while driving. It's running so rough that it vibrates the entire cab of the truck. I found water in the oil when I was trying to fix the problem. I have since had the heads redone and replaced all of the gaskets thinking this was the reason for the rough idling and rough driving. It wasn't; doing this fixed the water in the oil but still I have the rough running engine at idle and driving.
I have replaced the EGR valve, plugs and wires, pcv valve, replaced the coil pack, fuel filter and air filter (everything has been replaced with ford recommended parts because I have read that the engine I have doesn't like after market parts). While driving the engine vibrates and sound as if it's going in a cycle in a rhythmic sort of way (like a washing machine goes in a cycle), best way I can explain it. I have come to the end of what I think it is?
Touareg :: Running Rough At Idle Then Check Engine Light Comes On
Filled tank with 8 gallons of 91 octane to top off. One hour later noticed car running rough at idle then check engine light comes on. Could it be the coil pack? Car has been running very well until now, and this Gremlin appears. I don't think it's the gas.
2004 -V8 Treg
52,000 on the odometer
Ford Ranger / B-Series :: 2003 3.0 - Misfire On Cylinder Six / Running Rough And Check Engine Light On
I have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 RepliesPassat (B5) :: 2003 - Check Engine Light Came On And Car Is Running Really Rough At Stops
I have an 03 Passat with about 70K miles on it. My daughter put rug in it this morning (about 7 gallons) and since then the check engine light came on and the car is running really rough at stops. While accelerating, it seems to be fine. It is also getting about 10 mpg less than normal. MIL codes: P0300, P0301, P0302, P0303, P0304, and P0171. He said the P03xx codes were related to misfirings on each cylinder. The P0171 is a bank 1 failure (?). What do those codes really mean and could they be related to bad gas? Sent her off in my TDI JSW so she's not out on the highway if the Passat decides it doesn't want to go anymore.
View 6 RepliesFord F-150 - 1997-2003 :: 1999 - Service Engine Soon Light On Sometimes At High Rpm Or Rough Erratic Idle
My trucks symptoms include a illuminated service engine soon light, sometimes a high rpm idle, and sometimes a rough erratic idle. When a scan was done it indicated the oxygen sensor was defective. The issue is: which specific one (there are multiple oxygen sensors) or how could I check or determine the faulty one for sure. I am trying to economize and replace only the bad one myself if possible. I own a good multimeter, can it determine the bad one? 1999 F-150 4.2 Litre V6 oxygen sensor dillemna....
View 7 RepliesFord F-150 - 1997-2003 :: 2000 - Check Engine Light Came On / Truck Started Shaking
I have a 2000 f150 4x2 5.4 168k... Check engine came on,started shaking, weather was really cold. RPM would be a little high then low then back up. Especially when I turned on heater. Felt like truck would die but never does nor does it have issue starting.
So far, I have replaced two oxygen sensors inside engine,all coils, spark plugs, fuel filter, had injectors cleaned, intake cleaned. Truck runs better but, light came on a day later again. I can feel the tiniest of shaking going on and, cold mornings still make RPMS a little unstable. I was driving truck on highway at about 60 mph when a slight tug was felt and Truck check engine came on. I feel truck heavy, once it warms up completely, a little lighter.
Codes came up at auto zone as P1151
But I'm running out of options and frankly, money to fix this truck.
Checked the MAF and looked okay.
I'm with minimal skills.
Ford F-150 - 1997-2003 :: 1999 5.4L - Idle / Running Rough Occasionally
I purchased a 1999 F-150 Lariat 4x4 automatic transmission about a year ago. When I did, the previous owner told me about an idle issue that he has occasionally. He said that the issue was with the IAC. He claimed that he had replaced it several times but "it was hard to get a good aftermarket IAC that actually works". He said he tried several, but it never fixed the issue. That sounds like he wasn't replacing the defective part to me, but I don't know. This is my first truck to ever purchase.
Fast forward a bit (about a year), and I have had intermittent issues with idle and running rough since I bought the truck. I don't drive the truck that often, but they are becoming more common, so I want to get things fixed now.
Issues:
1. When running at idle, especially in park, the idle seems to fluctuate and never stay consistent. The idle drops as soon as I put it into drive, and the truck jerks a bit when going into drive because the idle was too high in park. It has never died while at idle, however.
2. When driving, especially up a slight or moderate hill, the power seems low and the truck starts to ping and jerk. The only way I can avoid the jerking is to stomp on the accelerator and go into a lower gear. And even when doing that, I still can notice an ever so slight jerk.
3. This past week, it was rough for an entire 40 mile journey on the interstate. Slight ping the entire ride home. When I pulled into the driveway, it was jerking until I turned it off. I haven't tried to drive it sense.
Potential issues:
1. IAC - maybe the previous owner was right. Maybe I should replace it again, or clean it with some carb cleaner.
2. Cam Phasers - I saw some posts about this on the forum.
3. EGR valve - Also saw some posts about this.
4. Maybe even the transmission? It doesn't seem to have an issue going into or out of gear, though.
Ford F-150 - 1997-2003 :: 2000 - Rough Idle When Outside Temp Below 50
2000 Ford F150 1/2 ton 2x 5.4L... Last year, I started having a problem where when the temp dropped below 50 degrees outside, my F150 would idle really rough and sometimes stall out. The CEL came on and reported some codes that I don't remember but pointed to bad air/fuel mix. I consulted a friend and he suggested changing out the IAC. I did that just towards the end of the cold weather spell we were having and the engine ran great so I assumed it was fixed.
Well, the temps have been below 50 for 8 days now and ever since the temps dropped the problem has come back. I took it to AutoZone to have the codes read and they gave me the following:
P1151 - Lack of O2 switches -bank 2 sensor 1 : ECM could not adjust fuel trim because of a lean or rich condition
AND
P0171 - Fuel trim bank one condition : The powertrain control module uses the oxygen sensor to calculate the Air/Fuel ratio of the engine. The computer recognized a rich or lean condition on one engine bank only.
Both printouts that they gave me mentioned the following:
Poor fuel pressure
Bad or Malfunctioning MAF sensor - Dirty/defective
Oxygen sensor defective
Fuel injector problem - Leaking or fuel pressure high/low
Vacuum leak on engine
I again called my mechanic friend and he suggested cleaning the MAF and if that didn't work replacing the MAF. I cleaned it and the problem was better but still not fixed.
Ford F-150 - 1997-2003 :: 2000 - Idling And Running Rough On Acceleration - P0171 Code?
My daughter returned from college with her 2000 f150 4.2 idling and running rough on acceleration. It is throwing a P0171 code only. I replaced the isolator bolts/plenum gaskets four years ago because of a P0171 & P0174 codes.
So far I have replaced the MAF, new PCV valve and elbow, checked all obvious lines for vacuum leaks (though I suspect a leak somewhere still). Also, a quick check of the plugs show some lean color/deposits on the drivers side only. Any thoughts or troubleshooting I should try next?
Ford F-150 - 1997-2003 :: 2000 - Bogs Down / Running Rough And Shutters A Lot - Code P0171
I've got a 2000 f150 with a 5.4 and 135,000 miles. The other day it was driving fine then i stopped and got gas and after that it was boggy and running rough so i thought bad gas but i ran through that gas and got more at a different store. The cel came on i got it checked it was misfire cylinder 1 so i put new cop, spark plug, and injector. Unhooked the battery and then the light came back on so i ran the code and now im getting a p0171. I checked the pcv and sprayed around the intake and vacuum lines. I also checked the pcv hose and elbow in the back and i found nothing its a fairly new hose. So, it does run rough it shutters a lot.
View 2 RepliesFord F-150 - 1997-2003 :: 2000 - Rough Idle / Codes PO304 And PO174
I have a 2000 F150 4.2L and I have 2 codes PO304 & PO174 so far I have changed my plugs & wires,fuel filter,mass air flow sensor, and coil pack...it is still running rough under a load and a little rough on idle..
View 9 RepliesFord Excursion :: Running Rough And Check Engine Light Came On - P0353 And P0358 Codes
The X has been running great, well good enough, lately with no issues. I left work the other morning, and apparently the X didn't want to wake up that early. As soon as I started it up, the check engine light came on and it was running like crap. Had a bad hesitation all the way home. It feels like it is misfiring, but only under load. It doesn't do it if I brake torque it or Rev it up. Only while driving.
The codes I am getting are in the P035x family (typed that way for future searches). P0353 and P0358 are the codes I am getting (along with 4x4 codes for the vacuum solenoid...but that's the solution to other problems not relevant to this!). Being codes for the primary circuit, I popped the hood and checked out the connectors. Both connectors are fine, and tightly connected. I did notice however that cylinders 3 and 8 have other than OEM coil packs on them. These are the only 2 cylinders with those coil packs (they are white and the other 8 cylinders have black coils).
I don't want to just throw parts at it, and I'm not getting a hard miss fire code, just the 2 above. I might try to swap the coils with other cylinders tonight and see if the codes move to those cylinders. It has run like this a few times, but never set a code, and turning it off and back on has "fixed"this in the past.
And just for complete disclosure, while looking for where I saved a password, I found notes from August last year where I pulled codes, and these two codes were present then, with a cylinder 7 hard miss fire code. I replaced the c7 coil with motorcraft cleared the codes, and P0353 and P0358 went away and I haven't seen them since. The plugs are brand new and only have about 1000 miles on them (changed them in September when repairing the misfire and I don't drive it much).
Ford F-150 (2004-2008) :: Stumbling / Running Rough - Check Engine Light Is Either On Steady Or Flashing
Got an 07 Screw with only 50,000 miles. Yesterday, wife drove it home from work and said it would only do 45mph and didn't sound good. No warning lights were on, she said. I test drove it in the evening and it ran totally fine. Today, she drives it to work and said it ran real rough and "Check Engine" light was on. I picked it up from her work and it idles very rough and slow, and once you hit about 2000 rpm, it runs decent, maybe even normal. Below that, it stumbles and engine doesn't sound right. "Check Engine" light is either ON steady, or flashing. I don't have a code reader, so its likely going to the Ford Dealer Monday. Is there any way to read the code without a reader?
View 11 RepliesFord F-150 (2004-2008) :: Check Engine Light Flashing - Running Rough With Tapping Noise
2005 F-150 4.6L 2WD, 268,000 miles....
Recently I got a flashing 'Check Engine' light and a rough running engine (along with a tapping noise) when I was passing someone (and pulling a trailer). I retrieved codes 300, 304, & 305. I can't swear to it, but I think the tapping noise started at the same time as the coil problem.
I replaced coils #4 & #5 (later that same day) and the engine smoothed back out but the tapping noise is still hanging around. The noise speeds up at higher RPM's and doesn't go away if I shift into neutral. Oil level and pressure are fine and I only use Motorcraft 5W-20 and Motorcraft filters (and change the oil every 5K miles).
Not sure if this is relevant: I think I have bad valve guide seals (blue smoke after long idles) but no other problems that I am aware of. It sort of sounds like a lifter, but is there a good way to pin it down? Is it possible that this tapping is related to the bad coils?
Golf IV / Jetta IV :: 2000 - Rough Idle - Flashing Check Engine?
The check engine light came on in my 2000 Jetta and the engine power suddenly decreased noticeably. Got worse quickly and was idling rough, like it was about to stall out (but didn't). Took it to dealership, they said spark plugs were the problem and replaced. All seemed normal driving home, but after 10 minutes, same problem: check engine flashing, weak engine (trouble on hills), and a rough idle.
Two questions: what could it be?
and is it safe to drive back to dealership (~10 miles) or might that cause further damage?
Ford 6.7L Power Stroke Diesel :: 2011 - Check Engine Light Came On And Truck Started Running Rough
Well it finally happened, a couple of weeks ago I was headed to an MX race and my check engine light came on and it started running rough. Long story short a piece of an exhaust valve broke off and went out through the head. Dealer has been great even though I was 300 miles from home and they did get me a rental(small POS SUV). Truck was supposed to be finished this week, but now they are saying the head gasket is on back order and they probably won't have one until the middle of April......... I can't be without my truck that long, but not much I can do. By the way truck is completely stock with just under 20K on it, and I have never had any issues with any of my Ford trucks or Ford diesels, even my old 6.0.
View 7 Replies