Ford F-150 - 1997-2003 :: 2002 F150 5.4 - CEL Came On For Code P0174 - Misfire On 7 Of 8 Cylinders
So the past few weeks my truck has been sputtering a lot. It seems to do it more so in low RPMS but when I lay on the throttle I didn't really notice it. I haven't had time to look into the issue but yesterday the issue got drastically worse and the CEL finally came on. Registered P0174 as well as a number of other codes including misfires on 7 of the 8 cylinders.
So far I have replaced the fuel filter. Spark plugs are only a few months old. I didnt think it would make sense for all of the coil packs to go out at once so I was thinking either a fuel issue or vacuum leak. Why would it only spit out P0174 (Banks 2) and not show P0171 (Banks 1) along with it? Fuel pump? Vacuum leak? Where should I start? 2002 F150 5.4L...
Ford F-150 - 1997-2003 :: 1998 4.6L - Misfire On Cylinder 6 / Code P0171 And P0174
P0306 (ok #6 missfire) with P0171 & P0174 --- Do I chase electrical or fuel or both. Afraid to assume anything but probably would normally address the misfire electrical first.... Don't want to go down that 'primrose path' if others have been there first!
View 4 RepliesFord Super Duty (1999-2016) :: 2001 - Running Rough - Code P0174?
2001 V10- F250.. Runs rough- had the computer put on it and was coming up with P0174 codes (I think that is right)- In any case I replaced the Mass air flow sensor- checked for any vacuum leaks visually- I did not see anything obvious.... still runs like crap.... smells like gas when idling.... anything else I can check??? The check engine light went off finally (probably due to the MAF)- but it's driving me nuts- Any hoses I have not located I need to check?
View 10 RepliesFord Ranger / B-Series :: 1999 - Code P0305 Cylinder 5 Misfire
I have a 1999 ford ranger 3.0 6 cyl with 211,110 miles It started running rough without any previous warning signs. In idle its barely noticeable, once i put it in gear it gets rougher and when driving around 40 to 45 mph it roughly shakes and shimmies. Once I get past the 40 to 45 mph range it settles back down. Is there a specific issue that would cause that at that speed. When going up over a bridge the check engine light blinks.
I changed the spark plugs and new wires and it offered no success even though one of the plugs were black (to much gas). I have borrowed a diagnostic tool and got P0305 cylinder 5 misfire, I am thinking fuel injector to replace, what else should I be looking at?
Ford F-150 - 1997-2003 :: 1999 - Truck Throwing P0174 Code Intermittently?
I have a 1999 F-150 with the 4.2L engine. I recently did a motor swap as the original motor was bad. I bought this truck as a project truck and have enjoyed working on it.
When I did the engine swap back in May of this year, it took a while to work out all the little bugs and quirps. However, after a while of running the truck it threw a few codes. I replaced a lot of the emission components and no more codes for several months until last month the truck started throwing the infamous P0174 "too lean bank two"... I have replaced the pcv valve and all the hoses to include the little rubber boot under the front of the intake, all 4 O2 sensors, MAF sensor, EGR, DPFE, IAC valve, new wires and plugs to include coil pack, fuel pressure regulator, and all the vacuum lines that are under the hood.
The truck runs fine, has power, but about every couple weeks or so it throws this P0174 code. I know there are alot of threads on here about this problem and I have read many of them. It only throws the P0174 and not the P0171. I am wondering if there could be a problem specific to "bank 2" that I am over looking.
Dodge - Durango :: 2003 - Code P0300 Random Misfire / Engine Running Rough
Just started getting a p0300 random misfire code on the durango a couple days ago. pretty sure it isn't moisture related since it started on a nice sunny day. it was running pretty rough so it was obvious that it was misfiring. I changed the plugs since it was about time anyway, and they needed it and I cleared the codes. new plugs (put in the oem champion copper plugs) didn't make the problem go away. The engine still ran rough and the code came back. 2 of the plugs looked like they may have been fouling a little bit. they were a fair bit blacker than the rest of the plugs. I went ahead and changed the coils on those two cylinders and reset the codes again. Still runs rough and the p0300 came back. where do I go from here? I am not getting any specific cylinder codes so it makes sense to me that it isn't one or two cylinders not getting spark. 2003 durango 4.7 ....
View 6 RepliesFord F-150 - 1997-2003 :: Throwing Code P0171 And P0174?
97 F150 4.6 200xxx on recent rebuild. My truck is throwing P0171 & P0174.
I think I tracked it down to leaky IAC and EGR gasket. I sprayed both with carb cleaner and the RPM's dropped.
My question is, wouldn't the RPM's rise instead of drop? I was under the impression that they would go up if the gaskets were leaking. Or did I use the wrong spray?
Ford Escape / Hybrid :: 2002 - Misfire - Getting Code P0305 And P0306?
I have a very Big problem with my Ford Escape 2002 I have this problems code: P0305 accuses Cylinder #5 P0306 accuses Cylinder #6.
I already change the gasket i buy the felpro Kit, and i Also replace all the sparks and spark plug boots, I clean the air sensors and i also replace the EGR, i try to switch cables, and all is the same the car start buy when i accelerate it just go off, i don't know what can i do next, somebody told me to change the fuel injector, i take the pressure in both spark holes the number 4 was 150 and the 5 and 6 was 120, No leaks oil. My car is a Ford Escape 2002, XLT 3.0 4x4
Ford F-150 - 1997-2003 :: 2000 - Idling And Running Rough On Acceleration - P0171 Code?
My daughter returned from college with her 2000 f150 4.2 idling and running rough on acceleration. It is throwing a P0171 code only. I replaced the isolator bolts/plenum gaskets four years ago because of a P0171 & P0174 codes.
So far I have replaced the MAF, new PCV valve and elbow, checked all obvious lines for vacuum leaks (though I suspect a leak somewhere still). Also, a quick check of the plugs show some lean color/deposits on the drivers side only. Any thoughts or troubleshooting I should try next?
Ford F-150 - 1997-2003 :: 2000 - Bogs Down / Running Rough And Shutters A Lot - Code P0171
I've got a 2000 f150 with a 5.4 and 135,000 miles. The other day it was driving fine then i stopped and got gas and after that it was boggy and running rough so i thought bad gas but i ran through that gas and got more at a different store. The cel came on i got it checked it was misfire cylinder 1 so i put new cop, spark plug, and injector. Unhooked the battery and then the light came back on so i ran the code and now im getting a p0171. I checked the pcv and sprayed around the intake and vacuum lines. I also checked the pcv hose and elbow in the back and i found nothing its a fairly new hose. So, it does run rough it shutters a lot.
View 2 RepliesFord F-150 - 1997-2003 :: CEL Came On When Coasting Down A Steep Hill - Code P0174
I was coasting down a steep hill yesterday when the CEL came on. I pulled the code this morning and got code P0174, system too lean bank 2.
I cleared the code. Should I just wait to see if it happens again? The truck is running great. There is no sign of a problem. BTW, it's 99 F150 5.4.
Ford F-150 - 1997-2003 :: Code P0171 And P0174 - Vacuum Leak
I had my fuel system cleaned by the dealership last weekend and I feel like I gained 50hp+ ... Now its throwing a P0171 about a week and a half later. My computer also listed P0174 under the pending codes or whatever the section was.
2003 F150 5.4L ... I cleaned the MAF sensor a couple weeks back which stopped a rough idle and I have put some 300+ miles on it since. about 200 miles since the fuel system cleaning.
I got home and popped the hood and it sounded like a vacuum cleaner. Guess it is a vacuum leak. I might need to stop using this ford house. I swear this is the second time there was a vacuum leak(I think, first time they said it was spark gap issue). I'll be heading back in the morning now.
Ford Super Duty (1999-2016) :: Running Rough - Check Engine Light Came On And Got Codes P0171 And P0174
My 1999 F350 SD V10 that would crank but not start. I ended up checking numerous things because before it decided to truly stop running, it would run rough for a time and then be fine. The check Engine Light came on and I got the codes P0171 & P0174. Well, I bought MAF Cleaner and took the air cleaner housing off, disassembled it and thoroughly cleaned the sensor and replaced the air cleaner. I continued to get those same error codes, but before I could go any further, the truck totally died. It sat for nearly 2 months with the bed in the air as I had decided to lift the bed to check the fuel pump vs. drop the tank.
Fast forward a bit and I have since replaced the fuel pump and put $40 of Premium Gas along with Royal Purple Fuel Treatment in the tank because I figured things got stirred up and could use a bit of cleaning. I do not drive much, and during the first few trips, it ran perfectly. Then today, it started again with the rough running and trying to die if I let it idle. If I pushed on the gas, it would completely smooth out. If this were a carbureted engine, I would think the low idle was set too low, but since it is not, I am guessing it is one or more of the sensor/s that is/are causing the issue.
I am disabled and can’t play parts swap until I hit on the right part, so I was hoping that I might get some guidance here to narrow things down to the most probably causes so that I won’t go broke changing things until I hit the “right one”. The truck has 153,000 miles on it and I had bought it from a retired couple who used it to pull their 5th wheel travel trailer, so it had mostly highway miles on it. It was immaculate when I bought it and ran perfectly, needing only normal maintenance (oil changes, etc.) over the past 12 years that I have owned it. In those 12 years, I have put about 60,000 miles on it.
Ford F-150 - 1997-2003 :: Truck Won't Start / Code P0174 Keeps Coming Back
I have a 2001 F150 XLT Supercab,4.2lt, automatic, 2WD.
I was able to start it about a month or so ago but it was really hard to start. I had to use starting fluid to get it started, and it was still tough to get it to start, but once started and warmed up it ran fine.
Now I tried to start it again and it kicks over and wont start. I tried the same with the starting fluid and it almost starts and dies. I think I used a little too much starting fluid because after a while of trying and spraying starting fluid, I got a hard backfire that sounded like a shotgun that was strong enough to pop off the MAF Sensor and throw it about 10 feet. I nearly crapped my pants! It looks clean and undamaged but I hope I didn't damage the MAF Sensor when if hit the ground.
The truck sounds like its starving for fuel, so I'm not sure if the fuel pump relay is going or has gone bad, or if its the fuel pump. How to check these items without making it a huge project to diagnose?
Once I can get it to start easily, I have a couple of questions about the trouble code that keeps coming back P0174. That was the original problem with it before the starting problem.The diagnostic says that it is lean in bank 2 but a mechanic friend of mine said something about a vacuum leak.
Ford F-150 - 1997-2003 :: 1999 - Ride Rough - Misfire On Cylinder 3?
I'm working on my 99 f-150. I replaced all my spark plugs and coils after I got a misfire on cylinder 3 reading on the scanner. The truck was running ok but two weeks later it started to ride rough again I checked the scanner and got the same reading for a misfire on cylinder 3. Why its giving me the same misfire again? Could my injector cause that misfire? What about the egr valve?
View 8 RepliesFord F-150 - 1997-2003 :: 1999 4X4 - Intermittent Misfire / Runs Rough For About A Minute
I have a 99 F150 Lariat 4x4 with a 5.4, 150,000 mile on it. About 2 weeks ago I blew spark plug out on #2, and a friend who said he has heli-coiled a bunch of these tried to do mine and ruined the head. Anyway, I called a local engine shop and got another PI head, only I used my cam in it. Torqued it as per the book, etc... Mind you that the engine ran perfect before all this.
Got it back together with all new plugs, new exhaust manifold, and 2 new COP's. When I start it-it runs rough for about a min, then straightens back out to run perfect again, and after a few seconds you can hear a solenoid click, then it goes back to missing again. This goes on and on... I went through all the vacuum lines and checked them, checked the egr valve, put on a new IAC, new PVC, cleaned the MAF, and checked everything else with a DVM.
I took it out and drove it.... Runs good for a minute, then it goes back to missing, then back to smooth again. This just keeps going on and on. I noticed when I hear that click, it sounds like a mad rush of air being sucked in, but I cannot locate it. I ordered a new set of COP's to try next. I can understand if it just plain missed all the time, but this it intermittent. Also, the only code I can get is a too lean on bank 1, so I replaced the 90's and the pvc valve. Now no codes but still in and out of missing. It ran perfect before the new head.
Chevrolet - Express :: 1996 - Code P0305 - Misfire In 5?
96 Chevy express 1500 V8-305. Have a P0305 code...Misfire on 5. Let me tell you everything I have done so nobody wastes their time.
I have, replaced the entire ignition system, "EVERYTHING" including a new distributor...Not the problem... I did a compression test...Not the problem...injector cleaning...not the problem.
When I moved the wire harness that goes into the "spyder" fuel injector system the engine smoothed out. I untaped the harness from around the plug and applied pressure to each wire the engine smoothed out. The back row 2nd pink wire seems to cause the most reaction.
My question is...Is it the wire harness or is it the injector system not reading plug? or could it be a combination of the 2? If I replace the wire harness might I still have to replace the injector system?
Ford F-150 - 1997-2003 :: 1999 5.4L - Idle / Running Rough Occasionally
I purchased a 1999 F-150 Lariat 4x4 automatic transmission about a year ago. When I did, the previous owner told me about an idle issue that he has occasionally. He said that the issue was with the IAC. He claimed that he had replaced it several times but "it was hard to get a good aftermarket IAC that actually works". He said he tried several, but it never fixed the issue. That sounds like he wasn't replacing the defective part to me, but I don't know. This is my first truck to ever purchase.
Fast forward a bit (about a year), and I have had intermittent issues with idle and running rough since I bought the truck. I don't drive the truck that often, but they are becoming more common, so I want to get things fixed now.
Issues:
1. When running at idle, especially in park, the idle seems to fluctuate and never stay consistent. The idle drops as soon as I put it into drive, and the truck jerks a bit when going into drive because the idle was too high in park. It has never died while at idle, however.
2. When driving, especially up a slight or moderate hill, the power seems low and the truck starts to ping and jerk. The only way I can avoid the jerking is to stomp on the accelerator and go into a lower gear. And even when doing that, I still can notice an ever so slight jerk.
3. This past week, it was rough for an entire 40 mile journey on the interstate. Slight ping the entire ride home. When I pulled into the driveway, it was jerking until I turned it off. I haven't tried to drive it sense.
Potential issues:
1. IAC - maybe the previous owner was right. Maybe I should replace it again, or clean it with some carb cleaner.
2. Cam Phasers - I saw some posts about this on the forum.
3. EGR valve - Also saw some posts about this.
4. Maybe even the transmission? It doesn't seem to have an issue going into or out of gear, though.
Ford F-150 (2004-2008) :: 2005 - Smoking White - Got Codes P0174 / P0300 / P0305 / P0306 / P0316?
05 2 wheel drive f150xl 4.2 l 135,000 miles. Smoking white out of exhaust. More at start up but doesn't go away. Turns a little blue. When parked at idle if I bring up the RPM's quick I will get a little puff of black in the white smoke. I can't smell or taste(when I touch my fingers to mouth) any anti freeze in the exhaust smoke but I live in Myrtle Beach and I have little if any anti freeze in the coolant. I flushed the motor, changed oil and filter and added a can of seafoam. I took the throttle body off and cleaned it. I also replaced the air filter because I went down a dirt road and hit a deep water hole. Dirt and mud got into the air filter and by passed it also. This was the reason for the engine flush also. I can't recall any smoke before this. Maybe a puff on start up from moisture not sure. Im going to buy a coil pack and plugs and start from there. I have never had this many codes.
P0174 Bank system 2 to lean P0300 random multipl Lean mil. Missfire detected P0305 random multiple Missfire detected cylinder 5 misfire P0306 cylinder 6 Missfire P0316 Missfire detected on start up first 1000 revolution