Ford F-150 - 1997-2003 :: 2002 V8 Running Rough - Codes PO353 And PO171
2002 F150 5.4 v8,,, I had troubles just over a month ago with a po305 code. i got the truck fixed with 2 new coils n some gaskets. I am having these po353 & po171 codes pop up now. The truck is running rough and I am curious to if its just another coil problem or if their is something I am overlooking or just don't know about?
View 1 RepliesAlero :: 2003 - Codes PO141 And PO171
03 Alero 2.2 with no maf sensor.
I have both codes 141, 171. I am trying to figure out if I should just change rear oxygen sensor or something else.
Ford F-150 - 1997-2003 :: 2002 4.6L Windsor Won't Stay Running - Codes PO171 And PO174
This truck has been running fine then as my son was getting off the interstate it started acting like it was running out of gas then died. I went to tow him in and it cranked right up and never had another problem for a week. Yesterday he drove 80 miles away when the same thing happened shortly after he got off the interstate. He replaced the fuel filter which it probably needed but still won't start and stay running. It cranks right up the immediately dies.
First time this happened it was throwing codes PO171 and PO174. Now it is not showing any DTC's at all and none pending. We see no frayed or bad wires and all vacuum hoses seem fine. He cleaned the MAF with no change in behavior.... If it were an outboard motor or some kind of boat I'd say the problem is in the ignition switch except it does run a very short time before dying. If I immediately try to restart it won't stay running. If I let it sit for a while then it will run for about a half minute.
Ford F-150 - 1997-2003 :: Truck Cranks For 3 - 4 Seconds Before It Finally Fires / PO171 And PO174 Codes
I have the notorious PO171 and PO174 codes on my 2003 5.4L that come back whenever I erase them. I cannot figure out the problem. Whenever I start the truck it cranks for 3-4 seconds before it finally fires, then rpm's are very low, then they finally pick up. I have noticed a loss in power as well. I have completed a full tune-up (spark plugs, coils, boots, filters, etc.)
I have checked the vacuum and PCV lines numerous times, I have yet to find a leak. MAF appears clean. I am running a K&N CAI setup. O2 sensors a good, replaced the gas cap. The only other problem I can see is a bad PCV valve? I hope it isn't a manifold gasket. The truck has been very well maintained and still looks brand-new throughout at 250,000 miles.
Ford 6.0L Power Stroke Diesel :: Rough Running / Truck Started Bucking And Hesitating At 45 MPH
Since our weather has returned to the cold side......my truck has started bucking and hesitating at 45 mph with EOT @ 130 and ECT @ 140. I can gas on it and it will clear up/let off and it would start up again once it gets below 50 mph. Once the deltas reach 150+ it clears up completely. Its never done this until this week. FICM volts are steady @ 48V. What is causing this or what to look for?
View 2 RepliesFord F-150 - 1997-2003 :: EGR Open All The Time / PO171 And PO174 Codes
Everything started with the typical lean bank 1 and bank 2 codes. I started at the basics change fuel filter PCV Hose & Valve clean the MAF changed air temp sensor(it was cheap). Still had same po171&po174 codes. Bought a obdll reader. After 3 weeks of nothing being accomplished I bit the bullet and took it to Ford for a diagnostic and they said it was definitely the intake gaskets.
I changed the gaskets and now this has gotten worse! I started the truck after reassembly and it ran like crap!
Checked everything and everywhere and could find nothing wrong. I then took off the vacuum line to the EGR and everything smoothed out. I didn't mess around and replaced the EGR the DPFE and the vacuum solenoid.
It still runs like crap especially at idle. I did the tests with my digital meter and found the vacuum solenoid is calling the EGR to be open all the time. I suspect that this would be the fault of the PCM? What should be my next course of action?
Ford F-150 - 1997-2003 :: 2001 5.4L Throwing Codes PO135 / PO155 / PO174 And PO171
I have a 01 f150 7700 with a 5.4L and its throwing codes po135, po155, po174, and po171. Here is the history, last year had same code and found it was a bad ELLBOW on pcv hose, replaced and that fixed it, I also had a crack on egr valve and I replaced that too. This Jan truck was running bad in the morning and I traced it to a bad idle air controller, replaced it. I got a code and guy said I had a bad pcv valve so I replaced it.
About 3 weeks ago check engine light came back on with the 4 codes listed above, I replaced both front o2 sensors, 250,000 mile so I thought that was it but came back same code, I took it to a local mechanic and he said that the intake gaskets need replaced, but he call me later and said I had no leaks on the intake and that he did find another vac leak. He didn't charge me anything and sent me on my way.
I drove the truck about 50 miles and same codes back, so to recap I have cleaned mad sensor, replaced both front o2 sensors, a new egr valve, a new idle air control, pcv valve, pcv hose and ELLBOW, don't know what to look at next. Any clues?
Ford F-150 - 1997-2003 :: 2002 - Running Rough - PO316 And PO306 Codes
These are the code that keep spitting out. I have a 2002 f150 5.4L supercrewand it is running rough. I had this problem about 3 months back but i didnot get any codes from the computer i washed my truck a 1/2 day earlier, 2days later it went away. this time it has spit out 4 codes a po306/po307/po300/po316. the po307 and the po300 are gone, but the other two remain and it is still running rough 2days later. i had just washed my truck 30min. before, it started happening, is there water somewhere? My dad (long time mechanic) says use wire dry on the cops and it will go away. I have read other post on misfiring and I am still not sure what to do?
View 10 RepliesFord F-150 - 1997-2003 :: 1998 - Rough Running Truck When Accelerating
I have a 1998 F150 4.6 2wd regular cab with 255,000 miles on it. Lately it has had some problems. The first is that it will run really rough when under a load, meaning when I step on the gas. It runs smooth at idle and at cruise but when I step on the accelerator it bogs way down and almost shuts off. I have changed the spark plugs, spark plug wires, coil packs and fuel filter. Now I'm thinking maybe fuel pump?
The other issue is that when the truck is having to work a little harder (i.e. pulling a trailer or running in the summer with the AC on) it will start to run hot. I have changed the thermostat, flushed the coolant, cleaned out the radiator, etc. and it still does it. Could both of my issues be related to a fuel problem??
Ford F-150 - 1997-2003 :: Running Rough Under Light Acceleration / Codes P0300 And P0301
Just got a 98 f150 w/ 5.4 4x4 excab. It idles fine but under light accleration. It starts bucking and missing bad, if I step on it, it down shifts and accelerates fine. If I try to maintain one speed it misses bad. It is not throwing any codes right now. The check engine light did come on for like a minute but went back off before I could have it read. I hooked up a scanner just to see if any codes were stored and got p0300 and p0301. I am going to clean the MAF and check for vacuum leaks. I hear the rear plug and coils can get water in them causing similar problems.
View 8 RepliesFord F-150 - 1997-2003 :: 2002 Truck Started To Idle Very Rough - Codes PO308 And PO316
My truck started to idle very rough. I pulled the codes and I got po308 and po316. First I changed plug #8, the electrode was nearly gone. I have never seen a plug in worse shape. Replaced that plug and fired it up, it still idled rough and threw the same codes. Next I moved the #8 coil pack to the #1 location and vice-versa, still the rough idle and same codes. Then I moved the #8 injector to the #1 location same results. Finally I tested compression in the #8 cylinder and it read 32psi ( not good) everything else read 150 to 160 psi. Squirted some oil into #8 and no difference in compression.The truck is a 2002 with 184,000 miles, it burns a quart of oil every couple weeks but still is in perfect shape. Should I bite the bullet and invest in a remanufactured engine for 2500.00? I put one in my 97 f 150 a few years ago with no problems.
View 5 RepliesFord F-150 - 1997-2003 :: Truck Suddenly Started Running Rough / Too Many DTCs All At Once
I have a 2001 F150 4.6L auto. This truck suddenly started running rough. Cleared all codes and re-scanned after starting truck. The codes are as follows; P0135, P0155, P0443, P0740, P0743, P0758, P1451, P1460, P1747, and P1760.
My question is; is it normal to have this many DTCs come up at once? Could my PCM be faulty causing this problem? Can you swap a pcm from the same year truck with the same options without reprogramming?
Ford F-150 - 1997-2003 :: Truck Running Rough / Intake Manifold Gasket Blown
I have been having some issues with my 97 ford f150 4.6 liter, started out running rough, then hydrolocked with no serious damage, blown intake manifold gasket, fixed that, alternator over charging do to bad voltage regulator, fixed that. and airbag code 52, still working on that, as well as failure to connect when trying to do diagnostic scan. now I am wondering if the engine diagnostic is still even working. still running good just a very slight vibration when warms up. I am not getting any code. or my check engine light is not showing any codes. What I want to do is force a code. What would be the safest way to force a code or force engine light to give a code?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: E99 Stalling And Sometimes Running Rough - Codes P1280 And P1247
E99 Romps on start up and randomly dying. Bought this truck about 3 weeks ago. Previous owner mentioned he had issues with it getting hot and shutting off and not starting. Has new IPR, ICP and pigtail, I just put in a new fuel filter. Has 206k miles on it and is the 4R100.
The past two days after sitting all night I have been cycling the key twice and it hasn't done its romp. Typically when it does I can tap the pedal once and it goes away. This I could deal with but its started to die randomly while driving, never while cruising down the road. Its either just after starting it and rolling slowly or slowing down for a stop or to turn. When it dies, I can put it in neutral and it fires back up no problem. SES light usually comes on for about 10-15 seconds after but goes away.
Replaced the grey CPS that was in it with a dark grey one from RiffRaff Diesel. Got a Edge CTS2 to figure out the problem, the codes Im getting are P1280 and P1247.
The ICP pigtail they replaced they spliced on with butt connectors. I plan on pulling it to check for oil and make sure it does look new and redo the connections with solder then shrink wrap them.
I was told to check the IPR% under full throttle which I did and it never went higher than 36.7
The truck did start running rough around 45-50 mph and I did get a video of the ICP jumping around while cruising down the road.
Then I went through a drive through and the truck kind of hiccuped like it wanted to stall and the ICP went right to 725 PSI and idled up and stayed there until I started to leave.
Truck is pretty much stock, K&N air intake and muffler cut out and straight piped.
Here is a link to the videos I got :
e99 7.3 ICP fluctuation while driving - YouTube
e99 ICP steady at 725 PSI after acting like it wanted to stall. - YouTube
Ford Super Duty (1999-2016) :: 2004 F250 Truck Not Running Strong / Hesitating When Step On Gas Pedal
I have a 2004 f250 6.8L and recently I've notice the trick not running strong. Is hesitating when i step on the gas pedal. For example, I am driving on the feeder road and fixing to get on the freeway ramp, well i have to spent a bit harder on has pedal to gain speed, but it seems its struggling and I can hear muffler making like a flapping noise. Also when I am going between 40-65mph and I spent on it, the tricks kind of jerks and vibrates. Feels like its coming from transmission. I let go and step on it again and it goes away. What to check??
Miles : 96k
Year: 2004
No Check Engine Light
Ford 7.3L Power Stroke (1999-2003) :: Truck Running Rough And On Less Than 8 Cylinders
I had an HPOP line burst and soak the engine compartment with oil. I replaced the line and degreased the engine and rinsed it off. I started the truck and let it idle for 15 minutes or so before driving it. On the way home right after a shift it started chugging and running terribly. The check engine light was on as well. I limped it the mile or so home and shut it off. I restarted it and it runs just fine. I checked the DTC's with Forscan and there were a bunch of things that were mostly related to the HPOP and the MAT sensor that was shredded when the line blew. I left the hood open to dry out today and I'm hoping it is just some water in a connector. Does that sound plausible?
View 6 RepliesFord F-150 - 1997-2003 :: 1998 Truck Will Not Start Occasionally And Error Codes
I have been having odd problems with my truck for several weeks now and what the problem may be. Occasionally the truck will not start. This happens after it has been run for an errand or to church. The truck turns over but no ignition. Sometimes if I pump the gas pedal very quickly I can get it to start. Other times I have to sit and wait about 5 minutes. I have gotten the following two error codes - P1506=Cylinder Head Temp Sensor and P1299=Idle Air Control Overspeed Error. For two days the "check engine" light was on, but now it has gone out. I have searched for an answer to this problem on these boards and one possibility may be a vacuum leak. Is this the most likely? 1998 Triton 4.6 ....
View 3 RepliesFord - Explorer :: 2003 Truck Started And Running Rough - High Temp Low Oil Light Came On
2003 ford explorer 4.6L. This truck will start and run rough high temp low oil light come on and temp gauge is pegged hot. Oil gauge is fine though, checked oil its fine.
I checked coolant reservoir its ok.
If I shut truck off and restart it will run ok and rev like normal and then all of a sudden go into limp mode and will misfire etc...
What sensor seems to be the main culprit?cht sensor???
Ford F-150 - 1997-2003 :: 2002 Truck Running On 3 Cylinders
My aunt recently gave me her 02 f150 for free because it got flooded and she didnt want to fool with it. she said it ran great before it got flooded. I flushed everything. oil, gas, and tranny. I blew water out the cylinders and replaced the spark plugs. I took the fuel injectors out and cleaned and cycled some b12 threw them. The truck starts and gets spark to every cylinder and is only running on 3. I can pull 3 plug wires off and the idle does not change. Idk what it could be but dead cylinders. I am afraid I am going to have to find a new engine. I am going to do a compression check later this week when I have time. I am new to fords so if there is anything I should check...
View 2 Replies