Ford F-150 - 1997-2003 :: Misfire On 2 Cylinders 1 And 8
My 97 F-150 has 208,000 miles on the original engine. It started misfiring originally on just 2 cylinders, 1 and 8, after pulling the codes. I also get a P0420, catalyst system below threshhold bank code being thrown, but I think it is because of the misfires.
To remedy this I've done the following:
1. Spark plugs are relatively new and were changed completely a few months prior to issues.
2. Coil Packs were changed on both sides. Additionally, Cylinders 1 and 8 are on separate coil packs.
3. Spark Plug wires were changed
4. Did a resistance test on each fuel injector and they all passed.
None of this has worked. Am I missing something obvious? From my friends I've heard everything from my exhaust is plugged to I need to change all my injectors. Injectors are costly and I'm not even sure how to check if my exhaust is partially plugged, but it seemed to be flowing fine. Also, I pulled plug one since it was simple to get to and noticed it was slightly brown, like it had oil on it.
I got frustrated and continued driving my truck until the problem degenerated into severe misfiring and now I cannot get it started at all (Wrong move). I bought a car and haven't drove it since, and have it sitting behind my house. Now the cops want to tow it because the registration is has expired so I've decided to move it into my garage so I can work on it. Part of me wants to junk it, but I've put a lot of time, money, blood, sweat, tears, and curse words into this truck and am motivated to get it back up and running since the transmission and front suspension had been replaced recently.
What to do!?!?
1. Go to the Ford dealership and have them diagnose the issue and then try to fix it? (I have little confidence in them from the stories I've heard)
2. Pull the engine, tear it apart, and rebuild it?
3. Drop a used/rebuilt engine in?
4. Call me crazy and say junk the truck and buy a different one?
Currently leaning towards option 3...
Ford F-150 - 1997-2003 :: Error Codes - Misfire Detected On Cylinders 2 / 5 And 6
My wife and I received her father's 2002 F150 4.2 5 speed 2 wheel drive truck after his passing. He purchased new plug wires and wanted to replace them. So, this weekend I put in new plugs, plug wires, changed the air filter, and changed the oil and filter. Started up and ran really rough. Threw my code reader on after taking it around the block and found the following codes...
P0316 Misfire detected in first 1000 revs,
P0302 Cylinder 2 misfire,
P0305 Cylinder 5 misfire,
P0306 Cylinder 6 misfire.
New plugs were Motorcraft plugs, but had skinnier center compared to the ones that came out of truck.
Where do I start? What do I do? I am really confused as I have changed plugs and wires before and always had vehicle run better or same as before change.
Ford F-150 - 1997-2003 :: Stumbling A Lot - Throwing Misfire Codes On 1 / 8 / 4 And 3 Cylinders
Recently bought 98 f150 xlt 3 door 5speed 4x4 4.6l 230k miles for $1k was throwing misfire codes on 1,8,4,3 cylinders. Usually throws two cylinders at a time and never the same cylinders consecutively
Parts replaced:
coils...msd blaster
belden wire
motorcraft plugs...when i did these it ran perfect for a tank of fuel...18mpg no stumble
two cans seafoam through the tank
tank was dropped and drained
fuel filter
one can seafoam intake cleaner
3" exhaust from the Y pipe back
MAF cleaned
Previous owner said to have tested and cleaned injectors but I am not positive it was done... I don't think its mechanical because it wanders through the cylinders and when i changed the plugs it ran spot on. it gets worse the warmer the truck gets also.
injectors?
clogged small cats?
sensor?
Ford F-150 - 1997-2003 :: 2002 F150 5.4 - CEL Came On For Code P0174 - Misfire On 7 Of 8 Cylinders
So the past few weeks my truck has been sputtering a lot. It seems to do it more so in low RPMS but when I lay on the throttle I didn't really notice it. I haven't had time to look into the issue but yesterday the issue got drastically worse and the CEL finally came on. Registered P0174 as well as a number of other codes including misfires on 7 of the 8 cylinders.
So far I have replaced the fuel filter. Spark plugs are only a few months old. I didnt think it would make sense for all of the coil packs to go out at once so I was thinking either a fuel issue or vacuum leak. Why would it only spit out P0174 (Banks 2) and not show P0171 (Banks 1) along with it? Fuel pump? Vacuum leak? Where should I start? 2002 F150 5.4L...
Ford F-150 - 1997-2003 :: 2002 Truck Running On 3 Cylinders
My aunt recently gave me her 02 f150 for free because it got flooded and she didnt want to fool with it. she said it ran great before it got flooded. I flushed everything. oil, gas, and tranny. I blew water out the cylinders and replaced the spark plugs. I took the fuel injectors out and cleaned and cycled some b12 threw them. The truck starts and gets spark to every cylinder and is only running on 3. I can pull 3 plug wires off and the idle does not change. Idk what it could be but dead cylinders. I am afraid I am going to have to find a new engine. I am going to do a compression check later this week when I have time. I am new to fords so if there is anything I should check...
View 2 RepliesFord F-150 - 1997-2003 :: Two Cylinders Misfiring - No Fuel To Injectors
97 F150 4x4 XLT 5.4L... I had two cylinders misfiring, removed COP, injectors and plugs. Reinstalled all parts and reconnected all sensors. Now I am not getting fuel to the injectors. Double checked for disconnected wires and hoses, checked all fuses and relays, also the inertia switch. Fuel pump does not hum when key turned on. Tried hitting bottom of gas tank. My question is, before I pull the tank again, is there something under the hood I may be missing. It does get quite crowded at the rear of the motor.
View 6 RepliesFord F-150 - 1997-2003 :: 1999 - Engine Shutter / Not Firing On All Cylinders?
i have a 1999 F-150 2x4 witha 5.4 liter v-8 with 151,000 miles. Last week the truck began to run rough when i accelerated (ideled fine)and felt like it wasn't fireing on all cylinders and was puffing white smoke. A few minutes later the battery light came on and the truck lost all power and shut off. I replaced the battery and alternator and everything ran fine for a week. Now the issues have come back but i'm not sure the alternator and batter have gone bad again. What could be going on? Have the coils gone bad?
View 1 RepliesFord F-150 - 1997-2003 :: 4x4 And Low Range Light Come On And Off With Clicking Coming From Under Dash
I have a 97 f150 lariat 4.6L 150,000+ miles, and I am getting a lot of electrical things going wrong, been looking, and found sum kind of electric module could be the issue, except the problem are a bit dif then the ones listed. I am just wondering if it could be my issue. my problems are, 4x4 and low range light come on and off with clicking coming from under dash, daytime lights work here and there, air bag light flashes.
Then this morn my wife went to leave for work and there was a air leak hissing sound coming from the brake pedal area and that was b4 she started the truck, then she said when she got there that the heater stayed on after she shut it off and there was a beeping sound coming from the glove box. I am a general diy mechanic and dont know electrical very well, and i am at a loss.
My steering wheel seems like it is bout to fall off, and when making turns it seems to bind and not wanna turn, but when i try to pull on it, it seems sturdy but it will kinda flop if i go side to side or up and down with it.
Ford F-150 - 1997-2003 :: 1999 - When Engage 4Hi Dash Light Low Range Turns On But Not 4x4
I have a 99 F150 5.4 V8 4x4, My problem is when I engage 4Hi the dash light "low range" turns on but NOT the 4x4 light. Now if I go to 4Low the 4x4 light turns on(Low Range light stays on). So in essence the lights are backwards. In 4Hi it is not engaging 4 wheel drive. Also its a SOTF not electronic selector.
View 2 RepliesFord F-150 - 1997-2003 :: Transmission Range Sensor Replaced - Got Code P0705?
I have replaced the transmission Range sensor (with OEM) and it is adjusted correctly, however This did not clear the. Code P0705... I am stuck ....
View 1 RepliesGolf IV R32 :: Misfires In Low RPM Range / Stumbling And Just Not Firing On All Cylinders
Ok so I'm having weird issues with my big turbo R. I thought I was having misfires in low rpm range. Car was stumbling and just not firing on all cylinders ( just an expression but that's what it felt like) realized it was because of the esp. Ok no the main issue. Vacuum was sitting around 14hg. When I come up to a light or stop sign or just put in neutral while moving it revs it self ad vacuum will go to almost 0hg until I come to a full stop.
The rev is not a big rev only like 100-150 rpm increase. Also the throttle response is not there if I go to rev match down shift. Here's the weird part. If I unplug the Maf it runs super smooth 19-20hg vacuum amazing throttle response clutch chatter almost goes away. There are no cel with or without the Maf plugged in I have logs for both...
Ford F-150 - 1997-2003 :: 2001 V6 Head Gasket Leak Causing Water To Enter Into Cylinders And Oil Pan
Recently bought a 2001. In the process of reading about this engine I discovered there is a some what regular breakdown of head gaskets causing water to leak into cylinders and oil pan, all of which is serious.
Given the vehicle is 12 years old and has 89K miles it appears it is in the age and range of where this leakage can occur. Any knowledgeable engine rebuilders that are familiar with this issue on the 4.2 have any comments???
1. Can this issue be avoided by replacing head gaskets now rather than waiting for future failure???
2. Are there new and improved head gaskets for this motor???
3. Does the problem occur on both heads gaskets?
4. Is that all that needs to be done or are there other seals that need replacement???
Ford F-150 - 1997-2003 :: 2003 - Got Code U1262 - Random Misfire?
I have a 03 F150 with a bi-fuel 5.4 engine an it has 195000 miles. I have had trouble for some time now with misfires. I bought the truck in october of 2011 with 125000 miles and replaced all the coils and spark plugs because it was misfiring badly will running on CNG. It was fine on gasoline and never had any codes. After I replaced the plugs and coils it ran fine on CNG and gasoline.
This summer 2013 it began missing badly at highway speeds only when running on CNG. If I accelerated the miss would go away until I was light on the throttle again.I checked the misfire count and found the bad cylinder and replaced a coil. Then a day later same thing on another cylinder. I swapped a coil from another cylinder and problem went away for a day. Eventually I chased the misfire around all the cylinders on the engine until I had ended up either replacing a spark plug or swapping a coil on all the cylinders. And I still had a misfire. It seemed to be worse on days with temperatures above 90 degrees. Eventually I got it to stop misfiring.
So now 5 months later I am back again with a misfire. This time it is misfiring on both gasoline and CNG and under any throttle conditions, except coasting. I have no codes. And the misfire monitor is sending me around the engine again. I have replaced a spark plug in two cylinders and swapped 4 coils.
I'm ready to buy all new coils, but I want to be sure that it is not a waste of money since the old ones only have 70000 miles on them.
Two days ago I had the misfire monitor saying #4 in the evening and the next day without me having done any work on it it was saying #6. Later that same day it said #7 and I still hadn't done anything other than drive the truck.
I checked the connections at the firewall on the drivers side with the three large plugs that are held in with a 10mm bolt, they looked fine, no corrosion or burnt pins. I checked the connection at the ACFM which also looks good. I will check the connection at the PCM in the next day or so.
Some other problems that may be contributing:
1. I occasionally get a U1262 code (scp fault)
2. Sometimes when I check the misfire monitor it only shows 7 cylinders, sometime 9 cylinders. I am using an Innova 3160 scanner.
3. I have either a leaking valve cover gasket or leaking head gasket, because I have oil dripping from the rear bottom corner of the passenger side cylinder head right above the exhaust pipe.
Ford - Taurus :: 2000 - Check Engine Light Came One - Misfire In Cylinders 1 And 3
I have an old 2000 Ford Taurus that has been having some misfire issues. I replaced the wires and plugs about a year ago and hooray! it worked... until about a month ago when the check engine light came one. Misfire in cylinders 1 and 3... again. I ran some SeaFoam through and it did okay until this week, when the warning/flashing check engine light came back.
It is idling very hard (expected) and feels like it is trying to stall, even before the misfire came back (also to be expected??). So here is the question: is this a coil pack issue, or something more sinister (and expensive)?
Ford F-150 (2004-2008) :: Codes For Misfire On Cylinders 4 And 5 And Coil D Circuit Malfunction
I do not know the 5.4l 3v as well as my last 360ci dodge. It's a 2005 F-150 SuperCrew 4x4, got it cheap, and it's got issues. Got codes for misfire on cylinders 4 and 5 and Coil 'D' circuit malfunction. Obviously it has codes for limited power as well. was wondering how cylinder numbering goes and what coil is 'D'.
View 6 RepliesFord - Mountaineer :: 2004 - Buck / Shake And Idle Around 400 RPMs - Misfire On 3 Cylinders
I recently picked up a 2004 Mercury Mountaineer, 4.0 with 113,000 miles. OBD reader says misfire on 3 cylinders.. Installed new plug wires first.. nothing.. going to install plugs next when she is cold. Now, am I really looking at replacing the coil pack to end the misfire codes? She likes to buck and shake and idle around 400 rpms.. I know that is too low..
View 4 RepliesFord F-150 - 1997-2003 :: Misfire On 7 Cylinder
I have changed the COP and the injector as well as the spark plug. I am still having a misfire on #7 cylinder....
View 8 RepliesFord F-150 - 1997-2003 :: 1998 - Misfire With No CEL?
I have a 1998 F150 4.6 that has a misfire with no CEL. I have already tried the following: checked fuel pressure, change cam shaft sensors, changed coil, checked MAf seems ok, spark plugs and wires. On my scan tool it wont show any misfires when obviously its misfiring. When driving it will run good for about 10 seconds and then misses for about 10 seconds and it just keep going in this loop.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 Running Rough / Misfire On Cylinders
I have a buddy at work who has an 04 f350 6.0 that is running very rough. we put a scanner on it and disabled the injectors and 1,7,8 have no change. He checked the FICM voltage and is getting 48 volts on crank and run. He checked the wiring for anything loose or rubbed but nothing seems wrong.
View 14 Replies