Ford F-150 - 1997-2003 :: Electrical Plugs To Fuel Injectors Seemed Really Loose
When doing my last spark plug change I noticed that the electrical plugs to the fuel injectors seemed really loose. The plastic tabs on the harness plugs don't even lock onto the injector plug. Its actually amazing that they don't vibrate loose or stay electrically connected. The plugs are not cracked or damaged that I can see. Is this a problem? I feel that I should replace the plugs with something that has more of a positive "grip" to the FI plug....
View 2 RepliesFord Ranger / B-Series :: 2003 - Multiple / Random Cylinders Misfiring
I have a 2003 ford ranger edge with the 3.0l engine. It started acting up today so i brought it to get checked because the check engine light came on. Three codes where pulled p0300, p0306, and p0313. They were multiple/random cylinders misfiring, cylinder 6 misfire, and first misfire at 1000 rpm. I have replaced the plugs and coil and still have the trouble.
View 5 RepliesCelica :: 2003 GT Misfiring On 3 And 4 Cylinders With Codes
According to the OBDII, I have a misfire on #3 & #4 cylinders. Im getting codes PO300, PO303, PO304 and PO171.
View 2 RepliesFord Wiring/Electrical :: 1997 - Fuel Injectors Not Working?
I swapped a 4.9l into a 1997 F-350 that had a 5.8L originally, my issue is the fuel injectors are not working. I did my homework and got the harness that was with the engine out of a 1995 F-150 and also got the correct PCM to go along with my E4OD tranny that is in the F-350. It has spark and 60 plus PSI fuel pressure in the rail and will run with starting fluid shot in the throttle body. Both vehicles came with OBD I so should be compatible there. I do not have 12v to the injectors and obviously the NOID light shows no pulse either. Could be a ground but not sure where to look or what else could cause this.
View 14 RepliesFord Excursion :: 2000 - Cylinders 1 / 2 / 3 / 4 Misfiring?
2000 Excursion V10.
Recently cylinders 1,2,3,4 wend dead on my wife's Excursion. I searched here for a pin out diagram so I can check all the wires from the coils to the PCM. I changed the coils on those 4 cylinders with no change and then swapped them with the coils on the left side of the engine. the problem stays on those 4 cylinders. Any link to pin out the wire harness for the coils to the PCM
Ford 7.3L Power Stroke (1999-2003) :: Injectors Clacking / Engine Feels Like Running Out Of Fuel
Engine felt like it was running out fuel, injectors were clacking. I got home put on AE and it has a low high open on the code reading. took valve cover off and plug came out. I did the quarter modification.
Anyway took the truck out a few days later truck drove ok when cold then after about an hour it lost power again and started clacking until it died out. I had to stop and let it cool off about 10 times before i made it home. I changed ICP sensor. took it out for ride and about ten minutes later same thing. I have to let oil temp get down to 165 before i can drive it again.
When i first drive it Icp pressure is about 500 at idle and 2650 at full throttle, that is until it starts clacking again and losing power then the engine wont take any throttle..and ICP duty cycle is at 26%... Would bad IPR do this??
Ford F-150 - 1997-2003 :: Misfire On 2 Cylinders 1 And 8
My 97 F-150 has 208,000 miles on the original engine. It started misfiring originally on just 2 cylinders, 1 and 8, after pulling the codes. I also get a P0420, catalyst system below threshhold bank code being thrown, but I think it is because of the misfires.
To remedy this I've done the following:
1. Spark plugs are relatively new and were changed completely a few months prior to issues.
2. Coil Packs were changed on both sides. Additionally, Cylinders 1 and 8 are on separate coil packs.
3. Spark Plug wires were changed
4. Did a resistance test on each fuel injector and they all passed.
None of this has worked. Am I missing something obvious? From my friends I've heard everything from my exhaust is plugged to I need to change all my injectors. Injectors are costly and I'm not even sure how to check if my exhaust is partially plugged, but it seemed to be flowing fine. Also, I pulled plug one since it was simple to get to and noticed it was slightly brown, like it had oil on it.
I got frustrated and continued driving my truck until the problem degenerated into severe misfiring and now I cannot get it started at all (Wrong move). I bought a car and haven't drove it since, and have it sitting behind my house. Now the cops want to tow it because the registration is has expired so I've decided to move it into my garage so I can work on it. Part of me wants to junk it, but I've put a lot of time, money, blood, sweat, tears, and curse words into this truck and am motivated to get it back up and running since the transmission and front suspension had been replaced recently.
What to do!?!?
1. Go to the Ford dealership and have them diagnose the issue and then try to fix it? (I have little confidence in them from the stories I've heard)
2. Pull the engine, tear it apart, and rebuild it?
3. Drop a used/rebuilt engine in?
4. Call me crazy and say junk the truck and buy a different one?
Currently leaning towards option 3...
Ford F-150 - 1997-2003 :: Misfire In Cylinders 1 And 8 Mostly In 50 - 60 Mph Range
I started out with misfires in cylinders 1 and 7. Replaced all spark plugs (used autolites, i know i know). While replacing them I found that the boot on coil 8 was beat up with a chunk missing. It was working before I replaced plugs. After I changed everything out the 8th quit working completely and I still had a miss in cylinder 1.
Replaced coils on both of those and put a new wire connector on for 8th cylinder because it no longer clicked in correctly anymore. Truck runs infinitely better than it did prior to this, but according to OBD2 I still have misfires in 1 and 8.
Mostly in the 50-60mph range. What else could be causing this??? Injector maybe or is there some other sensor or timing problem? My dad has a compression test kit, but he lives several hours away so I can't just get to that right away.
Ford Ranger / B-Series :: 2003 - Missing On 3 Cylinders Randomly / Lean Fuel
2003 Ranger (4.0 L-2wd)...
Codes - random misfire and cylinder banks 1, 2, 3, reads out lean fuel
Will be checking out injectors and rail pressure, however, trouble shooting in general for this issue.
Ford F-150 - 1997-2003 :: 2002 Truck Running On 3 Cylinders
My aunt recently gave me her 02 f150 for free because it got flooded and she didnt want to fool with it. she said it ran great before it got flooded. I flushed everything. oil, gas, and tranny. I blew water out the cylinders and replaced the spark plugs. I took the fuel injectors out and cleaned and cycled some b12 threw them. The truck starts and gets spark to every cylinder and is only running on 3. I can pull 3 plug wires off and the idle does not change. Idk what it could be but dead cylinders. I am afraid I am going to have to find a new engine. I am going to do a compression check later this week when I have time. I am new to fords so if there is anything I should check...
View 2 RepliesFord 6.7L Power Stroke Diesel :: 2014 F350 - Two Cylinders Misfiring
2014 F350 6.7... The truck has only 30000 miles on it. I was driving uphill and the engine just quit, but fired up right away after with engine check. On idling run at 500-700 rpm , no power, clicking noise , sometimes shaking. Took to the closest dealer right away, they don't know what is it, but they want to rake of the engine . This truck is not under any warranty. This is my first diesel truck, didn't expect anything like this....
View 4 RepliesFord Super Duty (1999-2016) :: F250 V10 - 2 Misfiring Cylinders
I just bought a 99 F250 Super Duty with the V10. When I bought it, I knew it had 2 misfiring cylinders (4 and 10) because it was throwing P0304 and P0310 (only 2 codes), but wasn't concerned as I've had to take care of my wife's Escape with it's misfiring cylinders. I replaced the 2 coils and replaced the plugs with Motorcraft plugs from O'Reilly's, cleared the codes and she ran fine for a couple of days. Now I'm getting an intermittent misfire, it's only occasionally throwing a pending code of P0300 which is "Multiple Random Misfire".
I'm fairly certain it's an issue on the electrical side because if it were an issue with the injector or injectors it would be constant regardless of RPM... right? As it is now, it basically does it between 55-65 while in overdrive trying to pull a hill or slightly accelerate. Once it's shifted out and the RPMs go up to 2k+ it runs like a champ... and it kills my fuel economy. The way it's behaving is just like when a coil is bad, but it's saying it's not identifying a specific cylinder (saying it's multiple) and it doesn't always do it (about 60% of the time).
I checked the MAF and it's very clean (looks almost new), checked the vacuum lines (those I found without a manual) and couldn't find any leaks and when I changed the plugs all the plug wells were dry.
Ford Super Duty (1999-2016) :: 2011- Misfiring On All Cylinders?
SO this truck came into the shop yesterday with a really bad misfire. pulled the codes and got a misfire codes for cylinders 1-6 and also p1450 (unable to bleed fuel tank vacuum) and p068a (pcm/ecm power relay de-energized too early) i found a TSB related to the issue, TSB 10-25-7 i did as the tsb told me to do and pulled valve covers to check out the rocker shaft rollers and inspect for any signs of surface deformation or fatigue. they were fine on both sides.: ive got spark in all cylinders. fuel pressure was right around 55-60 the gauge was fluctuating pretty good. checked for bad fuel or water in fuel ect. fuel seems to be good. pulled O2s incase of plugged cats still ran like crap.
View 13 RepliesFord F-150 - 1997-2003 :: Error Codes - Misfire Detected On Cylinders 2 / 5 And 6
My wife and I received her father's 2002 F150 4.2 5 speed 2 wheel drive truck after his passing. He purchased new plug wires and wanted to replace them. So, this weekend I put in new plugs, plug wires, changed the air filter, and changed the oil and filter. Started up and ran really rough. Threw my code reader on after taking it around the block and found the following codes...
P0316 Misfire detected in first 1000 revs,
P0302 Cylinder 2 misfire,
P0305 Cylinder 5 misfire,
P0306 Cylinder 6 misfire.
New plugs were Motorcraft plugs, but had skinnier center compared to the ones that came out of truck.
Where do I start? What do I do? I am really confused as I have changed plugs and wires before and always had vehicle run better or same as before change.
Ford F-150 - 1997-2003 :: 1999 - Engine Shutter / Not Firing On All Cylinders?
i have a 1999 F-150 2x4 witha 5.4 liter v-8 with 151,000 miles. Last week the truck began to run rough when i accelerated (ideled fine)and felt like it wasn't fireing on all cylinders and was puffing white smoke. A few minutes later the battery light came on and the truck lost all power and shut off. I replaced the battery and alternator and everything ran fine for a week. Now the issues have come back but i'm not sure the alternator and batter have gone bad again. What could be going on? Have the coils gone bad?
View 1 RepliesFord F-150 - 1997-2003 :: Stumbling A Lot - Throwing Misfire Codes On 1 / 8 / 4 And 3 Cylinders
Recently bought 98 f150 xlt 3 door 5speed 4x4 4.6l 230k miles for $1k was throwing misfire codes on 1,8,4,3 cylinders. Usually throws two cylinders at a time and never the same cylinders consecutively
Parts replaced:
coils...msd blaster
belden wire
motorcraft plugs...when i did these it ran perfect for a tank of fuel...18mpg no stumble
two cans seafoam through the tank
tank was dropped and drained
fuel filter
one can seafoam intake cleaner
3" exhaust from the Y pipe back
MAF cleaned
Previous owner said to have tested and cleaned injectors but I am not positive it was done... I don't think its mechanical because it wanders through the cylinders and when i changed the plugs it ran spot on. it gets worse the warmer the truck gets also.
injectors?
clogged small cats?
sensor?
Ford F-150 - 1997-2003 :: Misfiring Cylinder 3 And 8
Trucks throwing codes for cylinder 3 and 8 misfire. I pulled the plugs and both were covered in oil and cylinder 8s electrode was literally gone. so I replaced the plugs and within 5 miles it was missing again. so I replaced all plugs, all wires and coil packs. cylinder 8 plug had fouled out. Its a 4.6l 99. I have a mild exhaust leak where the manifold connects to the downpipe. but not bad enough I feel it should matter. it runs rough until about 3k rpm and then it kinda straightens out.
View 14 RepliesFord Super Duty (1999-2016) :: 2009 F250 5.4L - 2 Misfiring Cylinders
I have a 2009 f250 with 5.4l 3v. have had the truck only about 6 months. it started missing about a month after I got it. I replaced all 8 cops and all 8 sp. The truck ran excellent until 11/29, then I got a cel and the truck started running really bad. Found 3 misfiring cylinders. Changed all 3 cops again and that did nothing. Pulled the injectors and found 2 of them were clogged, replaced those also. Still no change was told by someone that the ecm/cpu may need to be reset, did that also. Still no change. There are no codes present but still has the multiple misfires.
View 9 RepliesFord F-150 - 1997-2003 :: 2002 F150 5.4 - CEL Came On For Code P0174 - Misfire On 7 Of 8 Cylinders
So the past few weeks my truck has been sputtering a lot. It seems to do it more so in low RPMS but when I lay on the throttle I didn't really notice it. I haven't had time to look into the issue but yesterday the issue got drastically worse and the CEL finally came on. Registered P0174 as well as a number of other codes including misfires on 7 of the 8 cylinders.
So far I have replaced the fuel filter. Spark plugs are only a few months old. I didnt think it would make sense for all of the coil packs to go out at once so I was thinking either a fuel issue or vacuum leak. Why would it only spit out P0174 (Banks 2) and not show P0171 (Banks 1) along with it? Fuel pump? Vacuum leak? Where should I start? 2002 F150 5.4L...