Golf/GTI VI :: Getting Misfires On All Cylinders
So I have never worked on the 2.5 before, I have an 01 A4 1.8T so I am used to VAG products though. The other day my neighbor had a CEL light, when I read the code it was a misfire in cylinder 2. Since it was a single cylinder I told him it was most likely a coil pack but asked if he had ever done plugs. He bought the car with around 60k and it now has 90k but he didn't think they were ever done. So I suggested swapping them out with the new coil pack. So he bought a (5) plugs and (3) coils since that is all they had local. Initially he just replaced the one coil and said the car was running great. Then when he had time he threw the new plugs in (Autolite Iridium don't recall #) and put the other coils in. After doing this the car went into limp mode and is showing random misfires in all cylinders. He pulled one of the new plugs and noticed that the dimensions of the plug appear different than the OEM plug.
The OEM plug has a longer threaded section so it would project into the cylinder further and the insulator on the new plug appears to have several rubber seals on it. Since he is getting misfires on all cylinders I would think it is plug related especially since the plugs are dimensionaly different, but he even checked the manufacturers website and they say these are a direct replacement. Did they change the plug design or is this a known issue with some cross references?
Golf IV R32 :: Random Misfires On Cylinders 4 / 5 And 6
I am getting random misfires on cylinders 4, 5, and 6. Mostly on 6, less on 5, and even less on 4. Cylinders 1-2-3 show ZERO misfires. I am using vag-com to monitor these. Mostly doing it on idle, cruise seems fine but occasionally when shifting I feel it when engaging the next gear. It doesn't buck but I feel a little hesitation. Cruising and accelerating I do not feel it. Its very strange. A couple times during extended idling I have even gotten a flashing CEL. Fuel mileage has been pretty bad ever since I got the car in December. Average tank gets me 250-270.
I tried swapping coils with 123, and the problem stayed on 456. Coils are all new since I got the car. Plugs are fairly new (under 5K) and I pulled a couple to check, they looked fine and gap was about .028. I might try a new set but my gut is telling me the problem is some where else. I would like to verify/test grounds but I don't know where the harness grounds out.
I also want to get a vacuum gauge on the FPR, or check fuel pressure at idle. I replaced one cracked vacuum line, i am thinning there might be others since there seems to be miles of vacuum line on MK4's. Also have a new fuel filter to install, mine appears to be OEM and the car has 97K.
Golf IV R32 :: Code For Misfires In Cylinders 1 And 2
My girlfriend's MkV Jetta 2.0T is throwing a code for misfires in Cylinders 1 and 2. I've already switched out the plugs and coilpacks with no change. I'm going to try re-positioning the coilpacks to see if the code follows. In doing some research, someone mentioned that it could be fouling on the injectors, which led me to BG44K. She has >215K miles. I figure she's gotta have some fouling that could be cleaned up. I have ~110K miles on my R32 - I figure it wouldn't hurt to do some cleaning in my own car.
View 4 RepliesGolf/GTI VI :: 2013 - Recurring Misfires On All 5 Cylinders
I'm getting random misfires on all 5 cylinders on my 2013 2.5L with ~4200miles. Sometimes the CEL will stay on other times it just flashes and goes away. I've gone to multiple dealers and none of them has done anything but clear the codes because "we couldn't replicate the issue," or "It's just rev hang/drive by wire."
What are the known causes of a brand new car misfiring? And what should I have VW look at?
When I mentioned that our family has a 2007 Eos all three dealers were chomping at the bit for me to bring it in for recalls I didn't even know about. This really rubbed me the wrong way. I've got one car that I KNOW is malfunctioning that VW won't do any work on, but the other VW is volunteering to work on!
I've got another appointment set for tomorrow after I get off work. How to push the right buttons or say the right words?
Golf IV / Jetta IV :: Multiple Random Misfires In All 4 Cylinders Came Up / Idle And Boost
I have a mk4 1.8t Gti. Recently I have been having issues with idle and boost. I read the codes and multiple random misfires in all 4 cylinders came up, idle control and the crank, knock, and o2 sensor came up. Shows that system is running to lean as well. I changed the spark plugs and wires, check the coil packs they where done about 1k miles so I expect them to be perfectly fine. When I clear the codes it idles below 9-8k rpms. I also noticed the breather hose coming out of the valve cover into the EGT has a hole melted into it, could this cause any of my issues?
View 2 RepliesPassat (B5) :: 2001 - Not Firing On All Cylinders - EPC Light On
I bought a 01 passat with a bad turbo I drove it home as I was getting home the STOP low oil pressure light came on and I parked it the engine had a lifter rattle but not knocking I went to start next day and Have no fire on first two cylinders (only two I checked), where to start? I pulled coil pack/plug tube out and hooked a plug in to check fire on first 2 cylinders got no spark....
View 1 RepliesNissan :: 1986 - Stumbling Like Running On 3 Cylinders When Started Cold
My 1986 Nissan 300ZX Turbo has 60,000 careful miles on the odometer. It began stumbling, like running on 3 cylinders, when started cold. Time of day and moisture make no difference. New Cold Start and Air Flow Sensors have worked a little, but it still has the stumbles about half the time when started cold.
View 5 Replies3000GT/Stealth :: Cylinders 3 And 6 Not Firing - No Voltage To Coil
97 SL ATX - Not firing on cylinders 3 and 6; no voltage to that coil.
I've checked:
Plugs
Wires
Coils
PTU
ECU
Timing
So I guess the CAS is the next best guess. So where exactly IS the CAS...and how do i test it? Also, where is the timing mark on the crank pulley? Cams are all aligned but I didn't see a mark for the crank and don't know where I should be looking.
Ford F-150 - 1997-2003 :: Stumbling A Lot - Throwing Misfire Codes On 1 / 8 / 4 And 3 Cylinders
Recently bought 98 f150 xlt 3 door 5speed 4x4 4.6l 230k miles for $1k was throwing misfire codes on 1,8,4,3 cylinders. Usually throws two cylinders at a time and never the same cylinders consecutively
Parts replaced:
coils...msd blaster
belden wire
motorcraft plugs...when i did these it ran perfect for a tank of fuel...18mpg no stumble
two cans seafoam through the tank
tank was dropped and drained
fuel filter
one can seafoam intake cleaner
3" exhaust from the Y pipe back
MAF cleaned
Previous owner said to have tested and cleaned injectors but I am not positive it was done... I don't think its mechanical because it wanders through the cylinders and when i changed the plugs it ran spot on. it gets worse the warmer the truck gets also.
injectors?
clogged small cats?
sensor?
Dodge - Durango :: When Starting Seems Like Firing On 1 Or 2 Cylinders / Died When Give It A Little Gas
150K 2003 durango 4.7, ran like a top, backed in my driveway to eat lunch. Went to start and it sounded like it was firing on 1 or 2 cylinders give it a little gas and it died. Repeated 3 or 4 times now no fire at all. No check engine light at first now it flashes. About 30 miles with new fuel from a reputable local station tank was on reserve ( 0 miles on the overhead indicator ). All fuses are good . could it be a relay.....
View 2 RepliesFord Ranger / B-Series :: 1990 V6 3 Cylinders On Driver Side Not Firing
Is there something that would make the 3 cylinders on the drivers side of a 1990 2.9l not fire? I have spark to the plugs and pressure/fuel at the schrader valve on the fuel rail. The passenger side cylinders are firing fine and the engine runs (roughly) on these 3 cylinders. Truck was running just fine, then all of a sudden, drivers side is dead. Is there a fuse or something that controls these three fuel injectors?
View 1 RepliesFord Ranger / B-Series :: Coil Is Sending Spark But Cylinders 4 / 5 And 6 Not Firing
Al right i have a 94 ranger 4.0 4x4 auto 186k ... The truck has new bosch double plat plugs gaped .054, new wires, MAF, TPS, FPR, O2 sensors, ECTS and I checked the intake air charge sensor and is fine ....
My issue is cylinders 4,5 and 6 dont fire... the coil is sending a spark, i can pull the plugs one at a time and watch them fire (strong blue spark)... All fuel injectors do not leak and spray a perfect cone out of all 4 holes and noid light test is good ...
The truck runs like crap back firing and no power under 4k and i can pull off all 3 wires for bank one and it make no difference and when i unplug the injectors no more back fire....
Ford F-150 - 1997-2003 :: 1999 - Engine Shutter / Not Firing On All Cylinders?
i have a 1999 F-150 2x4 witha 5.4 liter v-8 with 151,000 miles. Last week the truck began to run rough when i accelerated (ideled fine)and felt like it wasn't fireing on all cylinders and was puffing white smoke. A few minutes later the battery light came on and the truck lost all power and shut off. I replaced the battery and alternator and everything ran fine for a week. Now the issues have come back but i'm not sure the alternator and batter have gone bad again. What could be going on? Have the coils gone bad?
View 1 RepliesElantra GD (2013+) :: Startup Clunk - Slow Combustion Or Back Firing In Two Cylinders
Last night when I started my car before heading home from work I noticed that the engine clunked a couple of times, as if it were slowly combustion or back firing in two cylinders. The car started up fine; however, I've never heard the engine do that before. I don't know if it is because it has been cold up here the last few days (-12C (10F) day time highs) or if there's something else wrong. My EGT has just under 60,000km (37,200mi).
View 2 RepliesPassat (B5) :: Random Misfires On All 4 Cylinders
OK. I have a 2005 Passat 1.8t fwd. Tiptronic. 105k
The symptoms i am having is random cylinder misfires on all 4 cylinders. I have scanned with vagcom multiple times and get the same codes. However, I have cleared the codes, and wen fpd a 60 mile drive on the turnpike. Not a single code. So everything is perfect as long as the car dissent have a chance to idle.
I have also driven the car while logging misfires and only get misfires at idle. Never while driving.
So much has been done to the car that is so hard to decide where to start. Ill try to go in order of events.
All this in the past 4 weeks by the way.
Took car to very experienced VW tech. Found out.timing was off by 3 degrees. So new timing belt, water pump and all. Started car, still had misfires. Noticed wetness on head gasket. And did a compression test. Very bad results. (I can't remember the numbers but they were way off from each other) So he removed the head. He said there was a crazy amount of carbon buildup in the combustion chamber. Everything was cleaned, head inspected for bent valves and everything looked perfect after cleaning. (this car has NEVER overheated by the way) He said it is very rare for a head gasket to fail on 1.8t's . So he did a leakdown test and turned out the piston rings were shot. So engine was rebuilt. All components cleaned of carbon, replaced all parts, bearings with new OEM parts. Pickup tube cleaned along with other oil lines. Turbo was inspected, and I was told it is on its way out but still has life. So that was let go for now. All reassembled and all hoses checked, combi valve cleaned, new k&n filter in stock airbox. So he told me the car is finished after all that. I was excited! Drove the car home 15 min drive, ran great. Parked in my driveway, put it in park and misfires came right back. Called him the next day and brought the car back. He looked over it and replaced the fuel pressure regulator with new. He said it seemed like a fuel starvation issue. Tested fuel pump and it was towards the low end of the proper operation value. So I had a high flow pump sitting at home brand new and I brought it down and put it in. Still misfires but a lot less than before. Also fuel filter was replaced. So next he disconnected the cat And found it was clogged. Replaced with my old Audi one, and it ran fine. And this is the first time the car idled good enough to get all the monitors set for emissions testing. So he was convinced it was fixed. Room it for a test drive and came back, parked And began misfiring again. So I was so sick of this thing at this point, I told him to replace the Turbo with brand new OEM unit. And it still misfires.
He swapped a known good throttle body into it and no difference. He also said that he started going around and unplugging sensors and the more sensors he unplugged, the better the car ran. He was curious whether the ECU was faulty. So he put an ECU from his Audi in it which had a ko4 file in it. He said it ran amazing!! So he modified an ECU from a stock Audi and that's what I am driving with now. Still same symptoms. But not as often. Also brand new bosch mass air sensor was installed as well. So this is as far as we have gotten with it and I am so sick of this car right now. But we are both determined to get this thing fixed! And after all the money I have just spent, I can't even get rid of it or I will lose a lot of money. It really sucks because I love the car and so does my wife. And out of the three 1.8t's that I own, I have never had any major issues like this.
Santa Fe (CM - 2007-12) :: 2008 - Misfires On All 6 Cylinders
Just replaced all 6 plugs after getting p0300-p0306 codes. Still getting all codes, always starting with p0305. Was told coil was bad cause the shop only was getting p0305, but I have all misfire codes. We have over 95k on it, have owned since 2008. Its the 2.7 in it.
View 11 RepliesGTI 337/20th Anniversary :: Misfires In Cylinders 2 And 4 One Or Two Times A Day
Okay vortex here's what's happening in my 20th. About a month or so ago a CMP sensor went out, so I replaced that with a OEM sensor, on my way home my car started to misfire. So I took it easy the rest of the way home. The next day I started my car up and there were no misfires, drove to school, still no misfires but the check engine light was still on from the night before, after school on my way to get the codes ran it started to misfire again but then it stopped a few min into the drive.
Ever since then it has misfired but not all the time but maybe 1- 2 times a day then it would stop misfiring after a few min/seconds. My and my friend did the coil pack test and all the coil packs were good, yesterday (10/14/10) I replaced my plugs with NGK BKR7E plugs gapped at .028, my car is chipped with unitronic stage 2 tunning and it still misfired. I am going to clear all the codes and restet my ECU, but can you till do that with a unitronic ecu?
Passat (B5) :: 2001 / 1.8T - Multiple Misfires On All Cylinders / Lean Air Code
I have a 2001 1.8T Passat. I bought it used recently and have had tons of problems. I have been getting a lean air code for some time now and I think I recently resolved that. I had to replace a few vacuum lines, MAF, exhaust flex pipe (it was broken), fuel filter and fuel pressure regulator. The car was still running bad and throwing a lean air code (Bank 1) so I finally changed the O2 sensor and I think that did the trick. Now every time I start the car I get misfires until is warms up. I get misfires on all cylinders along with the multiple misfire code.
View 5 RepliesTiguan :: Random Cylinder Misfires On All Cylinders With Rough Idle
I have 11 tiguan 2.0T. When I start it up is runs rough below 1200 rpm. The check engine light starts flashing. The codes are all 4 cylinders for random cylinder misfire. When I go drive it around the roughness calms down but doesn't go away and the idle will start jumping up and down. It goes to 1500 back to 800. Then 1700 back to 800. It had even hit 2400 once. I have changed the pcv about 2 months ago. I checked it and it looks fine. One place said maf. I cleaned it and no change. Running out of options.
View 2 Replies