Ford F-150 - 1997-2003 :: Truck Has Random Misfire Code
I was involved in a light accident over the weekend. I was hit in the rear by a Prius which didn't do body damage except for the 7 blade harness for my trailer towing. But, now the truck has a random misfire code. You can feel the truck jerk when you go up any grade. We changed the fuel filter and dumped in some cleaner already. One guy says its fuel and one thinks its coils. It is a 2003 F150 extended cab 5.4 with a nearly new motor. The truck has about 175xxx on it and I have had it for about 40xxx. I have not changed coils. We did check the inertia switch on the passenger side and it was not tripped.
View 2 RepliesFord F-150 - 1997-2003 :: Random Misfire Now Won't Start
I have a 1997 F-150 2WD 4.6L V-8 that began having random misfires as I would drive. I was planning on going out today to get the new plugs and coils however when I got off work and pulled into my drive something happened when I went to leave the truck wouldn't even crank it just made a clicking noise. The battery has full power (the radio ect. still works). I am hoping that the problem is with the coils and plugs but if not ...
View 5 RepliesFord F-150 - 1997-2003 :: 1999 - Random Misfire While Driving On The Bad Alternator
I have a 99 F150 4x4 with 5.4 Triton, 99xxx miles. I was towing my boat when the regulator in my alternator went bad. I drove the truck with the voltage being sporadic for about 10 miles until I could get to a parts store. While driving on the bad alternator, I started noticing a misfire. I replaced the alternator, battery and DPFE. I still have the misfire....but here is the kicker. The misfire only happens when the truck reaches operating temperature. Which, in my limited knowledge, eliminates a fouled plug, COP, bad injector and a vacuum leak. I've got no check engine light so I can't pull a code. The only thing I can think of is to clean the EGR?
View 10 RepliesChevrolet - Avalanche :: 2003 - P0300 Code / Multiple Or Random Misfire?
My 03 Chev Avalanche is giving me a P0300 code (multiple or random misfire). With no distributor or individual coil is this something I can fix myself or is it shop time?
View 6 RepliesFord F-150 - 1997-2003 :: ABS Light Comes On And Off At Random - Code C1185
My abs light comes on with the code above and im looking to fix it. No I don't want to buy a new abs module. Code C1185 - Car Forums and Automotive Chat the only thing i could find remotely close is from this link for a 2000 ford windstar. Need to just comfirm that there is a chance that resoldering the joints would work in fixing the problem that would be great. The light comes on and off at random. 2001 f-150 lariat 4x4.
View 2 RepliesDodge - Durango :: 2003 - Code P0300 Random Misfire / Engine Running Rough
Just started getting a p0300 random misfire code on the durango a couple days ago. pretty sure it isn't moisture related since it started on a nice sunny day. it was running pretty rough so it was obvious that it was misfiring. I changed the plugs since it was about time anyway, and they needed it and I cleared the codes. new plugs (put in the oem champion copper plugs) didn't make the problem go away. The engine still ran rough and the code came back. 2 of the plugs looked like they may have been fouling a little bit. they were a fair bit blacker than the rest of the plugs. I went ahead and changed the coils on those two cylinders and reset the codes again. Still runs rough and the p0300 came back. where do I go from here? I am not getting any specific cylinder codes so it makes sense to me that it isn't one or two cylinders not getting spark. 2003 durango 4.7 ....
View 6 RepliesFord F-150 - 1997-2003 :: Code P0306 - Cylinder 6 Misfire
So my 99 F-150, 4.2L started throwing a code a few weeks ago, P0306 #6 Cyl Misfire. This thing has got 238,000 and has been the most reliable commute vehicle I've owned.
Today I changed all the plugs and wires (they were due anyways) which didn't resolve the issue. After clearing the code, got about 3 miles out and it came back. Running SeaFoam through the system on this tank as well, but I'm leaning towards an EGR blockage like what is described here:
Sparky's Answers: 1999 Ford F150, P0306 Misfire Cylinder #6
I was about to buy a new coil pack but I'd rather not continue to throw parts at this, as I've read many others do with this same exact situation, only to end up with the same code. I've replaced the coil pack once already a few years ago when I lost a cylinder on the way to work.
Ford F-150 - 1997-2003 :: CEL Code P0301 / Misfire With Cylinder 1
My 97 F150 through a CEL Tuesday night P0301 so I picked up a new plug because it's cheap and simple, but that didn't do anything. Spark plug wires are about 3 months old, I also swapped injectors between 1 and 2, and misfire stayed with cylinder 1. It also gained a tap when the misfire started but only above idle, but it doesn't sound like a rod knock.
I also noticed if you unplug injector 1at idle it taps/knocks 3 or 4 times, however if you unplug any of the others it doesn't do that. I checked and I definitely have good spark from the plug. I plan on picking up a new compression tester tomorrow since mine never was returned. If you take the oil fill cap off it doesn't have any blow by at idle, however if you rev it you get a quick cloud out of it.
I thought about picking up a kit to check the injector pulse.
Ford F-150 - 1997-2003 :: Code PO304 - Cylinder 4 Misfire
I have a '98 F150 4X2 extended cab with a 4.2l with 233K on it. I have no problem with drivability when I drive 5 miles to work. However, a couple of weeks ago when I had to drive 15 miles to the liquor store to get what I needed (I live in a dry county) I got back into my truck, started it and drove of. It drove like crap like I lost a cylinder. Drove it back home those 15 miles, let it cool off, put my scanner on it and got a PO304 code and I think a PO174 (bank 2 lean) code. Went to the #4 cylinder and found the plug had loosened up.
Tightened it back up, cleared the codes, and went through my normal weekly routine of driving to work with no problem. Made a booze run the next weekend and the same thing happened. Limped back home and found another PO304 code. Found the plug to be tight and in good condition but changed all the plugs since they were cheap copper core and had 20K on them. The wires only have 20K on them, too. Installed platinum plugs, drove all week 5 miles to work and back just fine. Made another 15 mile run yesterday and the same crap happened all over again after I got out of the store and drove home.
Ford F-150 - 1997-2003 :: Random Interval Engine Stops With Short Delay To Restart - Code PO231
I have got the most aggravating electrical gremlin possible. For over a year now, the truck intermittently just dies. Mostly it happens about 2-3 mins after start (every couple weeks or so), then takes a couple of key offs, then back ons to restart. But it does restart and then runs fine for a time.... 2 weeks ago I was rollin' down the road and hit a pothole, and whammo, she died, and wouldn't restart. I thought, "great it was the intertia cut-off going bad." I had it towed to the shop where they did some diagnosis and told me it threw a PO231 code.
The tech then said he was doing the diagnostic manual directed test, and swapped out the fuel pump relay, and it started right up. New relay, out the door. A few days later on the way to work about 2 - 3 minutes after start, she dies again. I hang my head, say a curse word, and key it a couple times, and it starts back up and runs fine. Presently speaking she's back at the shop, but the owner, who's a straight up dude was loath to take her back, because it was running fine at the time.... I've got to figure this thing out before I drive it off a cliff.
Truck -- 2001 7700 XLT 5.4L 88K miles
Symptoms -- Random interval engine stops with short delay to restart, 1 hard bump engine stop with no restart. PO231 code (after the hard bump no restart). Didn't check it previously (wasn't aware there were "soft" codes).
Troubleshooting to date -- 1 new fuel pump, 1 new fuel pump relay.
Only things left are the inertia cut-off switch (which apparently don't go bad that often), and the wiring itself/connections to the different components....
Ford F-150 - 1997-2003 :: 1998 - Cylinder 1 Misfire / Code P0301
I have a 98 F150 4.2L with code P0301 Cylinder 1 Misfire.
This is what I have done so far. New plugs, coil pack, plug wires, TPS, EGR, EGR Vacuum control regualier, DMCP, canister, all of these parts are new and was bought from the ford place. Have taken the egr value, and egr value bracket off to see if carbon blockage was present, but it was clean. It was clean in the motor also. Have blown air through the metal tube that connects to the egr value and it come out the tail pipe very good, so no blockage their. Have cleaned throtle body and injectors. Have tested fuel injector with tester and it works correctly. Motor holder pressure. Have correct fuel pressure.
Do not have any vacuum leaks, it holds vacuum correctly. Crankshaft sensor is fine. Went throw 4 cans of break parts cleaner, spraying on intake while motor was running, motor did not idle up or change. I have done all this and it still shows code P0301, and it still skips. Here's the catch, if you unplug the vaccum off the egr the misfire goes away, or unplug the EGR vacuum control regulator it goes away, or if you unplug the DMCP sensor it goes away, it does not matter witch one you unplug, the misfire goes away.
I have had several different test done the the truck, but all the test only show that one code P0301, they do not show any other codes, or problem's with my truck.
Ford F-150 - 1997-2003 :: P0307 Fault Code - Misfire On Cylinder 7
I have a 2001 King Ranch F150, which has a 2004 Lincoln Navigator 5.4 DOHC Intech engine installed. The engine was installed in 2005 and had less that 100 miles on it. The engine now has approximately 95000 miles and I have recently gotten a P0307 fault-miss fire on # 7 cylinder. I have installed a new spark plug, COP, and fuel injector. The fault has returned. What is the cause of my problem?
View 1 RepliesFord F-150 - 1997-2003 :: 2002 - Cylinder Misfire And A Lean Code
My truck was running fine the past few days minus a cylinder misfire and a lean code the misfire was due to a coil pack being out no big deal on that part but yesterday on 7/30/13 my temp gauge turned off my truck wouldn't go below 1k rpms and then the over heating light came on. i drove the one mile home and turned it off an hour later i went back out to my truck to get to work and it refused to start.
I decided to just hold my foot down on the gas and crank it and it eventually started drove it to work with the same symptoms. now today its doing the same thing except now the truck is broke down in the parking lot at my job the engine is flooding cause i can smell it last night i changed the thermostat. I can get so that i can get my truck up in running its a 2002 f150 5.4L 4x4....
Ford F-150 - 1997-2003 :: CEL Code Signifying A Cylinder 3 Misfire - Shudder / Hesitation
I will add as many details as possible :
2000 f150 4x4 offroad package
5.4L with 131k on it
new Dorman intake manifold
new Global Automotive (Ebay) COPs
New Motorcraft spark plugs
About 1500 miles ago I started throwing a code signifying a cylinder 3 misfire. The truck would bog down real bad and then after 5-6 seconds of no power it would return to normal. I tried replacing the COP (both with new and then with one from another cylinder) and plugs but no resolution. So I talked to the local ford service manager and he said it sounded like intake manifold problems.
Replaced the intake manifold and no more codes were being thrown.
1500 miles later and today the truck started having a hesitation/shudder when I was sitting in a drive-thru. I put the truck in neutral and park and neither solved the issue. With the earlier issue, when I would put in neutral and increased rpm, the issue would resolve.
I pulled out of the drive-thru and the hesitation was consistent no matter what the rpm or speed. The truck feels almost sluggish and lacks power. The hesitation is like 2x/second. When accelerating its almost like the rpms and speed hesitate, jump, hesitate, jump.
Ford F-150 - 1997-2003 :: 2002 F150 5.4 - CEL Came On For Code P0174 - Misfire On 7 Of 8 Cylinders
So the past few weeks my truck has been sputtering a lot. It seems to do it more so in low RPMS but when I lay on the throttle I didn't really notice it. I haven't had time to look into the issue but yesterday the issue got drastically worse and the CEL finally came on. Registered P0174 as well as a number of other codes including misfires on 7 of the 8 cylinders.
So far I have replaced the fuel filter. Spark plugs are only a few months old. I didnt think it would make sense for all of the coil packs to go out at once so I was thinking either a fuel issue or vacuum leak. Why would it only spit out P0174 (Banks 2) and not show P0171 (Banks 1) along with it? Fuel pump? Vacuum leak? Where should I start? 2002 F150 5.4L...
Ford F-150 - 1997-2003 :: SES Light Went Off - Code For Misfire Detection Monitor Disabled
I had recently thrown a code for a 'misfire detection monitor disabled' , never did address the issue. But just the other day the service engine light went off, the light had been on all this time and now it's off. My question is, how do I know if the light is just burned out. Is there something safe I could do to make the light come back on just to see if the light is actually still works.
2000 f 150 4.2 v6 232,000 miles ....
Ford F-150 - 1997-2003 :: 1998 4.6L - Misfire On Cylinder 6 / Code P0171 And P0174
P0306 (ok #6 missfire) with P0171 & P0174 --- Do I chase electrical or fuel or both. Afraid to assume anything but probably would normally address the misfire electrical first.... Don't want to go down that 'primrose path' if others have been there first!
View 4 RepliesFord F-150 - 1997-2003 :: 1999 - Misfire / Running Rough - Code P0305 And P0174
Here is my situation : I have a F150 1999 4x4 ext cab with 326 000 km. A little while ago I got a P0401 code so I decide to clean the TB first and at the same time change plugs and wires since they were overdue. The same code came back and a misfire. Ordered EGR valve, DPFE sensor and selenoid. Realize that I had ordered crappy plugs by mistake. I change all plugs. Had to wait for the EGR valve and others to arrive. I drove the truck for a while since I did not have the time to change the valve and others, during that time the misfire did not come back. Yesterday I change the EGR and others. Today I get a truck that runs really rough and got new codes , P0305 and P0174. I'm really confused now on what should be my next step, should I change the coils, can a P0305 cause a P0174. Should I change vacuum hose going to the EGR , selenoid and DPFE.
View 12 RepliesChevrolet - Montecarlo :: 2003 - High RPM Random Misfire
Here's the deal with this car i just did head gasket, valve job, all new intake gaskets and spark plugs. Car idles fine and mid throttles fine but with high throttle it wont shift and flashes the random misfire light p0300 it seems to run out of power. I've heard everything from maf sensors to ignition coils and wires. i was just wonder a good place to start and good test to do. I have most testing equipment including scan tool so i can ride with it. o and all cylinders compression tested above 150.....
View 13 Replies