Ford Exhaust :: Exhaust Manifold Leak Due To Broken Rusted Bolts
I have a 97 Expedition with the 5.4 engine and 160k miles. Recently while having other work done I was told that I had an exhaust manifold leak due to broken rusted bolts.
View 3 RepliesFord F-150 - 1997-2003 :: F350 - Exhaust Manifold And Two Of Lower Intake Bolts Broken
I have a 97 f350 crew cab xl stock everything. 351 windsor in it I do believe. as of right now He is broken down pulled apart in my garage. Due to a much requested headgasket replacement. In any event long story short I got him all apart to discover that there was someone in it before me & had broken the infamous exhaust manifold bolts (5) and two of the lower intake bolts, (of course I've tried the correct route in removing these broken bolts/studs but again the year of the truck (1997) & its bone stock no way their moving...
So of course I tried the next best thing (on a budget) which is to drill them out, but I went to far into the exhaust manifold bolt holes, And now I believe that I've ruined the heads is this so? If so who knows where i can get a decent set of bolt on heads ready to go. yes this is my daily driver & since He's been down I've been going deeper in dept.
Ford 7.3L Power Stroke (1999-2003) :: Exhaust Manifold Bolts Broken?
Just bought a 03, the seller showed me a exhaust leak. I found a bolt broken off, flush with the head. Looked at the passenger side when I got home, that side leaks too, and found one broken off bolt there too. Question, are these easy to do? As in, I have extracted broken bolts before, but they where on my V10 and I could just weld nuts to them and they came right out.
View 14 RepliesFord F-150 - 1997-2003 :: Multiple Exhaust Manifold Studs Broken On Both Side / Codes P1131 And P1151
I have a 2000 with a 5.4 and 166K miles. It had multiple exhaust manifold studs broken on both sides. Now that thay is fixed, I am getting the p1131 and p1151 codes. The EGR tube was also replaced at the time of the manifold fix. I checked over all the tubes and electrical connectors to rule out something simple but did not find anything out of place. The intake manifold was replaced with a new Napa one less than 5K miles ago as well.
Could the leaky exhaust manifolds over time set the fuel trim level high and now that they are fixed, the ECM is thinking it is running too rich? Can the ECM be reset to zero? There is also a ticking/rattling noise when you accelerate that seems to be coming from the fuel injectors. I listened with the stethescope and they are the only things that sound like the noise I hear. Could these all be related?
Ford F-150 - 1997-2003 :: Passenger Side Exhaust Manifold Cracked
2003 F150 5.4 4x4 supercrew ,76k miles
Recently the passenger side exhaust manifold cracked on my truck. I bought this truck about two years ago with 58k on it and currently have 76k miles. I remember getting the carfax report and being relieved to see that it had exhaust manifold replaced in July of 2014 at 49K miles along with a new EGR tube. I called the shop that worked on the truck to see if he could confirm that both manifolds were replaced since carfax only said manifold & egr tube. The shop manager confirmed that both manifolds were replaced and he told me that they were most likely manifolds from napa according to the part number.
Now, my question is, what's the best brand to replace the manifolds with? Should I just go with OEM and spend the extra $130 per side? I know the manifolds are a common problem with these trucks but only lasting three years and 27K miles just seems ridiculous to me.
I'm hoping that when I get around to actually doing this that they wont be to bad because of how recently they were replaced. For now I just cleaned the area with a wire wheel and used the inferno metal repair. Seems to have done the job but I don't expect it to last long, just another month or two until I move to a place where I can actually work on my vehicles.
Ford 7.3L Power Stroke (1999-2003) :: Exhaust Leak At Passenger Side Up-pipe To Manifold - P1211 And P1280
I just finished installing a new turbo (shaft play and lots of oil in the compressor side), RR up-pipes, and T500 (250k and once had a very long crank to get the ICP up to start).
Anyway, except for another exhaust leak at the pass side up-pipe to manifold, it seemed to run okay but with lots of white smoke. I only have about 50 miles after the install, when it suddenly starting surging and made a lot of loud knocking noises. This then went away and came back again rather quickly. I was close to home, so I made back under power. I also received the two codes listed. My IPR is original, but two summers ago I installed the IPR re-seal kit. Everything on the IPR looked good when it came off for the T500.
After reading around, I saw that low fuel pressure / air in fuel can cause problems. I connected a pressure gauge to the pre-filter port on the filter housing, and got 40psi at idle. I then took a diesel shower and blew out the fuel line into the tank. After re-connecting it, the fuel pressure stayed the same but the engines idles much better, but still has blue smoke. It's the original fuel pump (to me anyway) and original fuel line connections.
I have about 3/4 tank, and no place to put it, so I'd need to run it out for the Hutch mod, or least to get in there and inspect. Would eliminating the Ford connections at the pump be worthwhile for now, and is 40psi at idle adequate? Wondering if it's time for a fuel pump?
Ford Super Duty (1999-2016) :: Broken Exhaust Manifold Bolts - Long Term Fix?
I've got the dreaded broken exhaust manifold studs on my 2004 F250 V10. I don't drive it much (just 50,000 miles in 10 years) and confess I've ignored the hissing for quite a while. Is there really a permanent fix for these broken studs? Or should I expect to be replacing broken studs every 2 or 3 years?
If there is a permanent fix what is it? Special studs? Special manifold? I want to keep this truck a long time and don't want to be replacing these studs every few years.
Ford F-150 - 1997-2003 :: Broken Exhaust Manifold Bolt Removal
I have a 1999 ford f150 4.6 engine and it has an exhaust leak but wondering what is the procedure to remove a broken bolt and the rest of the bolts on the manifold
View 2 RepliesFord F-150 (2004-2008) :: Manifold Exhaust Leak - Rusted Bolts
Truck has 107 thousand miles; had to take it in for an manifold exhaust leak. Mechanic said bolts are so rusted they break.
1) was there ever a ALERT from ford about these bolt's?
2) Thought i read ford had stainless bolts for this problem...
I've had F150's only since the mid 70's and this 04 has cost me more in repairs than ANY previous F150..
Ford Super Duty (1999-2016) :: 2008 F450 - Lost Both Turbos / Exhaust Manifold Bolts Broken
Our F-450 with 102000 miles lost both turbos also broken exhaust manifold bolts. This truck carries tools fuel tank and sometimes skid loader on trailer. Heard lots of bad things about 6.4 liter motor now first hand experience. Asked dealer if 6500.00 bill could be reduced since so close to 100000 mile warranty and was told nothing could be done. Can not afford to sell truck now also have two other Ford F-250s newest one 2012. Is there any other approach that could be taken to get some relief from this expense.
View 14 RepliesFord F-150 (2004-2008) :: Exhaust Manifold Leak On Passenger Side
2004 SCrew, FX4, 5.4 ... I had the dreaded exhaust manifold leak on the passenger side. After reading the horror stories of this repair and living in the rust belt I decided against fixing it myself. I took it to a local repair shop to have done. Initially the mechanic could see that the front 2 studs were snapped off (before even trying to remove them).
After a full day of fighting the studs (engine loose & lifted up) everything is out but the front 2 studs. the top one has about 1/2" exposed, but it is frozen in place (penetrate on it overnight). The biggest problem is the bottom stud. it is broken off about 1/8" below the surface of the head. The guy doesnt have a small enough right angle drill to get between the frame & head to attempt to drill it out. I will gladly go buy a drill for him to do this, as it will likely save me money if it will work to drill out the stud.
Need to get the 2 studs out, particularly the bottom one, or what right angle drill may fit in there?
Ford F-150 - 1997-2003 :: Possible Manifold Leak In Exhaust
So I think I have possible manifold leak in my exhaust and its because when the engine is super cold, and I do have a straight pipe, but it sounds like a tractor... until it warms up after few minutes, it goes away.
My exhaust manifolds are rusted to crap and stuff is falling off, paint or whatever there was on them.
Now I've looked at bunch of videos on UT to get a better understanding since everyone says the nuts and studs are hard to remove or snap.
Now my question to anyone who's done this in their garage; I've seen bunch of videos where the stud snaps flush, then he takes a nut, puts it over the hole, holds it up with needle pliers and uses a MIG to start welding it... stud to nut... then puts a wrench and off it goes.
Now, I'm not a pro welder or anything so is it possible to by accident weld the stud, nut into the head and then never ever be able to undo or take either one out?? or is the head or whatever made from different material that won't get welded to the nut or the stud??
Ford Super Duty (1999-2016) :: F250 - Exhaust Manifold Leak On Passenger Side
Should I attempt to replace the passenger side manifold with what I can get from Napa. I would rather pay 100 bucks for everything and do it myself. But, Im concerned about replacing the studs. From what I have read the studs seam to be the problems for most leaks on these vehicles. I have torque equip. and other tools to do the job. Just want others opinions about this project. How hard really is it? 1999 5.4L F250 SDuty....
View 14 RepliesFord Exhaust System :: Exhaust Leak At Manifold Where Donut Gasket Meets The Catalytic Converters
My truck just started running really loud when it's cold and the leak goes away when it warms up to operating temperature.I did a little bit of investigating and I have found where the leak is coming from at the end of the exhaust manifold where the donut gasket meets the catalytic converters. It appears that the bolts rotted that hold the system together at the gasket. What should I do to repair this? I don't really want to replace the whole manifold because I know I'll break a stud off in the engine because everything is pretty rusty down there. I even took some pictures of the problem....
View 3 RepliesChevrolet - Silverado1500 :: 2003 - Exhaust Fumes Malfunction - 3 Head Bolts On The Manifold Popped Off
I have a problem with exhaust fumes in my 2003 Silverado truck. Initially, 3 head bolts on the manifold were found to be popped off. After replacing the bolts, the exhaust fumes in the cab still existed. The truck has been evaluated by a Cherolet dealership and 2 independent garages who found no system exhaust leaks. Obviously, I am very frustrated and not sure what to do next or where to go.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Broken Exhaust Manifold Bolt
So I received my International bellowed up pipes from Riffraff and I figure I will start soaking all of the bolts with some aerokroil before I get started on monday and I see the very last bolt head near the up pipe is gone. The bolt is there but the head is gone and you can definitely see soot buildup everywhere near it. I don't know if I should order a new manifold for the passenger side and new bolts, order a driver and passenger side manifold and new bolts, or just order one set of new bolts and try to get take the passenger side manifold off and replace the one broken bolt.
View 4 RepliesFord 6.0L Power Stroke Diesel :: Cannot Get Exhaust Manifold Bolts Off
I can't get my exhaust manifold bolts off. They are in bad shape. The 10mm is too loose and 3/8 just rounds. I have had the torches on them too! Can the bolts be cut off with a torch?? Haven't broken any. Can't get the bolt heads to move. It's an 04, original manifolds. I am working the driver's side. I can't figure this one out. How to get this manifold off?
View 4 RepliesFord Super Duty (1999-2016) :: 2008 F450 - Driver Side Exhaust Manifold With A Cracked Abd Broken Bolt
I got a 08 ford f450 sd in the shop with a cracked abd broken bolt in the driver's side exhaust manifold, any tips tricks on getting it out,I have everything loose but I can't for the life of me get the egr cooler out of the way to access the top bolts to the manifold so I can replace the manifold, or a link to a service manual would be great.
View 3 RepliesFord F-150 (2004-2008) :: Passenger Side Exhaust Manifold Was Leaking
2005 Supercrew and my passenger side exhaust manifold was leaking. Son of a mother duck that was a joke to get removed. Front two studs broke off about 1/4" below the surface. Manifold is not cracked but putting a straight edge across it's out of plane at least a quarter inch.
Had planned on the dorman manifold but read some poor reviews about it cracking in less than a year and being warped out of the box. There is an ATP manifold with very few reviews but all good. Or just bite the bullet and do shorty headers? The driver's side looks a lot easier to access.
These trucks really weren't designed to be worked on after assembly were they? I had to invent new cuss words. Looks like Ford manifold is disco'd...