Ford Exhaust System :: Exhaust Leak - No Gasket Or Donut Ring In The Flange?
I tore it apart and there was no gasket or donut ring in the flange. Is there supposed to be a gasket or donut ring? I can feel the leak with my hand. I have retightened & it still "tick-ticks" real bad.
View 7 RepliesFord Super Duty (1999-2016) :: P0420 Code - Leak At The Joint Where Exhaust Manifold Meets Pipe Beside The Engine
I have a 2011 F350 CC long box 4x4, with a 6.2, 93,000 km on it. I periodically get a P0420. I clear it and sometimes it comes back in 10 or 20 KM and sometimes it comes back in a couple hundred km. Been doing this for about 800 KM.
Yesterday I got an exaust leak at the joint where the exaust manifold meets the pipe beside the engine. Checked close, bolts appear intact, leak is on the outboard side blowing towards the frame. Looks like a gasket or donut seal failed.
I am wondering if the catalytic converter was plugged or restrictive, would this cause the P0420 and could back pressure from a restricted catalyitic converter cause the gasket to blow?
Golf IV R32 :: Exhaust Manifold Gasket Leak?
Have to do a replacement and if so.. is removed the intake the only way to get at those stubs on the ex manifolds.
I thought it was the flex-pipe.. but after listening to the sound and getting an engine code for b1 s1 the leak has to be before the o2 senor for it to pop a code..
It sounds like a standard header leak from backing out bolts or a faulty gasket leak..
Ford Exhaust :: 2000 - Can Remove Catalytic Converter From The Exhaust System?
Long story, I'll try to make this short, 2000 E250 5.4L What would or could happen if the catalytic converter was removed from the exhaust system?
View 5 RepliesFord Exhaust System :: Exhaust Manifold Leaking / Louder Than Normal Knock When Accelerating
Leaking exhaust manifold? The truck has a much louder than normal "knock" when accelerating. At first I thought and had some bad fuel in the tank. I eliminated that with a full take of good fuel and some STP but the "knocking" continued. Then I thought that perhaps it wasn't firing on all cylinders but it felt like it had full power. I took it to my mechanic and he said it as a exhaust manifold leak. He said that he has never replaced the exhaust manifold but that it was a "nightmare" and expensive. He also said that it's not a safety issue but on the long run the leak would cause the truck not to pass its emission test. He said the problem was with rusted bolts that would be difficult to remove.
View 12 RepliesFord Exhaust :: Exhaust Manifold Leak Due To Broken Rusted Bolts
I have a 97 Expedition with the 5.4 engine and 160k miles. Recently while having other work done I was told that I had an exhaust manifold leak due to broken rusted bolts.
View 3 RepliesFord F-150 - 1997-2003 :: Exhaust Leak On Passenger Side / Broken Exhaust Manifold Bolts
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 RepliesFord Exhaust System :: 2003 V10 - Running Little Bit Rough / Exhaust Leak?
I just purchased a 2003 V10 with 270 000kms. The truck had had regular maintenance. It has an exhaust leak and runs a little bit rough. Could the exhaust leak cause the truck to run a little rough or am I dealing with another issue?
View 2 RepliesFord F-150 - 1997-2003 :: Exhaust Manifold Gasket Cracked - Ticking Sound?
If the exhaust manifold gasket is broke / cracked will it making a ticking sound?
View 5 RepliesFord Exhaust System :: CAT Delete / No Catalytic Convertor
i just bought a cherry bomb glass pack and an exhaust system from summit. I am considering running no catalytic convertor. Anything i should know? I know it wont pass inspection but my truck wont pass right now anyway. I am more concerned with loss of power, or worse gas millage....
View 4 RepliesFord Exhaust System :: Catalytic Converter Locations
I have a 2001 Ford F250 Diesel. I recently cut the 4 inch exhaust pipe right behind the end of the cab cutting off the muffler and I thought the catalytic converter as well. I was talking to another super duty owner and he said he thought there was another catalytic converter further up in the pipe. Is this true? If so, how far would would I have to cut it to cut it off. Would this make the truck any louder...wouldn't mind if it did.
View 6 RepliesYaris/Scion & Vitz :: Some Dark Residue Coming From Exhaust Manifold Gasket
I have a 2001 echo with 140000kms on it, nothing ever has gone wrong with it. But I now have what sounds like a exhaust leak. I cant find any holes in the pipe anywhere. There is some dark residue that looks like it is coming from the exhaust manifold gasket. I replaced this but the sound continues. Do i need to get the manifold completely out of there and plane the mating surface of the manifold smooth. It looks really pitted right now?
View 7 RepliesFord F-150 - 1997-2003 :: Possible Manifold Leak In Exhaust
So I think I have possible manifold leak in my exhaust and its because when the engine is super cold, and I do have a straight pipe, but it sounds like a tractor... until it warms up after few minutes, it goes away.
My exhaust manifolds are rusted to crap and stuff is falling off, paint or whatever there was on them.
Now I've looked at bunch of videos on UT to get a better understanding since everyone says the nuts and studs are hard to remove or snap.
Now my question to anyone who's done this in their garage; I've seen bunch of videos where the stud snaps flush, then he takes a nut, puts it over the hole, holds it up with needle pliers and uses a MIG to start welding it... stud to nut... then puts a wrench and off it goes.
Now, I'm not a pro welder or anything so is it possible to by accident weld the stud, nut into the head and then never ever be able to undo or take either one out?? or is the head or whatever made from different material that won't get welded to the nut or the stud??
Ford Exhaust System :: Catalytic Converter Failure - Engine Knocking Under Acceleration
What would cause both Cat converters to fail at 20,000 mi.? Mine went out and the back pressure caused the engine to knock under acceleration. Also blew out an injector and plug. Luckily it was under warranty but wonder what could caused it.
View 8 RepliesFord F-150 (2009-2014) :: Exhaust Leak At Manifold Collector?
I currently own a 2009 F-150 XLT, ext. cab, 4X4, 4.6l, 6R80 trans. Surprise, Surprise I have just developed an exhaust leak at the manifold collector. After some careful investigation, I separated the pipe from the manifold and the sealing surface is totally rotted away. I cleaned it up as best as I could and slathered some muffler cement inside the joint to seal the leak. It is about 80% better but will get worse again I'm sure.
I visited my local Ford dealer and talked to a friend I have working there and he said Ford has known about quality issues with manifolds for years and he was surprised that the manifolds lasted 70k miles.
I am hoping to use the truck as is through the winter and in the spring I am going to install these headers:JBA Headers - Reviews on JBA Cat4ward Exhaust Headers - Stainless, Ceramic & Chrome Finishes
This intake:K&N 63 Series AirCharger High Flow Cold Air Intake Kits Best Price & Reviews
This tuner:Bully Dog Triple Dog GT Tuner (49-State Legal) - Bully Dog GT Tuner Reviews on Gas Programs for Dodge, Chevy, Ford & Nissan Trucks
I already installed a Flowmaster American thunder catback exhaust system about a year ago...
Ford F-150 (2004-2008) :: Manifold Exhaust Leak - Rusted Bolts
Truck has 107 thousand miles; had to take it in for an manifold exhaust leak. Mechanic said bolts are so rusted they break.
1) was there ever a ALERT from ford about these bolt's?
2) Thought i read ford had stainless bolts for this problem...
I've had F150's only since the mid 70's and this 04 has cost me more in repairs than ANY previous F150..
Ford 7.3L Power Stroke (1999-2003) :: Oil Leak From Exhaust Manifold
I own a e1999 Ford F350 7.3 4x4 with a Garrett GTP38R turbo. I have been having issues with very little power and pulled an CEL of P0221. I know it's for the APS and have been trying to trouble shoot it as a new APS has not fixed the problem. However, while working on that I just noticed an oil leak appear. I tracked it down and can visibly see it leaking out the top of the passenger side exhaust manifold in two places. It is seeping out the top. Is oil supposed to even be running through here like that?
I recently replaced my up pipes with the newer style bellowed ones. While I had the turbo off I replaced all the o-rings top and bottom and did the EBPV delete on the pedestal. I have been having very little power and cannot the truck over 5-10 MPH and stays at low RPM's so I originally thought it was the leaky up pipes. Those were fixed along with fuel pressure checks which came back good. I then pulled the P0221 code finally. While I had the turbo off I inspected it and it did spin freely and had no side to side play in it.
What was unusual to me was there was a small pooling of oil in the turbo when I took it off. I know the CCV goes through here so some oil is normal. Also, when I was diagnosing the up pipe leak I could see a small amount of oil spraying out the blown donut gasket along with the exhaust gases. I don't think that is normal.
Is there an internal seal in the turbo that can go bad causing oil to spill into my exhaust and possibly leak at the exhaust manifold? Or do I have an internal oil leak from somewhere else?
Ford F-150 (2004-2008) :: Exhaust Manifold Leak On Passenger Side
2004 SCrew, FX4, 5.4 ... I had the dreaded exhaust manifold leak on the passenger side. After reading the horror stories of this repair and living in the rust belt I decided against fixing it myself. I took it to a local repair shop to have done. Initially the mechanic could see that the front 2 studs were snapped off (before even trying to remove them).
After a full day of fighting the studs (engine loose & lifted up) everything is out but the front 2 studs. the top one has about 1/2" exposed, but it is frozen in place (penetrate on it overnight). The biggest problem is the bottom stud. it is broken off about 1/8" below the surface of the head. The guy doesnt have a small enough right angle drill to get between the frame & head to attempt to drill it out. I will gladly go buy a drill for him to do this, as it will likely save me money if it will work to drill out the stud.
Need to get the 2 studs out, particularly the bottom one, or what right angle drill may fit in there?
Ford Excursion :: 2000 V10 - Oil Leak After Exhaust Manifold Stud Repair
2000 excursion, 4X4, V10
A few days after the job was completed I noticed that the top stud on the driver's side closest to the firewall has signs of oil leaking from inside the hole. This is a hole that I had to drill and insert an 8mm Heli-coil. I was very careful on the depth of the hole I drilled. I tried removing the bolt and placing JB Weld high temperature epoxy into the hole and reinstalled the bolt. I waited over 24 hours for the epoxy to cure and then I checked for leaks. The leak re-appeared but has slowed down quite a bit. I have a USB endoscope that I will be using to inspect the inside of the hole to see if I can see where the leak is actually coming from. I am in no position to replace the head but I will do whatever it takes to get the truck back into service.
After 7 days in my garage, I finally removed/replaced all 20 manifold studs. I had to cut off all of the nuts to remove the manifolds. I was able to remove 17 out of 20 studs by using a 6 inch pipe wrench and a lot of coaxing. 3 of the studs were already snapped off inside the head. I drilled out two and was able to get them tapped for a Heli-coil. The third stud I broke a 1/8" cobalt drill bit inside and it took 4 days to get enough of the hole drilled out to get a Heli-coil inserted.