Ford F-150 - 1997-2003 :: Exhaust Leak On Passenger Side / Broken Exhaust Manifold Bolts
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 RepliesFord F-150 (2004-2008) :: Manifold Exhaust Leak - Rusted Bolts
Truck has 107 thousand miles; had to take it in for an manifold exhaust leak. Mechanic said bolts are so rusted they break.
1) was there ever a ALERT from ford about these bolt's?
2) Thought i read ford had stainless bolts for this problem...
I've had F150's only since the mid 70's and this 04 has cost me more in repairs than ANY previous F150..
Ford 7.3L Power Stroke (1999-2003) :: Exhaust Manifold Bolts Broken?
Just bought a 03, the seller showed me a exhaust leak. I found a bolt broken off, flush with the head. Looked at the passenger side when I got home, that side leaks too, and found one broken off bolt there too. Question, are these easy to do? As in, I have extracted broken bolts before, but they where on my V10 and I could just weld nuts to them and they came right out.
View 14 RepliesFord F-150 - 1997-2003 :: F350 - Exhaust Manifold And Two Of Lower Intake Bolts Broken
I have a 97 f350 crew cab xl stock everything. 351 windsor in it I do believe. as of right now He is broken down pulled apart in my garage. Due to a much requested headgasket replacement. In any event long story short I got him all apart to discover that there was someone in it before me & had broken the infamous exhaust manifold bolts (5) and two of the lower intake bolts, (of course I've tried the correct route in removing these broken bolts/studs but again the year of the truck (1997) & its bone stock no way their moving...
So of course I tried the next best thing (on a budget) which is to drill them out, but I went to far into the exhaust manifold bolt holes, And now I believe that I've ruined the heads is this so? If so who knows where i can get a decent set of bolt on heads ready to go. yes this is my daily driver & since He's been down I've been going deeper in dept.
Ford Super Duty (1999-2016) :: Broken Exhaust Manifold Bolts - Long Term Fix?
I've got the dreaded broken exhaust manifold studs on my 2004 F250 V10. I don't drive it much (just 50,000 miles in 10 years) and confess I've ignored the hissing for quite a while. Is there really a permanent fix for these broken studs? Or should I expect to be replacing broken studs every 2 or 3 years?
If there is a permanent fix what is it? Special studs? Special manifold? I want to keep this truck a long time and don't want to be replacing these studs every few years.
Ford Super Duty (1999-2016) :: 2008 F450 - Lost Both Turbos / Exhaust Manifold Bolts Broken
Our F-450 with 102000 miles lost both turbos also broken exhaust manifold bolts. This truck carries tools fuel tank and sometimes skid loader on trailer. Heard lots of bad things about 6.4 liter motor now first hand experience. Asked dealer if 6500.00 bill could be reduced since so close to 100000 mile warranty and was told nothing could be done. Can not afford to sell truck now also have two other Ford F-250s newest one 2012. Is there any other approach that could be taken to get some relief from this expense.
View 14 RepliesFord Exhaust System :: Exhaust Leak At Manifold Where Donut Gasket Meets The Catalytic Converters
My truck just started running really loud when it's cold and the leak goes away when it warms up to operating temperature.I did a little bit of investigating and I have found where the leak is coming from at the end of the exhaust manifold where the donut gasket meets the catalytic converters. It appears that the bolts rotted that hold the system together at the gasket. What should I do to repair this? I don't really want to replace the whole manifold because I know I'll break a stud off in the engine because everything is pretty rusty down there. I even took some pictures of the problem....
View 3 RepliesFord 6.0L Power Stroke Diesel :: Cannot Get Exhaust Manifold Bolts Off
I can't get my exhaust manifold bolts off. They are in bad shape. The 10mm is too loose and 3/8 just rounds. I have had the torches on them too! Can the bolts be cut off with a torch?? Haven't broken any. Can't get the bolt heads to move. It's an 04, original manifolds. I am working the driver's side. I can't figure this one out. How to get this manifold off?
View 4 RepliesFord Super Duty (1999-2016) :: F350 V10 - Exhaust Manifold Bolts Breaking
Bolts breaking on the exhaust manifold. If so why isn't ford doing a recall on this problem I have a F350 V10 90K miles and 3 on the top drivers side are missing not sure on the passenger side. Is this a problem with all the ford engines I have never had this problem with any other truck or car I have owned.
View 5 RepliesFord Fuel System :: 1996 - Metal Line Coming From Exhaust Manifold To EGV Valve Rusted On Both Ends
What's the best way to changed a EGV valve on a 1996 Ranger? The metal line coming from the exhaust manifold to the EGV valve, is seriously rusted on both ends. It looks like if I don't heat the metal line, the line will just round out, what's the best way to tackle this job.
View 6 RepliesChevrolet - Silverado1500 :: 2003 - Exhaust Fumes Malfunction - 3 Head Bolts On The Manifold Popped Off
I have a problem with exhaust fumes in my 2003 Silverado truck. Initially, 3 head bolts on the manifold were found to be popped off. After replacing the bolts, the exhaust fumes in the cab still existed. The truck has been evaluated by a Cherolet dealership and 2 independent garages who found no system exhaust leaks. Obviously, I am very frustrated and not sure what to do next or where to go.
View 1 RepliesFord F-150 - 1997-2003 :: Broken Exhaust Manifold Bolt Removal
I have a 1999 ford f150 4.6 engine and it has an exhaust leak but wondering what is the procedure to remove a broken bolt and the rest of the bolts on the manifold
View 2 RepliesFord Ranger / B-Series :: Broken Bolt At Downpipe On Exhaust Manifold
This is for a Pontiac Vibe. I broke one of the bolts that connects the exhaust pipe to the exhaust manifold. Need to get some type of nut/bolt/spring that I could use to fix it. The bolt is sticking out of the flange about 3/4" if I had a long nut to screw onto that?...........
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Broken Exhaust Manifold Bolt
So I received my International bellowed up pipes from Riffraff and I figure I will start soaking all of the bolts with some aerokroil before I get started on monday and I see the very last bolt head near the up pipe is gone. The bolt is there but the head is gone and you can definitely see soot buildup everywhere near it. I don't know if I should order a new manifold for the passenger side and new bolts, order a driver and passenger side manifold and new bolts, or just order one set of new bolts and try to get take the passenger side manifold off and replace the one broken bolt.
View 4 RepliesFord F-150 - 1997-2003 :: Multiple Exhaust Manifold Studs Broken On Both Side / Codes P1131 And P1151
I have a 2000 with a 5.4 and 166K miles. It had multiple exhaust manifold studs broken on both sides. Now that thay is fixed, I am getting the p1131 and p1151 codes. The EGR tube was also replaced at the time of the manifold fix. I checked over all the tubes and electrical connectors to rule out something simple but did not find anything out of place. The intake manifold was replaced with a new Napa one less than 5K miles ago as well.
Could the leaky exhaust manifolds over time set the fuel trim level high and now that they are fixed, the ECM is thinking it is running too rich? Can the ECM be reset to zero? There is also a ticking/rattling noise when you accelerate that seems to be coming from the fuel injectors. I listened with the stethescope and they are the only things that sound like the noise I hear. Could these all be related?
Ford Exhaust System :: Exhaust Manifold Leaking / Louder Than Normal Knock When Accelerating
Leaking exhaust manifold? The truck has a much louder than normal "knock" when accelerating. At first I thought and had some bad fuel in the tank. I eliminated that with a full take of good fuel and some STP but the "knocking" continued. Then I thought that perhaps it wasn't firing on all cylinders but it felt like it had full power. I took it to my mechanic and he said it as a exhaust manifold leak. He said that he has never replaced the exhaust manifold but that it was a "nightmare" and expensive. He also said that it's not a safety issue but on the long run the leak would cause the truck not to pass its emission test. He said the problem was with rusted bolts that would be difficult to remove.
View 12 RepliesFord F-150 - 1997-2003 :: Possible Manifold Leak In Exhaust
So I think I have possible manifold leak in my exhaust and its because when the engine is super cold, and I do have a straight pipe, but it sounds like a tractor... until it warms up after few minutes, it goes away.
My exhaust manifolds are rusted to crap and stuff is falling off, paint or whatever there was on them.
Now I've looked at bunch of videos on UT to get a better understanding since everyone says the nuts and studs are hard to remove or snap.
Now my question to anyone who's done this in their garage; I've seen bunch of videos where the stud snaps flush, then he takes a nut, puts it over the hole, holds it up with needle pliers and uses a MIG to start welding it... stud to nut... then puts a wrench and off it goes.
Now, I'm not a pro welder or anything so is it possible to by accident weld the stud, nut into the head and then never ever be able to undo or take either one out?? or is the head or whatever made from different material that won't get welded to the nut or the stud??
Ford F-150 (2009-2014) :: Exhaust Leak At Manifold Collector?
I currently own a 2009 F-150 XLT, ext. cab, 4X4, 4.6l, 6R80 trans. Surprise, Surprise I have just developed an exhaust leak at the manifold collector. After some careful investigation, I separated the pipe from the manifold and the sealing surface is totally rotted away. I cleaned it up as best as I could and slathered some muffler cement inside the joint to seal the leak. It is about 80% better but will get worse again I'm sure.
I visited my local Ford dealer and talked to a friend I have working there and he said Ford has known about quality issues with manifolds for years and he was surprised that the manifolds lasted 70k miles.
I am hoping to use the truck as is through the winter and in the spring I am going to install these headers:JBA Headers - Reviews on JBA Cat4ward Exhaust Headers - Stainless, Ceramic & Chrome Finishes
This intake:K&N 63 Series AirCharger High Flow Cold Air Intake Kits Best Price & Reviews
This tuner:Bully Dog Triple Dog GT Tuner (49-State Legal) - Bully Dog GT Tuner Reviews on Gas Programs for Dodge, Chevy, Ford & Nissan Trucks
I already installed a Flowmaster American thunder catback exhaust system about a year ago...
Ford Super Duty (1999-2016) :: 2008 F450 - Driver Side Exhaust Manifold With A Cracked Abd Broken Bolt
I got a 08 ford f450 sd in the shop with a cracked abd broken bolt in the driver's side exhaust manifold, any tips tricks on getting it out,I have everything loose but I can't for the life of me get the egr cooler out of the way to access the top bolts to the manifold so I can replace the manifold, or a link to a service manual would be great.
View 3 Replies