Ford 7.3L Power Stroke (1999-2003) :: Exhaust Manifold Removal - 1 Bolt Stuck?
I managed to get the drivers side exhaust manifold and all of its bolts off no problem. On the passenger side I had 1 bolt head that was already broken and I have only 1 other that is still holding on for dear life. I've been soaking it in aerokroil for awhile now and no luck. I tried some PB blaster today because I am willing to try anything. I also tried heating up the bolt with a torch and some map gas but not sure if I am heating it up enough or not. Anyways, everything else has been going great, got the uppipes off and the valley, turbo and pedestal all cleaned up good. Just need to get the last whole bolt and broken bolt out so I can install the new manifolds. What I should try to remove the last 2 bolts. How hot should I get the bolt when trying to remove it? Or should I be heating the engine block?
View 12 RepliesFord 7.3L Power Stroke (1999-2003) :: Broke Off Bolt In Exhaust Manifold To Head
Well i had an exhaust leak on this F250 and so I started torquing the bolts on the manifold to the head. (45 ft.lbs) A couple were very loose so I was thinking "Great, this may fix my problem!"
My first mistake was probably the Harbor Freight Tools torque wrench.
I am on the driver side, second from the rear and then bang! I see a gaping hole where the bolt used to be. Bolt on the floor. I cant see up in the hole to the head, I think it broke flush with the head.
Ford 7.3L Power Stroke (1999-2003) :: Exhaust Manifold Bolts Broken?
Just bought a 03, the seller showed me a exhaust leak. I found a bolt broken off, flush with the head. Looked at the passenger side when I got home, that side leaks too, and found one broken off bolt there too. Question, are these easy to do? As in, I have extracted broken bolts before, but they where on my V10 and I could just weld nuts to them and they came right out.
View 14 RepliesFord F-150 - 1997-2003 :: Broken Exhaust Manifold Bolt Removal
I have a 1999 ford f150 4.6 engine and it has an exhaust leak but wondering what is the procedure to remove a broken bolt and the rest of the bolts on the manifold
View 2 RepliesFord Super Duty (1999-2016) :: 2008 F450 - Driver Side Exhaust Manifold With A Cracked Abd Broken Bolt
I got a 08 ford f450 sd in the shop with a cracked abd broken bolt in the driver's side exhaust manifold, any tips tricks on getting it out,I have everything loose but I can't for the life of me get the egr cooler out of the way to access the top bolts to the manifold so I can replace the manifold, or a link to a service manual would be great.
View 3 RepliesFord Ranger / B-Series :: Broken Bolt At Downpipe On Exhaust Manifold
This is for a Pontiac Vibe. I broke one of the bolts that connects the exhaust pipe to the exhaust manifold. Need to get some type of nut/bolt/spring that I could use to fix it. The bolt is sticking out of the flange about 3/4" if I had a long nut to screw onto that?...........
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Thermostat Housing Broken Bolt - Replace Water Pump?
So I tried to replace my thermostat and housing and the housing bolt snapped off. Ok so I tried to extract that bolt off and the extractor bolt snapped off inside. I am guessing it might just be easiest to replace the water pump now? I am pretty much at the end of my mechanical rope which is short anyhow.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Oil Leak From Exhaust Manifold
I own a e1999 Ford F350 7.3 4x4 with a Garrett GTP38R turbo. I have been having issues with very little power and pulled an CEL of P0221. I know it's for the APS and have been trying to trouble shoot it as a new APS has not fixed the problem. However, while working on that I just noticed an oil leak appear. I tracked it down and can visibly see it leaking out the top of the passenger side exhaust manifold in two places. It is seeping out the top. Is oil supposed to even be running through here like that?
I recently replaced my up pipes with the newer style bellowed ones. While I had the turbo off I replaced all the o-rings top and bottom and did the EBPV delete on the pedestal. I have been having very little power and cannot the truck over 5-10 MPH and stays at low RPM's so I originally thought it was the leaky up pipes. Those were fixed along with fuel pressure checks which came back good. I then pulled the P0221 code finally. While I had the turbo off I inspected it and it did spin freely and had no side to side play in it.
What was unusual to me was there was a small pooling of oil in the turbo when I took it off. I know the CCV goes through here so some oil is normal. Also, when I was diagnosing the up pipe leak I could see a small amount of oil spraying out the blown donut gasket along with the exhaust gases. I don't think that is normal.
Is there an internal seal in the turbo that can go bad causing oil to spill into my exhaust and possibly leak at the exhaust manifold? Or do I have an internal oil leak from somewhere else?
Ford F-150 - 1997-2003 :: Exhaust Leak On Passenger Side / Broken Exhaust Manifold Bolts
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Oil Leaking From Driver Side Exhaust Manifold At Junction With Up-Pipe
I had a fuel starvation problem because Ford painted the inside of the fuel tank and the paint was coming off and clogging the filters and because I foolishly drove it I now have white smoke spewing out of the tail pipe and an engine miss.
I also explained that I thought that the white smoke did not smell sweet like antifreeze, but rather like diesel. (Hoping that a head gasket replacement is not required.)
I am in the middle of doing the Hutch Mod with frame-mounted Racor PS120-2 jar-type screen pre-pump filter and shortening my previous Harpoon Mod and paint stripping and powerwashing the inside of my tank. Next I plan to move on toward the engine issue.
This evening I was under the van with a flashlight and I noticed that there was a black liquid of some sort at the driver's side exhaust manifold where it joins the up-pipe. At first I was afraid to touch it fearing that it would be carbon-sooted water, but it felt and tasted like carbon-sooted diesel.
And since I haven't started the engine in two weeks and it has been routinely near or over 100F in Sacramento, water would have likely evaporated days ago.
Does it make sense if the fuel starvation problem caused an injector nozzle or its cup to crack or to stick open or to otherwise spew unburnt fuel into the exhaust manifold which would cause the white smoke? Obviously, the unburnt fuel must get from the affected cylinder(s) to the tail pipe somehow, which likely means out the exhaust valve, through the exhaust manifold to the up-pipe and through the turbo to the exhaust pipe and finally to the tail pipe.
See pictures at my CP. I can't figure out how to attach them or put them inline here because it still says I can't do attachments.
What is my next move? Remove the driver's side valve cover? If so, what should I look for, etc.?
2002 E350 extended body van 7.3 diesel auto trans converted to 4x4 (bought new)
Ford 7.3L Power Stroke (1999-2003) :: Exhaust Leak At Passenger Side Up-pipe To Manifold - P1211 And P1280
I just finished installing a new turbo (shaft play and lots of oil in the compressor side), RR up-pipes, and T500 (250k and once had a very long crank to get the ICP up to start).
Anyway, except for another exhaust leak at the pass side up-pipe to manifold, it seemed to run okay but with lots of white smoke. I only have about 50 miles after the install, when it suddenly starting surging and made a lot of loud knocking noises. This then went away and came back again rather quickly. I was close to home, so I made back under power. I also received the two codes listed. My IPR is original, but two summers ago I installed the IPR re-seal kit. Everything on the IPR looked good when it came off for the T500.
After reading around, I saw that low fuel pressure / air in fuel can cause problems. I connected a pressure gauge to the pre-filter port on the filter housing, and got 40psi at idle. I then took a diesel shower and blew out the fuel line into the tank. After re-connecting it, the fuel pressure stayed the same but the engines idles much better, but still has blue smoke. It's the original fuel pump (to me anyway) and original fuel line connections.
I have about 3/4 tank, and no place to put it, so I'd need to run it out for the Hutch mod, or least to get in there and inspect. Would eliminating the Ford connections at the pump be worthwhile for now, and is 40psi at idle adequate? Wondering if it's time for a fuel pump?
Ford F-150 - 1997-2003 :: F350 - Exhaust Manifold And Two Of Lower Intake Bolts Broken
I have a 97 f350 crew cab xl stock everything. 351 windsor in it I do believe. as of right now He is broken down pulled apart in my garage. Due to a much requested headgasket replacement. In any event long story short I got him all apart to discover that there was someone in it before me & had broken the infamous exhaust manifold bolts (5) and two of the lower intake bolts, (of course I've tried the correct route in removing these broken bolts/studs but again the year of the truck (1997) & its bone stock no way their moving...
So of course I tried the next best thing (on a budget) which is to drill them out, but I went to far into the exhaust manifold bolt holes, And now I believe that I've ruined the heads is this so? If so who knows where i can get a decent set of bolt on heads ready to go. yes this is my daily driver & since He's been down I've been going deeper in dept.
Ford F-150 - 1997-2003 :: Multiple Exhaust Manifold Studs Broken On Both Side / Codes P1131 And P1151
I have a 2000 with a 5.4 and 166K miles. It had multiple exhaust manifold studs broken on both sides. Now that thay is fixed, I am getting the p1131 and p1151 codes. The EGR tube was also replaced at the time of the manifold fix. I checked over all the tubes and electrical connectors to rule out something simple but did not find anything out of place. The intake manifold was replaced with a new Napa one less than 5K miles ago as well.
Could the leaky exhaust manifolds over time set the fuel trim level high and now that they are fixed, the ECM is thinking it is running too rich? Can the ECM be reset to zero? There is also a ticking/rattling noise when you accelerate that seems to be coming from the fuel injectors. I listened with the stethescope and they are the only things that sound like the noise I hear. Could these all be related?
Ford Super Duty (1999-2016) :: Broken Exhaust Manifold Bolts - Long Term Fix?
I've got the dreaded broken exhaust manifold studs on my 2004 F250 V10. I don't drive it much (just 50,000 miles in 10 years) and confess I've ignored the hissing for quite a while. Is there really a permanent fix for these broken studs? Or should I expect to be replacing broken studs every 2 or 3 years?
If there is a permanent fix what is it? Special studs? Special manifold? I want to keep this truck a long time and don't want to be replacing these studs every few years.
Ford Exhaust :: Exhaust Manifold Leak Due To Broken Rusted Bolts
I have a 97 Expedition with the 5.4 engine and 160k miles. Recently while having other work done I was told that I had an exhaust manifold leak due to broken rusted bolts.
View 3 RepliesFord Super Duty (1999-2016) :: 2008 F450 - Lost Both Turbos / Exhaust Manifold Bolts Broken
Our F-450 with 102000 miles lost both turbos also broken exhaust manifold bolts. This truck carries tools fuel tank and sometimes skid loader on trailer. Heard lots of bad things about 6.4 liter motor now first hand experience. Asked dealer if 6500.00 bill could be reduced since so close to 100000 mile warranty and was told nothing could be done. Can not afford to sell truck now also have two other Ford F-250s newest one 2012. Is there any other approach that could be taken to get some relief from this expense.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Dropped Bolt Into Motor
So I was in the process of doing a turbo swap to the borg warner sxe366 and the freeze plug that plugs the old mechanical fuel pump in the valley had to be removed well needless to say, it as well as the safety bolt I had attached to it fell into the motor, seperatly. I'm already getting the motor ready to be pulled but what are the odds that they made it to the oil pan or if they didn't any way to make them fall out?
View 10 RepliesFord 6.0L Power Stroke Diesel :: Cannot Get Exhaust Manifold Bolts Off
I can't get my exhaust manifold bolts off. They are in bad shape. The 10mm is too loose and 3/8 just rounds. I have had the torches on them too! Can the bolts be cut off with a torch?? Haven't broken any. Can't get the bolt heads to move. It's an 04, original manifolds. I am working the driver's side. I can't figure this one out. How to get this manifold off?
View 4 RepliesFord 6.0L Power Stroke Diesel :: Changing Right Exhaust Manifold?
How difficult is it to change the passenger exhaust manifold? I have just finished replacing the left exhaust manifold. The biggest issue was rusted fasteners and inexperience. Have torches. Any you tube videos show the left manifold being changed but not the right. I do not have a hoist and work in my driveway. Is the right side more difficult and should I leave it to someone with a hoist?
View 4 Replies